Perlesmith PSLT6 Manuel utilisateur
V1.0
TV WAll Mount Instruction Manual
Thank you for choosing this PERLESMITH product! At
PERLESMITH we strive to provide you with the best quality
products and services in the industry. Please share your
experience of our product with others at www.perlesmith.com/
pages/reviews if you are satisfied. Should you have any issues,
please don't hesitate to contact us.
Technical Support:
1-800-556-6806 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US）
[email protected] (CA)
Website:
www.perlesmith.com
Model: PSLT6
Weight Restrictions
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only
with the maximum weights indicated. Use with
products heavier than the maximum weights
indicated may result in failure of the mount and
its accessories, causing possible
damage and or injury.
WARNING
If your TV weighs more, this
mount is NOT compatible.
110 lbs.
(50.0 kg)
V1.0
IMPORTANT SAFETY INFORMATION
Please carefully read all instructions before attempting installation. If you do
not understand the instructions or have any concerns or questions, please
contact our Technical Support line at 1-800-556-6806 or customer service
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.
• This product is designed for use in wood stud, solid concrete, concrete
block and brick walls - DO NOT install into drywall alone.
• The wall must be capable of supporting five times the weight of the TV and
mount combined.
Check the VESA Pattern of TV before the Installation
If your TV VESA is greater than 600x400 mm/24x16in. or less than
VESA 100x100mm/4x4 in., this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
find a compatible mount.
MAX: 600mm/24 in.
MAX: 400mm/16 in.
Minimum VESA pattern:
100mm/4 in.(W)x100mm/4 in.(H)
200 mm ≈ 7 7/8 in.
400 mm ≈ 15 3/4 in.
100 mm ≈ 4 in.
300 mm ≈ 11 3/4 in.
600 mm ≈ 23 6/10 in.
01 02 03 04 05 06 07 08 09 10
Washer
M4/M5/M6
[M-D] x4
Tools Needed (Not lncluded)
Supplied Parts and Hardware
Supplied Parts and Hardware for Step 1
Warning: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use
damaged or defective parts. lf you require replacement parts, please contact our
Technical Support line at 1-800-556-6806 or customer service
• Please note: Not all hardware included in this package will be used.
Stud Finder Tape Measure Pencil Drill
7/32 in. (5.5mm)
Wood Drill 3/8 in. (10mm)
Concrete Drill 1/2in. (13 mm)
Socket Wrench
Phillips
Screwdriver
Hammer
Awl
x1
02
Left TV Bracket
Solid Concrete
or Concrete Block
CAUTION
DO NOT
install into
drywall alone Wood Studs
(with Drywall)
Verify Your Wall Construction
If you are are not sure the wall
construction, please contact our
product support line at
1-800-556-6806 or
customer service at
[email protected] (US)
[email protected] (CA)
Right TV Bracket x1
01
Note: The washer is shown in accordance with the actual size.
[05] Washer
[If necessary]
01 02 03 04 05 06 07 08 09 10
M8
M6
Note: The spacers are shown in accordance with the actual size.
[06] Spacers
[If necessary]
[07] TV Bolts
Supplied Parts and Hardware for Step 2
Ø8mm Washer
x4
B
Lag Screw
ST8X65mm
x4
A
Supplied Parts and Hardware for Step 3
[M-A1] [M-A2]
M6 x 15mm
x4
M6 x 30mm
x4
[M-B1]
M8 x 15mm x4
[M-B2]
M8 x 50mm x4
Note: The bolts are shown in accordance with the actual size.
L10mm
[M-C] x8 L5mm
[M-E] x8
Wall Plate
03 x2
Connector
Dx2
Bolt
M5 x 6mm
Ex8
01 02 03 04 05 06 07 08 09 10
x1
Level 04
Step 1 Secure the TV Brackets to TV
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination.
We recommend thread engagement by at least 5 turns.
-Too short will not hold the TV.
-Too long will damage the TV.
Please Note: The provided TV bolts meet most of today's TVs design.
However, some TVs require special bolts which may not be in the hardware
bag. In this case we offer our “PSUHP" Universal Hardware Kit which
provides a large selection of bolts that can meet the demand of older and
unique applications.
Please Note: When using the spacers it is important to note that they can
be used in multi-layers (meaning stacked). If you have any difficulty
understanding how to install the TV bolts or spacers, please contact
[email protected] (CA).
Too Short
CorrectCorrect
Too Long
Only one bolt size fits your TV.
Select TV Bolts
M6 M8
Wall
Anchor
x4
C
This anchor is for
concrete or brick walls
ONLY. DO NOT use them
in drywall or wood studs.
CAUTION!
01 02 03 04 05 06 07 08 09 10
CAUTION: Ensure the TV
brackets [01] and [02] are EQUALLY
CENTERED on your TV AND securely
fastened in place.
Option A (For Flat Back TV)
07 M-A1/M-B1
05
M-D
07 M-A2/M-B2
05
M-D
06
M-C/M-E
Option B (For Round Back TV)
01
02
01
02
UP
01 02
Alternate
Spacer
Setups
Please note: The bolt hole locations on your TV may vary in accordance of the
manufacturers design of the TV. We are only illustrating possible locations of
the bolt holes.
(If needed)
(If needed)
01 02 03 04 05 06 07 08 09 10
Step 2 Assemble Wall Plate
DO NOT overtighten.
Tighten only until snug.
Option D
For cable interference or inset holes, use
spacers [M-C] and [M-E] to create extra
space between the TV and TV brackets
01/02
M-C/M-E
06 M-A2/
M-B2
07
05
M-D
Spacers may be necessary for 2 holes ONLY.
Option C (For TV with A “Bump”)
01
02
07 M-A2/M-B2
05
M-D
06
M-C/M-E
07 M-A1/M-B1
05
M-D
03
D
E
(If needed)
(If needed)
(If needed)
Alternate
Spacer
Setups
Alternate
Spacer
Setups
01 02 03 04 05 06 07 08 09 10
3-2
3-1
16 in.
(406mm)
24 in.
(609mm)
Position the wall plate [03] at
your desired height and line
up the holes with your stud
center line. Level the wall
plate and mark the holes.
Use a stud finder(not included)
to locate wood studs or use an
awl (not included) to verify the
edges. Mark the edge and
center locations.
Step 3 Attach Wall Plate to Wall
Step 3A Wood Stud Option
X
For wood stud installation, follow STEP 3A
For concrete installation, follow STEP 3B
● Avoid potential personal injury or property damage! DO NOT over-tighten
the lag screws [A]. Tighten the lag screws [A] only until the washers [B] are
pulled firmly against the wall plate [03].
● DO NOT USE ANCHOR FOR THIS STEP!
● Ensure the wall plate is securely fastened to the wall before continuing to
the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum
1.5 x 3.5 in. (38 x 89 mm)
● Stud center must be verified
C
WARNING:
03
01 02 03 04 05 06 07 08 09 10
3-4
1/2 in.(13 mm)
Socket Wrench
(Not included)
Install the wall plate [03]
using lag screws [A].
Tighten the lag screws [A]
only until the washers [B]
are pulled firmly against the
wall plate [03].
Drill 4 pilot holes using a
7/32 in. (ø5.5 mm) diameter drill
bit. Make sure the depth is not
less than 2 9/16 in. (65 mm).
7/32 in. (ø5.5 mm)
2 9/16 in. (65 mm)
3-3
Step 3B Solid Concrete or Concrete Block Option
WARNING:
● Avoid potential personal injury or property damage! DO NOT over-tighten
the lag screws [A]. Tighten the lag screws [A] only until the washers [B] are
pulled firmly against the wall plate [03].
● Ensure the wall plate is securely fastened to the wall before
continuing to the next step.
● Mount the wall plate [03] directly onto the concrete surface.
● Anything covering the wall must not exceed 5/8 in. (16 mm)
● Minimum solid concrete thickness: 203 mm (8 in.)
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
● Never drill into the mortar between blocks
Wall
Anchor
C
A
03
2
B
01 02 03 04 05 06 07 08 09 10
A
03
2
B
1/2 in.(13 mm)
Socket Wrench
(Not included)
3B-1
Position the wall wall plate [03]
at your desired height, level the
wall plate and mark the pilot
hole locations.
3B-2
3/8 in.(ø10mm)
2 3/4 in.(70mm)
Drill 4 pilot holes using a 3/8 in.
(10mm) diameter drill bit. Make
sure the depth is not less than
2 3/4 in.(70mm). Never drill into
the mortar between blocks.
3B-3
Use the hammer to knock
anchors [C] into the wall. Be sure
the anchors [C] are seated flush
with the concrete surface.
C
3B-4
Install the wall plate [03] using lag
screws [A]. Tighten the lag screws [A]
only until the washers [B] are pulled
firmly against the wall plate. DO NOT
over-tighten the lag screws [A].
03
01 02 03 04 05 06 07 08 09 10
Table des matières
Autres manuels Perlesmith Support TV
Perlesmith
Perlesmith PSLF4 Manuel utilisateur
Perlesmith
Perlesmith PSTVS07 Manuel utilisateur
Perlesmith
Perlesmith PSLFK3 Manuel utilisateur
Perlesmith
Perlesmith PSLTK1 Manuel utilisateur
Perlesmith
Perlesmith PSTVS01 Manuel utilisateur
Perlesmith
Perlesmith PSTVS04 Manuel utilisateur
Perlesmith
Perlesmith PSLFK1-24 Manuel utilisateur
Perlesmith
Perlesmith PSXFK1 Manuel utilisateur
Perlesmith
Perlesmith PSCM2 Manuel utilisateur
Perlesmith
Perlesmith PSLFK1 Manuel utilisateur
Perlesmith
Perlesmith PSTVS01 Manuel utilisateur
Perlesmith
Perlesmith PSFS01 Manuel utilisateur
Perlesmith
Perlesmith PSSL1 Manuel utilisateur
Perlesmith
Perlesmith PSCMF1 Manuel utilisateur
Perlesmith
Perlesmith PSXF4 Manuel utilisateur
Perlesmith
Perlesmith PSMFK13 Manuel utilisateur
Perlesmith
Perlesmith PSLF6 Manuel utilisateur
Perlesmith
Perlesmith PSLFK3-24 Manuel utilisateur
Perlesmith
Perlesmith PSTVS20 Manuel utilisateur
Perlesmith
Perlesmith PSTVS02 Manuel utilisateur
