Patton electronics IpRocketLink 3088FR Manuel utilisateur

ipRocketLink™ Model 3088FR

G.SHDSL FRF.5/FRF.8

over ATM NTU

Quick Start Guide

Document Number: 03330U7-002 Rev. A

Part Number: 07M3088FR-QS

Revised: June 29, 2006

Sales Ofﬁce: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: [email protected]

WWW: www.patton.com

ipRocketLink 3088FR Quick Start Guide

1.0 Power up the NTU

Your NTU comes with one of the following power supply options:

•

Internal AC power supply with detachable power cord

•

External AC adaptor with detachable power cord

•

Internal DC power supply—no power accessories are included

1.1 Models with internal AC power supply

Insert the female end of the AC power cord into the internal power supply connector.

Connect the male end of the power cord into an AC power outlet (100–240 VAC).

1.2 Models with external AC adaptor

Connect female plug of the AC power cord to the AC adaptor provided.

Connect the barrel-type connector of the AC adaptor to the barrel-type power jack on the ipRocketLink.

Insert the male plug of the AC power cord into an AC power outlet (100–240 VAC)

• The ipRocketLink 3088FR contains no user serviceable parts. The

equipment shall be returned to Patton Electronics for repairs, or

repaired by qualiﬁed service personnel.

• An approved external power supply that incorporates a disconnect

device shall be used and positioned within easy reach of the operator.

• For AC powered units, the power cable used to connect the power

supply shall meet all applicable standards for the country in which it

is to be installed, and be connected to a wall outlet which has

earth ground.

• Hazardous network voltages are present in WAN ports regardless of

whether power to the unit is ON or OFF. To avoid electric shock, use

caution when near WAN ports. When detaching the cables, detach the

end away from the 3088FR ﬁrst.

• Do not work on the system or connect or disconnect cables during

periods of lightning activity.

The interconnecting cables shall be acceptable for external use and shall be rated for

the proper application with respect to voltage, current, anticipated temperature, ﬂam-

mability, and mechanical serviceability.

WARNING

CAUTION

ipRocketLink 3088FR Quick Start Guide

1.3 Models with internal DC power supply

Strip insulation 1/4-inch from the electrical wires that will connect the DC power source to

the ipRocketLink.

Connect the ground terminal from the power source to the ground terminal on the ipRocketLink.

Connect the negative (-) terminal from the power source with to the negative (-) terminal on

the ipRocketLink.

Connect the positive (+) terminal from the power source with to the positive (+) terminal on

the ipRocketLink.

1.4 Power-up indication

The

Power

LED blinks as the ipRocketLink is powering up. When the

Power

LED stops blinking and remains lit,

the ipRocketLink is ready for you to conﬁgure.

2.0 Conﬁgure the IP address

The ipRocketLink is shipped with a factory-conﬁgured IP address assigned to the

Ethernet

LAN port (green out-

line). The address is

192.168.200.10/24

. In most cases, you must change the address to be on the same subnet

as your PC, as described in the procedures below. If you are not sure which IP address to use for your installa-

tion, contact your network administrator.

2.1 Connect a PC and log in

Using the included combination RS232/Ethernet cable and DB9-RJ45 adapter, connect a PC’s serial port

to the ipRocketLink’s

Console

port (see

ﬁgure 1

Figure 1.

Connecting ipRocketLink to the PC’s Ethernet port

Start a HyperTerminal session on the PC using the settings:

9600 bps, 8 data bits, 1 stop bit, no parity, no ﬂow control

superuser

Connect to Console port

Serial port

PC with

terminal emulator

Power

Console

ipRocketLink

G.SHDSL Integrated Access Device

Model 3086

Link

CTS

DTR

WAN Sync Serial

Link

100M

TxRx

Ethernet

Status

- 511E

- Normal

- 511

Test Modes

Local -

Normal -

Remote -

ipRocketLink 3088FR Quick Start Guide

Password: superuser

2.2 Modify the IP address

Display current IP interface settings for the ipRocketLink

Ethernet

LAN port.

→→

ip list interfaces <enter>

IP Interfaces:

ID | Name | IP Address | DHCP | Transport

---|------|----------------|----------|--------------

1 | ip1 | 192.168.200.10 | disabled | <bridge>

----------------------------------------------

------

Modify the IP address for the LAN port according to your network requirements.

→→

ip set interface ip1 ipaddress 10.10.10.5 255.255.255.0

Note

The above IP address (

10.10.10.5/24)

is only an example. You must choose an IP address on the same

subnet as your PC

Verify the new address is correct and save it in system boot memory.

→→

ip list interfaces <enter>

→→

system config save <enter>

→→

3.0 Connect to the local IP network

Now you can connect the ipRocketLink to your local IP network and complete the remaining conﬁguration from

your PC using a standard web browser.

Connect the ipRocketLink’s

Ethernet

port (green) to the same Ethernet segment as your PC (see

ﬁgure 2

). The

front-panel

Ethernet Link

LED should turn on. If it does not, press the rear-panel MDI-X switch so that the

Ethernet

Link

LED illuminates.

You can check the connection with the ping command. For example shown in

ﬁgure 2

, you would ping

10.10.10.5 from a PC on the IP network.

Figure 2.

Connecting the ipRocketLink to the local IP network (Model 3088FR/RIC shown)

Crossover

10/100

Ethernet DSL

Power MDI-X

Connect to Ethernet port

Ethernet port

MDI-X switch

Interface Port

ipRocketLink 3088FR Quick Start Guide

4.0 Log onto the web management interface

You will now access the web management graphical user interface (GUI) to conﬁgure the ipRocketLink using a

standard web browser (such as Internet Explorer or Netscape browser).

At your PC, open a web browser and enter the IP address you assigned to the ipRocketLink’s Ethernet LAN

port in step 2 of section

2.2 “Modify the IP address”

on page 4.

superuser

and the password

superuser

Figure 3.

ipRocketLink web management home page

5.0 Connect the G.SHDSL Port

Obtain single-twisted-pair cable with an RJ-11 plug connector at each end.

Plug one end of the cable into the (yellow) RJ-11socket (labelled

DSL)

on the ipRocketLink Integrated

Access Device.

Plug the other end of the cable into the RJ-11 wall socket that provides your G.SHDSL service.

When a DSL link is established the front-panel

WAN LINK

LED will turn on.

6.0 Connect the serial port

Your ipRocketLink is equipped with one of the following serial WAN ports for connection to an NTU:

•

V.35 (M/34 or DB-25)—Model 3088FR/RIC/EUI

•

X.21 (DB-15)—Model 3088FR/RID/EUI

•

T1/E1(RJ-48C and dual BNC)—Model 3088FR/RIK/EUI

Connect the serial cable to the ipRocketLink serial port as follows:

Attach the male connector of the serial cable to the female serial connector on the 3088FR.

Attach the other end of the cable to the serial connector on local device’s serial port.

ipRocketLink 3088FR Quick Start Guide

Note

The NTU’s V.35 interface is wired as a DCE. No DTE conﬁguration is possible. If you are directly connect-

ing the NTU’s V.35 interface to third-party equipment that cannot be conﬁgured as a DTE, you must use

a tail-circuit cable. You can purchase a tail-circuit cable from a datacom-supply vendor. A tail-circuit

cable will cross-over the necessary V.35 signals so that the two DCE interfaces can communicate.

Note

The NTU’s X.21 interface is default conﬁgured as a DCE. Changing the DTE/DCE strap internally can set

the conﬁguration for DTE. The NTU’s X.21 interface requires a cable with a male DB-15 connector.

7.0 Additional Information

Refer to the

ipRocketLink 3086FR Getting Started Guide & 3088FR

Getting Started Guide

located on the CD-ROM

shipped with your 3088FR NTU and available online at www.patton.com/manuals for detailed information

about:

•

Installing, conﬁguring, operating, and troubleshooting,

•

Warranty, trademark, & compliance

A.0 Customer and Technical Support

Toll-Free VoIP support: call

sip:[email protected]

with a VoIP SIP phone

Online support: www

.patton.com

E-mail support:

[email protected]

—answered within 1 business day

Telephone support:

•

Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to

2200 UTC/GMT)

•

Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800

UTC/GMT)

Fax:

+1 (253) 663-5693

(USA)

or +41 (0)31 985 25 26 (

Switzerland)

ipRocketLink 3088FR Quick Start Guide

B.0 Compliance Information

B.1 Compliance

EMC Compliance:

•

FCC Part 15, Class A

•

EN55022, Class A

•

EN55024

Safety Compliance:

•

UL 609501-1/CSA C22.2 N0. 60950-1

•

IEC/EN 60950-1

•

AS/NZS 60950-1

PSTN Regulatory:

•

FCC Part 68

•

CS-03

•

TBR 12 & 13 (E1 only)

•

AS/ACIF S016:2001 (E1 only)

•

AS/ACIF SO43:2003

B.2 Radio and TV Interference (FCC Part 15)

This equipment generates and uses radio frequency energy, and if not installed and used properly—that is, in

strict accordance with the manufacturer's instructions—may cause interference to radio and television recep-

tion. This equipment has been tested and found to comply with the limits for a Class A computing device in accor-

dance with the speciﬁcations in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable

protection from such interference in a commercial installation. However, there is no guarantee that interference

will not occur in a particular installation. If the equipment causes interference to radio or television reception,

which can be determined by disconnecting the cables, try to correct the interference by one or more of the fol-

lowing measures: moving the computing equipment away from the receiver, re-orienting the receiving antenna,

and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment and

receiver are on different branches).

B.3 EC Declaration of Conformity

Product Description: ipRocketLink 3088FR

We certify that the apparatus identiﬁed above conforms to the requirements of Council Directive 1999/5/EC on

the approximation of the laws of the member states relating to Radio and Telecommunication Terminal Equip-

ment and the mutual recognition of their conformity.

8ipRocketLink 3088FR Quick Start Guide

The safety advice in the documentation accompanying this product shall be obeyed. The conformity to the above

directive is indicated by the CE sign on the device.

The signed Declaration of Conformity can be downloaded from www.patton.com/certiﬁcations/.

B.4 FCC Part 68 (ACTA) Statement

This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of

this equipment is a label that contains—among other information—a product identiﬁer in the format US:

AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

The method used to connect this equipment to the premises wiring and telephone network must comply with the

applicable FCC Part 68 rules and requirements adopted by the ACTA.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that

temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone com-

pany will notify the customer as soon as possible. Also, you will be advised of your right to ﬁle a complaint with

the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could

affect the operation of the equipment. If this happens, the telephone company will provide advance notice in

order for you to make necessary modiﬁcations to maintain uninterrupted service.

If trouble is experienced with this equipment, for repair or warranty information, please contact our company. If

the equipment is causing harm to the telephone network, the telephone company may request that you discon-

nect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public ser-

vice commission or corporation commission for information.

B.5 Industry Canada Notice

This equipment meets the applicable Industry Canada Terminal Equipment Technical Speciﬁcations. This is con-

ﬁrmed by the registration number. The abbreviation, IC, before the registration number signiﬁes that registra-

tion was performed based on a Declaration of Conformity indicating that Industry Canada technical

speciﬁcations were met. It does not imply that Industry Canada approved the equipment.

This Declaration of Conformity means that the equipment meets certain telecommunications network protective,

operational and safety requirements. The Department does not guarantee the equipment will operate to the

user’s satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to

the facilities of the local telecommunications company. The equipment must also be installed using an acceptable

method of connection. In some cases, the company’s inside wiring associated with a single line individual service

may be extended by means of a certiﬁed connector assembly (telephone extension cord). The customer should

be aware that compliance with the above condition may not prevent degradation of service in some situations.

Repairs to some certiﬁed equipment should be made by an authorized maintenance facility designated by the

supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give

the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for

The safety advises in the documentation accompanying the products shall be obeyed. The

conformity to the above directive is indicated by the CE sign on the device.

ipRocketLink 3088FR Quick Start Guide 9

their own protection that the ground connections of the power utility, telephone lines and internal metallic water

pipe system, are connected together. This protection may be particularly important in rural areas.

The information in this document is subject to change without notice. Patton Electronics assumes no

liability for errors that may appear in this document.

Trademarks statement

The term

ipRocketLink

is a trademark of Patton Electronics Company. All other trademarks presented in this doc-

ument are the property of their respective owners.

Warranty, Trademark, & Compliance Information

For warranty, trademark and compliance information, refer to the

Models 3086FR & 3088FR ipRocketLink Get-

ting Started Guide

located on the CD-ROM that came with your NTU or available online at www.patton.com.

In accordance with the requirements of council directive 2002/96/EC on Waste of

Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate

this product from other waste and scrap and deliver to the WEEE collection system in

your country for recycling.

10 ipRocketLink 3088FR Quick Start Guide

Table des matières

Autres manuels Patton electronics Matériel réseau

Patton electronics

Patton electronics 3060/X.21 Manuel utilisateur

Patton electronics

Patton electronics 2025 Manuel utilisateur

Patton electronics

Patton electronics ACC-S02 Manuel utilisateur

Patton electronics

Patton electronics 2715 Manuel utilisateur

Patton electronics

Patton electronics 2707RC Manuel utilisateur

Patton electronics

Patton electronics 2710RC Series Manuel utilisateur

Patton electronics

Patton electronics 3096RC Manuel utilisateur

Patton electronics

Patton electronics 460RC Manuel utilisateur

Patton electronics

Patton electronics 2111 Manuel utilisateur

Patton electronics

Patton electronics OnSite 9100 Manuel utilisateur

Patton electronics

Patton electronics 2500 Series Manuel utilisateur

Patton electronics

Patton electronics OnSite 07MOS10xx-GS Manuel utilisateur

Patton electronics

Patton electronics OnSite 2884 Manuel utilisateur

Patton electronics

Patton electronics ForeFront 6081RC EdgeRoute Manuel utilisateur

Patton electronics

Patton electronics ipRocketLink IAD 3086 Manuel utilisateur

Patton electronics

Patton electronics 3101RC Manuel utilisateur

Patton electronics

Patton electronics NetLink 2720 Series Manuel utilisateur

Patton electronics

Patton electronics NetLink 2720/B Manuel utilisateur

Patton electronics

Patton electronics SmartNode 4400 Manuel utilisateur

Patton electronics

Patton electronics 3324 Manuel utilisateur

Patton electronics

Patton electronics 450RC24 Manuel utilisateur

Patton electronics

Patton electronics 2888 Guide de référence

Patton electronics

Patton electronics 3002 Manuel utilisateur

Patton electronics

Patton electronics SmartNode 4400 Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur

Patton electronics ipRocketLink 3088FR Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques