PEERLESS PARAMOUNT PRFLU Manuel utilisateur
ISSUED: 11-02-09 SHEET #: 202-9393-1
Paramount™ Universal Flat Wall Mount
for 32" - 60" LCD and Flat Panel
Plasma Screens
Max UL Load Capacity: 200 lb (90.7kg)
Model: PRFLU
Installation Guide
This product was designed to be installed on wood stud walls and solid concrete (2000 psi density
minimum) or cinder block walls. Before installing make sure the supporting surface will support the
combined load of the equipment and hardware. Screws must be tightly secured. Do not overtighten
screws or damage can occur or product may fail. Never exceed the Maximum UL Load Capacity.
This product is intended for indoor use only. Use of this product outdoors could lead to product
failure or personal injury. This mount is designed to attach the screen 0.63" from the wall. Please
refer to manufacturer's installation guide recommendations for required distance from wall to
avoid risk of injury or property damage. For support please call customer care at 1-800-865-2112.
WARNING
©
UL
USC
I
D
:
0
0
0
0
0
1
8
7
6
2
2 of 27 ISSUED: 11-02-09 SHEET #: 202-9393-1
E(4)
M4 x 12 mm
T(1)
C(4)D(4)
F(4)
M4 x 25 mm
G(4)
M5 x 12 mm H(4)
M5 x 25 mm
I(4)
M6 x 12 mm J(4)
M6 x 20 mm K(4)
M6 x 25 mm
L(4)
M6 x 30 mm
M(6)
M8 x 16 mm N(4)
M8 x 25 mm O(4)
M8 x 40 mm
P(4)
ID .22" (5.6 mm)
Q(4)
ID .34" (8.7 mm)
R(6)
A(1)
B(2)
Tools Needed for Assembly
• stud nder ("edge to edge" stud nder is
recommended)
•phillips screwdriver
•drill
• 5/32" (4 mm) bit for wood stud wall
• 5/16" (8 mm) bit for concrete and cinder block
• level
• hammer (optional)
3 of 27 ISSUED: 11-02-09 SHEET #: 202-9393-1
Installation to Double Wood Stud Wall
1
Use wall plate (A) as a template, make sure it is level, and mark four mounting holes along the center
lines of the wood studs. Drill four 5/32" (4 mm) dia. holes 2.5" (64 mm) deep. Level wall plate (A) and
attach to wall with four wood screws (C) into stud center. Use of an edge to edge stud nder is highly
recommended. Tighten screws rmly, but do not overtighten.
A
C
Do not over tighten screws, or
damage may occur.
TOP CUTAWAY VIEW
Wood screws must
center in stud.
STUD
C
A
WARNING WARNING
4 of 27 ISSUED: 11-02-09 SHEET #: 202-9393-1
Installing to Solid Concrete or Cinder Block
1
Level wall plate (A) and use as a template to mark four mounting holes. Drill four 5/16" (8 mm) dia.
holes to a minimum depth of 2.5" (64 mm). Insert four anchors (D) into holes and secure wall plate
(A) with four screws (C). Tighten screws rmly, but do not overtighten.
SOLID CONCRETE
CINDER BLOCK
C
D
A
5 of 27 ISSUED: 11-02-09 SHEET #: 202-9393-1
1
2
D
A
D
C
concrete
Place plate (A) over anchors (D). Secure with screws (C). Tighten screws.
Drill holes and insert anchors (D).
• When installing Peerless wall mounts on cinder block, verify that you have a minimum
of 1-3/8" (35 mm) of actual concrete thickness in the hole to be used for the concrete
anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, gener-
ally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM C-90
specications. It is suggested that a standard electric drill on slow setting is used to drill the
hole instead of a hammer drill to avoid breaking out the back of the hole when entering a
void or cavity.
• Always attach concrete anchors directly to load-bearing concrete.
WARNING
CUTAWAY VIEW
INCORRECT
CORRECT
plaster/
drywall
concrete
plaster/
drywall
wall plate
wall plate
CORRECT
WARNING
concrete
6 of 27 ISSUED: 11-02-09 SHEET #: 202-9393-1
To prevent scratching the screen, set a cloth on a at, level surface that will support the weight of
the screen. Place screen face side down. If screen has knobs on the back, remove them to allow
the adapter brackets to be attached. Place adapter brackets (B) on back of screen, align to
holes, and center on back of screen as shown below. Attach the adapter brackets to the back of
the screen using the appropriate combination of screws, multi-washers, and spacers as shown
in gure 2.1 or 2.2.
NOTE: Top and bottom holes on screen must always be used.
Verify that all holes are properly aligned, and then tighten screws using a phillips
screwdriver.
2
Installing Adapter Brackets
Notes:
• The number of fasteners used
will vary, depending upon the
type of screen.
• Multi-washers and spacers may
not be used, depending upon
the type of screen.
• Use the corresponding hole in
the multi-washer that matches
your screw size.
MEDIUM HOLE
FOR M5 SCREWS
SMALL HOLE
FOR M4 SCREWS
LARGE HOLE
FOR M6 SCREWS
MULTI-WASHER
NOTE: "X" dimensions should be equal.
BCENTER BRACKETS
VERTICALLY ON BACK
OF SCREEN
X
X
7 of 27 ISSUED: 11-02-09 SHEET #: 202-9393-1
For Bump-out or Recessed Back Screen
2-2 Refer to screen compatibility chart to determine the proper fastener to use. Visit
www.peerlessmounts.com/2 for a full screen compatibility chart for this mount.
Begin with longer length screw, hand thread through multi-washer, adapter bracket (B) and
spacer in that order into screen as shown below. Screw must make at least three full turns
into the mounting hole and t snug into place. Do not over tighten. If screw cannot make
three full turns into the screen, select a longer length screw from the bafed fastener pack.
Repeat for remaining mounting holes, level brackets and tighten screws.
2-1 Refer to screen compatibility chart to determine the proper fastener to use. Visit
www.peerlessmounts.com/2 for a full screen compatibility chart for this mount.
Begin with the shortest length screw, hand thread through multi-washer and adapter
bracket (B) into screen as shown below. Screw must make at least three full turns into the
mounting hole and t snug into place. Do not over tighten. If screw cannot make three full
turns into the screen, select a longer length screw from the bafed fastener pack. Repeat for
remaining mounting holes, level brackets and tighten screws.
NOTE: Spacers may not be used, depending upon the type of screen.
For Flat Back Screen
ADAPTER BRACKET (B)
SCREEN g 2.1
MULTI-WASHER
SCREW
If you have any questions, please call Peerless customer care at 1-800-865-2112.
If you have any questions, please call Peerless customer care at 1-800-865-2112.
SCREEN
MULTI-WASHER
SCREW
g 2.2
SPACER
• If screws don't get three complete turns in the screen inserts or if screws bottom out and
bracket is still not tightly secured, damage may occur to screen or product may fail.
WARNING
ADAPTER BRACKET (B)
8 of 27 ISSUED: 11-02-09 SHEET #: 202-9393-1
Failure to lock brackets (B) with safety
screws can cause sceen to come off mount
if hit accidentally.
WARNING
Mounting and Removing Flat Panel Screen
3
Hook adapter brackets (B) onto wall plate (A). Then slowly swing screen in as shown. Turn safety
screws, using allen wrench (T) clockwise at least six times to prevent screen from being removed as
shown in detail 1 of gure 3.1. Always use an assistant to safely lift and position the at panel screen.
Screen can be adjusted horizontally if desired as shown in gure 3.2.
NOTE: To lock the screen down, tighten safety screws to wall plate as shown in detail 1.
To remove screen from mount, loosen safety screws, swing screen away from mount and lift screen
off of mount.
A
B
g. 3.1
DETAIL 1
B
A
g. 3.2
SAFETY SCREWS
PUBLICADO: 11-02-09 HOJA #: 202-9393-1
Máxima capacidad (UL) de carga: 200 lb (90.7kg)
Modelo: PRFLU
Guía para la instalación
Soporte universal de pared plano
Paramount™ para pantallas LCD y pantallas
planas de plasma de 32" a 60"
Este producto está diseñado para ser instalado en paredes con montantes de madera y en
paredes de concreto macizo (de una densidad mínima de 2,000 psi) o de bloques de hormigón.
Antes de instalarlo, asegúrese de que la supercie de apoyo sostendrá la carga combinada
del equipo y los jadores. No apriete los tornillos en exceso; los podría dañar. Nunca exceda
la Capacidad Máxima (UL) de Carga. Este producto está diseñado para uso en interiores
solamente. Utilizar este producto en exteriores podría causar fallas del producto o lesiones
a individuos. Este soporte está diseñado para sostener la pantalla a 0.63" de la pared. Por
favor, repase las recomendaciones del manual de instalación del fabricante con respecto a
la distancia necesaria de la pared para evitar el riesgo de sufrir lesiones o causar daños a la
propiedad. Si necesita ayuda, por favor, llame a Servicio al Cliente de Peerless al 1-800-865-2112.
ADVERTENCIA
©
UL
USC
I
D
:
0
0
0
0
0
1
8
7
6
2
10 de 27 PUBLICADO: 11-02-09 HOJA #: 202-9393-1
Español
T(1)
C(4)
E(4)
M4 x 12 mm
D(4)
F(4)
M4 x 25 mm
G(4)
M5 x 12 mm H(4)
M5 x 25 mm
I(4)
M6 x 12 mm J(4)
M6 x 20 mm K(4)
M6 x 25 mm
L(4)
M6 x 30 mm
M(6)
M8 x 16 mm N(4)
M8 x 25 mm O(4)
M8 x 40 mm
P(4)
ID .219" (5.56 mm)
Q(4)
ID .344" (8.74 mm)
R(6)
A(1)
B(2)
Herramientas necesarias para el ensamblaje
• localizador de montantes (se
recomienda uno de "borde a borde")
• destornillador phillips
• taladro
• broca de 5/32" (4 mm) para paredes
con montantes de madera
• broca de 5/16" (8 mm) para concreto
macizo o de bloques de hormigón de
escorias
• nivel
• martillo (opcional)
Table des matières
Langues :
Autres manuels PEERLESS Support TV
PEERLESS
PEERLESS CMJ 470 Mode d’emploi
PEERLESS
PEERLESS MM746PU Manuel utilisateur
PEERLESS
PEERLESS HP450-GB Mode d’emploi
PEERLESS
PEERLESS SUF640P and assembly Mode d’emploi
PEERLESS
PEERLESS SUF660P and assembly Mode d’emploi
PEERLESS
PEERLESS VML11 Mode d’emploi
PEERLESS
PEERLESS SUA746PU Mode d’emploi
PEERLESS
PEERLESS DS508 and assembly Mode d’emploi
PEERLESS
PEERLESS Smartmount D-FPT-220 Mode d’emploi
PEERLESS
PEERLESS PM1327 Mode d’emploi
PEERLESS
PEERLESS Smartmount ST640 Manuel utilisateur
PEERLESS
PEERLESS Jumbo 2000 JM 2630 Mode d’emploi
PEERLESS
PEERLESS PARAMOUNT PT632 and assembly Mode d’emploi
PEERLESS
PEERLESS PLA1-UN7 Mode d’emploi
PEERLESS
PEERLESS Designer Series Mode d’emploi
PEERLESS
PEERLESS SP 850 and assembly Mode d’emploi
PEERLESS
PEERLESS ST 632P Mode d’emploi
PEERLESS
PEERLESS Smartmount ST640 Manuel utilisateur
PEERLESS
PEERLESS LWS410/BK Mode d’emploi
PEERLESS
PEERLESS PARAMOUNT PF630 and assembly Mode d’emploi
