peerless-AV Paramount PA735F Mode d’emploi
ISSUED: 02-15-10 SHEET #: 095-9317-3 07-26-11
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.com
Models: PA735F, PA735F-S
Installation and Assembly:
Paramount™ Articulating Wall Arm for 10" - 26" Flat
Panel Displays
Max UL Load Capacity: 25 lb (11.3 kg)
2 of 38 ISSUED: 02-15-10 SHEET #: 095-9317-3 07-26-11
NOTE: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
• stud finder ("edge to edge" stud finder is recommended)
• phillips screwdriver
• drill
• 5/16" (8mm) bit for concrete and cinder block wall
• 5/32" (4mm) bit for wood stud wall
• level
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum UL Load Capacity. See page one.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an
"edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION HARDWARE REQUIRED
• Wood Stud Included
•Wood Beam Included
•Solid Concrete Included
•Cinder Block Included
•Brick Contact Qualified Professional (not evaluated by UL)
•Other or unsure? Contact Qualified Professional
WARNING
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Wood Stud Wall................................................................................................................................................4
Installation to Solid Concrete and Cinder Block .....................................................................................................................5
3 of 38 ISSUED: 02-15-10 SHEET #: 095-9317-3 07-26-11
A
B
D
E
C
L
G
F
H
Parts may appear slightly different than illustrated.
Before you begin, make sure all parts shown are included with your product.
IJK
PA735F PA735F-S
Description Qty. Part # Part #
Awall arm assembly 1 095-P1708 095-4708
Badapter brackets 2 095-P1944 095-4944
C#14 x 2.5" flat head wood screw 2 520-1202 520-2165
Dconcrete anchor 2 590-0320 590-0320
EM4 x 12 mm screw 4 504-9013 504-2013
FM4 x 20 mm screw 4 504-9020 504-2014
Gspacer 4 590-5005 590-5003
H#10 washer 4 540-9400 540-9442
Icable ties 2560-1756 560-1756
Jcable tie anchors 2590-1290 590-1290
K8-32 x 1/4" phillips screw 2520-1622 520-1622
L5 mm allen wrench 1560-9640 560-9640
M3/16" allen wrench 1560-0071 560-0071
Parts List
M
4 of 38 ISSUED: 02-15-10 SHEET #: 095-9317-3 07-26-11
2.7"
(69 mm)
CS
Installation to Wood Stud Wall
Use a stud finder to locate the edges of the studs. Based on their edges, draw a vertical line down each stud’s
center. Place wall plate (A) on wall as a template. The top mounting slots should be located 2.7" (69mm) below
the desired display center as shown in figure 1.1. Level wall plate, and mark the center of the two mounting holes.
Make sure that the mounting holes are on the stud centerlines. Drill two 5/32" (4mm) dia. holes 2.5" (64mm) deep.
Make sure that the wall plate is level, and secure it using four #14 x 2.5" wood screws (C) as shown in fig. 1.2.
fig. 1.1
CS = CENTER OF DISPLAY
A
STUD
WALL PLATE (A)
C
fig. 1.2
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.
Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).
WARNING
1
5 of 38 ISSUED: 02-15-10 SHEET #: 095-9317-3 07-26-11
Installation to Solid Concrete or Cinder Block
Make sure that wall plate (A) is level, use it as a
template to mark four mounting holes. The top
mounting slots should be located 2.7" (69mm)
above the desired display center as shown in
figure 1.1 on page 4. Drill two 5/16" (8mm) dia.
holes to a minimum depth of 2.5" (64mm). Insert
anchors (D) in holes flush with wall as shown
(right). Place wall plate over anchors and secure
with two #14 x 2.5" screws (C). Level, then tighten
all fasteners.
SOLID CONCRETE CINDER BLOCK
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35mm) of actual
concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount
in a solid part of the block, generally 1" (25mm) minimum from the side of the block. Cinder block must meet ASTM
C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware
and components.
WARNING
1
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Always attach concrete expansion anchors directly to
load-be aring concrete.
• Never attach concrete expansion anchors to concrete
covered with plaster, drywall, or other finishing
material. If mounting to concrete surfaces covered
with a finishing surface is unavoidable (not evaluated
by UL), the finishing surface must be counterbored
as shown below. Be sure concrete anchors do not
pull away from concrete when tightening screws. If
plaster/drywall is thicker than 5/8" (16mm), custom
fasteners must be supplied by installer (not evaluated
by UL).
WARNING
CUTAWAY VIEW
INCORRECT CORRECT
plaster/
drywall plaster/
drywall
concrete concrete C
D
WALL PLATE (A)
D
Drill holes and insert anchors (D).
Place wall plate (A) over anchors (D) and secure with screws (C).
Tighten all fasteners.
A
D
C
concrete
surface
1
3
2
A A
6 of 38 ISSUED: 02-15-10 SHEET #: 095-9317-3 07-26-11
Installing Adapter Brackets
To prevent scratching the display, set a cloth on a flat, level surface that will support the weight of the display.
Place display face side down. If display has knobs on the back, remove them to allow the adapter brackets to
be attached. Place adapter brackets (B) on back of display, align to holes, and center on back of display as
shown below. Attach the adapter brackets to the back of the display using the appropriate combination of screws,
washers, and spacers as shown in steps 2-1 or 2-2.
NOTE: Top and bottom holes must always be used.
Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver.
NOTE: For flat back displays proceed to step 2-1. For bump-out or recessed back display skip to step 2-2.
B
CENTER BRACKETS
VERTICALLY
ON BACK OF DISPLAY
X
X
NOTE: "X" dimensions should be equal.
• Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can
cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to display or product may fail.
WARNING
2
7 of 38 ISSUED: 02-15-10 SHEET #: 095-9317-3 07-26-11
Begin with the shortest length screw, hand thread through washer and adapter bracket into display as shown
below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over
tighten. If screw cannot make three full turns into the display, select a longer length screw from the baffled
fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
NOTE: Spacers may not be used, depending upon the type of display.
Begin with longer length screw, hand thread through washer, adapter bracket and spacer in that order into display
as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not
over tighten. If screw cannot make three full turns into the display, select a longer length screw from the baffled
fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
For Flat Back Display
For Bump-out or Recessed Back Display
ADAPTER BRACKET (B)
DISPLAY
WASHER
SCREW
2-2
2-1
If you have any questions, please call Peerless customer care at 1-800-865-2112.
If you have any questions, please call Peerless customer care at 1-800-865-2112.
DISPLAY
WASHER
SCREW
ADAPTER BRACKET (B)
SPACER
8 of 38 ISSUED: 02-15-10 SHEET #: 095-9317-3 07-26-11
Mounting and Removing Flat Panel Display
Hook adapter brackets (B) onto adapter plate (A).
Turn security screws, using phillips screwdriver,
clockwise at least six times to prevent display from
being removed as shown in cross section of fig.
3.1.
NOTE: To lock the display down, tighten safety/
security screws to wall plate as shown in cross
section.
To remove display from mount, loosen safety/
security screws, swing display away from mount,
and lift display off of mount.
3
• Always use an assistant or mechanical lifting equipment to safely lift and position the flat panel displays.
WARNING
B
• Do not tighten screws with excessive force.
Overtightening can cause damage to mount. Tighten
screws to 40 in. • lb (4.5 N.M.) maximum torque.
CAUTION
fig 3.1
A
SECURITY
SCREWS
B
A
• If screws become loose over time, tighten screws as
necessary. Tighten screws to 50 in • lbs
(5.6 N.m.) maximum torque.
WARNING
10-32 x 1/2" screws are pretensioned and require
no adjustment. Rotate display by hand to level
display. Roll bracket allows 2° roll adjustment.
4
ROLL BRACKET
1/4-20 X 1/2" SCREWS
CROSS SECTION
9 of 38 ISSUED: 02-15-10 SHEET #: 095-9317-3 07-26-11
Cords may be routed using cable ties (I).
Attach cable tie anchor (J) to top or bottom of wall arm (A) using 8-32 x 1/4" phillips screw (K) as shown in
figure 5.1.
Secure cables to top or bottom of wall arm (A) using cable ties (I) as shown in figure 5.2.
fig. 5.1 fig. 5.2
Cable Management
KI
I
J
CORD
WALL ARM (A)
5
If more or less tension is desired in the arm pivot points, do the following:
• To increase tension, turn tension screw(s) clockwise using 5mm allen wrenchs (L). NOTE: Tighten screws to
50 in. • lb (5.6 N.M.) maximum torque.
• To reduce tension, turn tension screw(s) couter-clockwise using 5mm allen wrenchs (L). NOTE: Do not loosen
more than half a turn.
6
Tension Adjustment
• Do not remove screw or loosen screw until it is no longer engaged with the mount. Doing so may cause the display
to fall.
• If screws become loose over time, tighten screws as necessary. Tighten screws to 50 in. • lb (5.6 N.M.) maximum
torque.
WARNING
TENSION SCREWS
© 2011, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Peerless Industries, Inc.
3215 W. North Ave.
Melrose Park, IL 60160
www.peerlessmounts.com
PUBLICADO: 02-15-10 HOJA #: 095-9317-3 07-26-11
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.com
Modelos: PA735F, PA735F-S
Instalación y montaje:
Paramount™ Brazo de pared articulado para Plana Pantalla de
10" a 26"
Capacidad máxima de soportar carga por UL:25 lb (11.3 kg)
Ce manuel convient aux modèles suivants
1
Table des matières
Langues :
Autres manuels peerless-AV Support TV
peerless-AV
peerless-AV PLA50-UNL Mode d’emploi
peerless-AV
peerless-AV ESA763PU Manuel utilisateur
peerless-AV
peerless-AV LCT620AD-G Manuel utilisateur
peerless-AV
peerless-AV PLAV70-UNL-S Mode d’emploi
peerless-AV
peerless-AV PC930 Series Mode d’emploi
peerless-AV
peerless-AV SUF661 Mode d’emploi
peerless-AV
peerless-AV ACC-V1500X Manuel utilisateur
peerless-AV
peerless-AV DS-S555-3X2 Manuel utilisateur
peerless-AV
peerless-AV ACC-DSV449-P Mode d’emploi
peerless-AV
peerless-AV SUT645P Manuel utilisateur
peerless-AV
peerless-AV HLG440-PH Mode d’emploi
peerless-AV
peerless-AV IWB680-W Manuel utilisateur
peerless-AV
peerless-AV TTS4X4 Manuel utilisateur
peerless-AV
peerless-AV PTLP650 Manuel utilisateur
peerless-AV
peerless-AV PLA60-UNL Mode d’emploi
peerless-AV
peerless-AV SmartMount SA735P Mode d’emploi
peerless-AV
peerless-AV PDW T XL Mode d’emploi
peerless-AV
peerless-AV Paramount PA746 Manuel utilisateur
peerless-AV
peerless-AV Designer Series Manuel utilisateur
peerless-AV
peerless-AV SFL624 Manuel utilisateur
