Peerless-AV PA740 Mode d’emploi

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 01-27-08 SHEET #: 095-9283-2 03-18-08

Features:

•Fits 22" to 40" LCD screens

• Three tensionable pivot points for extensive adjustment of viewing angle

• VESA®75/100/200 x 100/200 x 200 compatible

• Frees up space by folding flat against the wall

Maximum UL Load Capacity: 80lb (36 kg)

ThisproductisULListed.

It must be installed by a

qualified professional

installer.

Installation and Assembly:

Paramount™ Pivot for 22" to 40" LCD screens

Models: PA740, PA740-S

2 of 30 ISSUED: 01-27-08 SHEET #: 095-9283-2 03-18-08

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

For customer care call (800) 865-2112 or (708) 865-8870.

Table of Contents

Parts List .............................................................................................................................................................................. 3

Installation to Wood Stud Wall ............................................................................................................................................. 4

Installation to Solid Concrete and Cinder Block .................................................................................................................... 5

Tools Needed for Assembly

• stud finder ("edge to edge" stud finder is recommended)

• phillips screwdriver

• 3/16" allen wrench

• drill with 1/4" and 5/32" drill bits

NOTE: Read entire instruction sheet before you start installation and assembly.

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please

call Peerless customer care at 1-800-865-2112.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-

ware and components.

• Never exceed the Maximum UL Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an

"edge to edge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed and intended to be mounted to the following supporting surfaces checked below with the

hardware included in this product as specified in the installation sheet. To mount this product to an alternative support-

ing surface, contact Peerless customer care at 1-800-865-2112.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION ADDITIONAL HARDWARE REQUIRED

xWood Stud None

xWood Beam None

xSolid Concrete None

xCinder Block None

Metal Stud Do not attach except with Peerless accessory kit for metal studs;

Contact Customer Service for Peerless accessory kit for metal studs.

Brick Contact Customer Service

Other or unsure? Contact Customer Service

WARNING

3 of 30 ISSUED: 01-27-08 SHEET #: 095-9283-2 03-18-08

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

B E

C F

GIJ

MNO

PA740 PA740-S

Description Qty. Part # Part #

Awall mount assembly 1 095-0546-GB 095-0546-SS

BAlligator®anchor 2 590-0097 590-0097

Cretaining spacer 4 590-5005 590-5003

D1/4-20 x 1/2" flat head phillips screw 2 520-1209 520-2178

EM4 x 10 mm phillips screw 4 504-9012 520-2027

FM4 x 20 mm phillips screw 4 504-9020 504-2014

GM6 x 12 mm phillips screw 4 520-1128 520-2039

H#14 x 2-1/2" flat head wood screw 2 520-1202 520-2165

IM6 x 20 mm phillips screw 4 520-9402 520-2040

JM6 x 30 mm phillips screw 4 510-9109 520-2042

KM5 x 6 mm phillips screw 5 520-1023 520-2214

L#10 flat washer 4 540-9400 540-9442

Mhook bracket 1 095-P1346 095-S4346

Nadapter plate 1 095-P1322 095-S4322

O#10-32 x 1/4" flat head phillips screw 1 520-1108 520-2108

Pcable tie 3 560-1725 560-2007

Parts List

4 of 30 ISSUED: 01-27-08 SHEET #: 095-9283-2 03-18-08

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

Installation to Wood Stud Wall

Using a stud finder, locate and mark the edges of the wood stud used in mounting this product. Use of an edge to

edge stud finder is highly recommended. Use a level to draw a vertical line down the center of the stud. Use wall

plate as template to mark center of holes along the vertical line. Drill two 5/32" (4 mm) dia. holes 2.5" (65 mm)

deep. Attach wall mount (A) to wall using two #14 x 2.5" flat head wood screws (H) as shown.

Skip to step 2 on page 6.

WOOD

STUD

WALL

PLATE

• Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws,

greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the studs. The use of an "edge to edge" stud finder is

highly recommended.

WARNING

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

WARNING

5 of 30 ISSUED: 01-27-08 SHEET #: 095-9283-2 03-18-08

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

• Concrete anchors are not intended for attachment to

concrete wall covered with a layer of plaster, drywall,

or other finishing material as shown below. If mounting

to concrete wall covered with plaster/drywall is

unavoidable, plaster/drywall (up to 5/8" thick) must be

counterbored as shown below. Be sure concrete

anchors do not pull away from concrete when tighten-

ing screws. If plaster/drywall is thicker than

5/8", custom fasteners must be supplied by installer

(not UL evaluated).

WARNING

Installation to Solid Concrete and Cinder Block

1Level and use wall plate as template to mark center

of holes. Drill two 1/4" (6 mm) dia. holes to a

minimum depth of 2.5" (64 mm). Insert anchors (B)

in holes flush with wall as shown in fig 1.1. Place

wall mount (A) over anchors and secure with wood

screws (H) as shown in figures 1.2 and 1.4. Make

sure wall mount is level, and tighten all fasteners.

See figure 1.3.

CONCRETE

WALL

Drill holes and insert anchors (B).

Place wall plate over anchor (B) and secure with screw (H).

Tighten all fasteners.

WALL PLATE

fig. 1.1

fig. 1.2

fig. 1.3

CUTAWAY VIEW

CORRECT

concrete

plaster/

dry wall

INCORRECT

concrete

plaster/

dry wall

• Tighten screws so that wall plate is firmly attached,

but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

fig. 1.4

WALL PLATE

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications.

It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid

breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

WARNING

SOLIDCONCRETE CINDERBLOCK

6 of 30 ISSUED: 01-27-08 SHEET #: 095-9283-2 03-18-08

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

Attaching Adapter Plate to Screen with VESA 200 x 100 or 200 x 200 Mounting Pattern

Attach hook bracket (M) to adapter plate (N) using

four M5 x 6 mm screws (K) and #10 washers (L) as

shown.

FOR VESA 200 x 100 MOUNTING PATTERN:

Choose hole pattern as shown below. Attach adapter

plate (N) to back of screen using four M4 x 10 mm

screws (E) as shown below.

*NOTE: If screw (E) gets less than three threads of

engagement, attach adapter plate (N) to back of

screen using four M4 x 20 mm screws (F) and four

spacers (C) as indicated below.

Skip to step 3 on page 9.

FOR VESA 200 x 200 MOUNTING PATTERN:

Choose hole pattern as shown below. Attach adapter

plate (N) to back of screen using four M6 x 12 mm

screws (G) as shown below.

*NOTE: If screw (G) gets less than three threads of

engagement, attach adapter plate (N) to back of

screen using four M6 x 20 mm screws (I). If screw (I)

still gets less than three threads of engagement, use

four M6 x 30 mm screws (J).

Skip to step 3 on page 9.

*For screens with a hole

pattern in a pocket,

spacers (C) go between

adapter plate (N) and

screen.

NOTE: For VESA 75 mm and 100 mm patterns, see

followingpage.

2-1

• If screws don't get three complete turns in the screen inserts or if screws bottom out and adapter plate is still not

tightly secured, damage may occur to screen or product may fail.

WARNING

7 of 30 ISSUED: 01-27-08 SHEET #: 095-9283-2 03-18-08

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

Attaching Hook Bracket to Screen with VESA 75 or 100 Mounting Pattern

*For screens with a hole

pattern in a pocket,

spacers (C) go between

hook bracket (M) and

screen.

FORVESA®75 MOUNTING PATTERN:

Choose hole pattern as shown below. Attach hook

bracket (M) to back of screen using four M4 x 10 mm

screws (E) as shown below.

*NOTE: If hole pattern is in a pocket, attach hook

bracket (M) to back of screen using four M4 x 20 mm

screws (F) and four retaining spacers (C) as indicated

below.

FORVESA 100MOUNTING PATTERN:

Choose hole pattern as shown below. Attach hook

bracket (M) to back of screen using four M4 x 10 mm

screws (E) as shown below.

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

8 of 30 ISSUED: 01-27-08 SHEET #: 095-9283-2 03-18-08

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

GENERICADAPTER

BRACKET

FOR INSTALLING TO PEERLESS LC MODEL ADAPTER BRACKET

For screen compatibility please refer to the LCD or plasma interface list on our website www.peerlessmounts.com or

call customer care for a screen specific adapter bracket LC or PLP models (not UL evaluated).

FOR INSTALLING TO PEERLESS PLP MODEL ADAPTER BRACKET

GENERICADAPTER

BRACKET

M5 X 6 MM OR M5 X 10 MM SCREW

M5 X 10 MM SCREW

NOTE: Refer to LC model adapter bracket instruction sheet for attachment of adapter bracket to screen.

NOTE: Either M5 x 6 mm or M5 x 10 mm screws are included with the LC model adapter bracket.

Attach hook bracket (M) to adapter bracket using four M5 x 6 mm or M5 x 10 mm screws.

NOTE: Refer to PLP model adapter bracket instruction sheet for attachment of adapter bracket to screen.

NOTE: M5 x 10 mm screws are included with the PLP model adapter bracket

Attach hook bracket (M) to adapter bracket using four M5 x 10 mm screws.

9 of 30 ISSUED: 01-27-08 SHEET #: 095-9283-2 03-18-08

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

Adjust tension knob on side of mount shown in

fig. 4.1 to desired tension to balance your screen

size and weight.

Push or pull from top or bottom of screen to adjust

tilt as shown. The tilt can be adjusted to a maximum

of 15° forward or 5° backward.

• Be careful not to pinch fingers when opening and

closing mount from the wall.

CAUTION

• Do not tighten screws with excessive force.

Overtightening can cause damage to mount. Tighten

screws to 40 in. • lb (4.5 N.M.) maximum torque.

CAUTION TENSION KNOB

fig. 4.1

4-1 Roll screen to desired position (5° clockwise or

counter-clockwise). Insert #10-32 x 1/2" flat head

phillips screw (O) to lock screen into position as

shown in figure 4.2.

fig. 4.2

To attach screen to wall mount (A), lower hook

bracket (M) with screen at an angle into pockets of

wall mount as shown in figure 3.1. Once clips are

engaged, push down to seat clips in pockets as

shown in figure 3.2. Insert and tighten M5 phillips

screw (K) to lock screen to wall mount as shown in

figure 3.3.

To remove screen from mount, loosen screw (K) and

lift screen off of mount.

Installing and Removing Flat Panel Screen

SCREEN

fig. 3.1 fig. 3.2

fig. 3.3

• Do not tighten screws with excessive force.

Overtightening can cause damage to mount. Tighten

screws to 20 in. • lb (2.26 N.M.) maximum torque.

CAUTION

• Do not lift more weight than you can handle. Use

additional man power or mechanical lifting equipment

to safely handle placement of the screen.

• Failure to lock hook bracket (M) with screw (K) can

cause screen to come off mount if hit accidentally.

WARNING POCKET

CLIP

10 of 30 ISSUED: 01-27-08 SHEET #: 095-9283-2 03-18-08

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

ARM TENSION ADJUSTMENT: If more or less tension is desired in the arm pivot points, do the following:

• To increase tension, turn tension screw(s) clockwise with allen wrench.

• To reduce tension, turn tension screw(s) counter-clockwise with allen wrench. Do not turn more than half a turn.

TENSION SCREWS

All other brand and product names are trademarks or registered trademarks of their respective owners.

• Do not remove screw or loosen screw until it is no longer engaged with the mount. Doing so may cause the

screen to fall.

WARNING

CORD

CORD MANAGEMENT: Tighten cable

to top or bottom of wall mount

assembly arm (A) using cable ties (P).

Cord Management and Arm Tension Adjustment

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels peerless-AV Support et étagère

peerless-AV

peerless-AV SMARTMOUNT STL670 Manuel utilisateur

peerless-AV

peerless-AV DS-ACC770 Mode d’emploi

peerless-AV

peerless-AV PRGS-UNV Manuel utilisateur

peerless-AV

peerless-AV STP680 Manuel utilisateur

peerless-AV

peerless-AV ACC557 Manuel utilisateur

peerless-AV

peerless-AV SR560M Manuel utilisateur

peerless-AV

peerless-AV SMARTMOUNT LT SFL670 Manuel utilisateur

peerless-AV

peerless-AV KIP749-S Manuel utilisateur

peerless-AV

peerless-AV L20PNSR780MEU Manuel utilisateur

peerless-AV

peerless-AV LCC-18 Mode d’emploi

peerless-AV

peerless-AV HF642-003 Mode d’emploi

peerless-AV

peerless-AV EST655P Manuel utilisateur

peerless-AV

peerless-AV ACCXT100 Mode d’emploi

peerless-AV

peerless-AV SA752PU Mode d’emploi

peerless-AV

peerless-AV LCH-100 Mode d’emploi

peerless-AV

peerless-AV CMJ450 Manuel utilisateur

peerless-AV

peerless-AV DCS400 Manuel utilisateur

peerless-AV

peerless-AV IM760PU Manuel utilisateur

peerless-AV

peerless-AV MOD-PRGKIT100-B Manuel utilisateur

peerless-AV

peerless-AV LCT-203 Mode d’emploi

peerless-AV

peerless-AV SUA746PU Manuel utilisateur

peerless-AV

peerless-AV ACC-SPARK70 Manuel utilisateur

peerless-AV

peerless-AV ACSBR1 Manuel utilisateur

peerless-AV

peerless-AV KIP542B Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur

peerless-AV PA740 Mode d’emploi

Manuels Support et étagère populaires d'autres marques