Patton electronics 2707RC Manuel utilisateur

USER

MANUAL

MODEL 2707RC

NetLink-E1

E1 CSU/DSU Rack Card

SALES OFFICE

(301) 975-1000

TECHNICAL SUPPORT

(301) 975-1007

Part# 07M2707RC

Rev. C

Revised 11/11/11

An ISO-9001

Certified

Company

1.0 Warranty Information ................................................................. 4

1.1 Warranty Statement...................................................................... 4

1.2 Service Information....................................................................... 5

2.0 General Information.................................................................... 6

2.1 Features........................................................................................ 6

2.2 General Product Description......................................................... 6

3.0 Configuration .............................................................................. 7

3.1 DIP Switch Configuration.............................................................. 7

Switch S1-1 through S1-8............................................................. 8

Switch S1-1: Line Coding............................................................. 8

Switch S1-3: Line Build-out Impedance........................................ 9

S1-6 and S1-7 Clock Modes......................................................... 9

Switch S1-8: Loopback tests...................................................... 10

Switch S3: DIP switch or NMS (network management system) con-

trol............................................................................................... 10

Hardware Reset .................................................................. 10

NMS Control. ....................................................................... 10

Setting the card address. .................................................... 11

3.2 DCE/DTE selector (X.21 version only) ....................................... 12

3.3 Configuring The Rear Interface Card.......................................... 12

Model 1001RCM12548C Strap Settings .................................... 14

DTE Shield (DB-25 Pin 1) & FRGND (JB3) ......................... 15

SGND & FRGND (JB4) ....................................................... 15

Model 1001RCM13448C Strap Settings .................................... 16

DTE Shield (M/34 Pin A) & FRGND (JB3). ......................... 17

SGND & FRGND (JB4). ...................................................... 17

Model 1001RCM11548C Strap Settings .................................... 17

DTE Shield (DB-15 Pin 1) & FRGND (JB3) ......................... 18

SGND & FRGND (JB4) ....................................................... 19

Model 1001RCM11575 Strap Settings....................................... 19

4.0 Installation................................................................................. 21

4.1 The Model 1001R14 Rack Chassis............................................ 21

The Rack Power Supply............................................................. 21

Powering up Your 1001R14 Rack.............................................. 22

4.2 Installing The Model 2707RC Into The Chassis ......................... 22

4.3 Connecting to a DTE Device ...................................................... 22

4.4 Connecting to a DCE Device...................................................... 22

4.5 Connecting the E1 Interface ....................................................... 23

4.6 Connecting Dual Coax BNC (75 Ohm)....................................... 23

5.0 Operation................................................................................... 24

5.1 LED Descriptions........................................................................ 24

5.2 LOCAL LOOP DIAGNOSTICS ................................................... 25

Operating local loopback (LLB).................................................. 25

Specifications ........................................................................... 26

Cable Recommendations......................................................... 27

Factory Replacement Parts And Accessories ....................... 28

E1 Interface Pin Assignment ................................................... 29

V.35 Interface Pin Assignment ................................................ 30

EIA-530 Interface Pin Assignment .......................................... 31

X.21 Interface Pin Assignment ................................................ 32

1.0 WARRANTY INFORMATION

Thank you for your purchase of this Patton Electronics product. This

product has been thoroughly inspected and tested and is warranted for

One Year parts and labor. If any questions or problems arise during

installation or use of this product, please do not hesitate to contact Pat-

ton Electronics Technical Services at (301) 975-1007.

1.1 WARRANTY STATEMENT

Patton Electronics warrants all Model 2707RC Series components to

be free from defects, and will—at our option—repair or replace the prod-

uct should it fail within one year from the first date of shipment. This war-

ranty is limited to defects in workmanship or materials, and does not

cover customer damage, abuse, or unauthorized modification. This prod-

uct contains no serviceable parts; therefore the user shall not attempt to

modify the unit in any way. If this product fails or does not perform as

warranted, your sole recourse shall be repair or replacement as

described above. Under no condition shall Patton Electronics be liable

for any damages incurred by the use of this product. These damages

include, but are not limited to, the following: lost profits, lost savings and

incidental or consequential damages arising from the use of or inability to

use this product. Patton Electronics specifically disclaims all other war-

ranties, expressed or implied, and the installation or use of this product

shall be deemed an acceptance of these terms by the user. In the event

the user detects intermittent or continuous product malfunction due to

nearby high power transmitting radio frequency equipment, the user is

strongly advised to use only data cables with an external outer shield

bonded to a metal or metallized connector.

1.2 SERVICE INFORMATION

All warranty and non-warranty repairs must be returned freight prepaid

and insured to Patton Electronics. All returns must have a Return Materi-

als Authorization number on the outside of the shipping container. This

number may be obtained from Patton Electronics Technical Support at:

tel: (301) 975-1007

email: support@patton.com

www: http://www.patton.com

Note Packages received without an RMA number will not be

accepted.

Patton Electronics' technical staff is also available to answer any ques-

tions that might arise concerning the installation or use of your Patton

Model 2707RC. Technical Services hours: 8AM to 5PM EST, Monday

through Friday.

2.0 GENERAL INFORMATION

Thank you for your purchase of this Patton Electronics product. This prod-

uct has been thoroughly inspected and tested and is warranted for One

Year parts and labor. If any questions arise during installation or use of the

unit, contact Patton Electronics Technical Services at (301) 975-1007.

2.1 FEATURES

• Terminates E1/G.703 circuits over a 4-wire RJ-48C interface

• Connects to standard CPE serial and 10Base-T interfaces

• Unstructured rate of 2.048 Mbps (G.703)

• Selectable AMI or HDB3 line coding

• Configuration via internal DIP switches or SNMP management of local

unit through the 1001MC

• Six easy-to-read LED indicators monitor data and diagnostics

• Internal, external, network clocking

• also operates as a high-speed point-to-point modem

• Fits into Patton’s 2U rack-mount chassis

• Made in USA

• Conforms to ONP requirement CTR12 for connection to international

telecom networks

2.2 GENERAL PRODUCT DESCRIPTION

The Model 2707RC Series are single port E1 CSU/DSUs that provide

high-speed WAN connectivity in a rack card package. Connecting to the

serial WAN port of a switch, router or multiplexer, the NetLink-E1™ pro-

vides E1 access connection at data rates of 2.048 Mbps. The NetLink-

E1™ is an excellent choice when terminating leased line services, Frame

Relay backbones, internet access as well as LAN-to-LAN services.

The Netlink-E1™ provides digital access to local WAN services between

two facilities over a dedicated 4-Wire circuit. Clock modes, line imped-

ance, and coding options are programmed via internally accessible DIP

switches or SNMP manageable through the 1001MC. The Netlink-E1™

uses AMI and HDB3 line coding. Netlink-E1™ also supports a full range

of system and diagnostic features that make system setup easy.

The NetLink-E1 provides E1 terminations over a modular RJ-48C jack or

dual 75 Ohm BNC connectors when using the 1001RCM11575 (X.21)

rear card.

3.0 CONFIGURATION

The 2707RC features configuration capability via hardware DIP switches

or SNMP through Patton’s Model 1001MC Management Card. This sec-

tion describes all possible hardware and software switch configurations

of the network connection.

Note The 2707RC factory default is set to DIP switch control. Soft-

ware control can be enabled by setting S3 to a valid address

SNMP management station. Performing a hardware reset sets

the unit for dip switch control.

3.1 DIP SWITCH CONFIGURATION

The Model 2707RC has two eight bit DIP switches that allow configura-

tion for a wide range of applications. The switches are accessed by

removing the card from the chassis.Figure 1 shows the location of the

DIP switches on the top of the printed circuit board.

Figure 1. Model 2707RC Series top view, showing location of DIP switches.

DIP Switches S1 and S3 can be configured as either “On” or “Off”.

Figure 2 shows the orientation of the DIP switches with respect to ON/

OFF positions. Default position and descriptions for Switches S1 and S3

are provided on the next page.

S3 S1

12345678

Figure 2. Close up of DIP switches showing ON/OFF positions.

Note If you do not have a terminal, you may force the unit to use the

DIP switches as the default configuration source by turning off

the unit, setting all the DIP switches to the ON position, then

powering on the unit. This will cause the unit to enter a special

mode. Then turn off the unit and change the switch settings to

the desired settings. When you turn the unit on again, the unit

will be set up with the selected switch settings.

Switch S1-1 through S1-8

A detailed description of each switch (S1-1 through S1-8) setting follows

the summary table below.

Switch S1-1: Line Coding

Use switch S1-1 to control the network line coding. Set these options to

be the same as the line coding given to you by your service provider. If

Table 1: Switch Set 1 Summary

Position Function Factory Default Selected

Option

S1-1 Line Coding OFF HDB3

S1-2 Reserved OFF

S1-3 Line Build Out OFF 120 ohm

S1-4 Reserved OFF

S1-5 Reserved OFF

S1-6 Clocking Mode OFF Network

S1-7 Clocking Mode OFF Network

S1-8 TM from DTE OFF Enabled

you are using two Model 2707s together as short-range modems, set

both units to HDB3.

Switch S1-3: Line Build-out Impedance

Switch S1-3 is used to select line build-out (LBO) impedance for the Model

2707’s E1 port. Your Model 2707RC comes equipped with either an RJ-48C

connector, dual BNC connectors, or both. When connecting to the E1 net-

work, the LBO selection must match the connector type. If the dual BNC con-

nectors are used, the line build-out impedance must be set to 75-ohm.

Otherwise, for the RJ-48C connector, impedance should be set to 120 ohm.

S1-6 and S1-7 Clock Modes

Set switch S1-6 and S1-7 to determine the 2707RC’s transmitter timing.

Table 2: S1-1 Line Coding settings

S1-1 Line Coding

Off HDB3

On AMI

Table 3: S1-3 Line Build-out settings

S1-3 Setting

75 ohm On

120 ohm Off

Table 4: S1-6 and S1-7 Clock Modes

S1-6 S1-7 Clock Mode

On On Network (Received Recovered)

On Off Internal

Off On External

Off Off Network (Received Recovered)

Network Clock Transmitter timing is derived using the received

line signal (received recovered) from the network.

Internal Clock Transmitter timing is derived from an internal clock

source.

External Clock Transmitter timing is derived from DTE terminal

timing. (Units equipped with 10Base-T modules do

not operate in external clock mode. They enter

internal clock mode when this setting is selected.)

Switch S1-8: Loopback tests

Use switch S1-8 to allow the Model 2707RC to enter loopbact test mode

when the DTE raises the appropriate loop request pin.

Switch S3: DIP switch or NMS (network management system) control

The Model 2707RC can be configured and managed via DIP switches, or

NMS-SNMP/HTTP through a Patton Model 1001MC management card

acting as a proxy agent. (refer to the 1001MC user manual when using

this mode). Switch S3 selects control and management mode for the

Model 2707RC.

Hardware Reset . The Model 2707RC isset at the factory for DIP switch

control. If the user has changed control to NMS, and then needs to revert

to DIP switch control, use the following procedure:

1. Pull the Model 2707RC out of the rack.

2. Set all switches (S1 and S3) to the ON position.

3. Install the card into the rack and power up the unit.

4. Pull the card out again and change the switches to the desired set-

tings. The unit is now under DIP switch control.

5. Install the card back into the rack.

NMS Control. When switches S3-1 to S3-8 are set to a setting other

than the ones shown in Table 6, the Model 2707RC enters NMS control.

While under NMS control, each of the Model 2707RC cards housed in a

rack must have an address. Table 7 and Figure 3 show examples of

address settings. The table follows the hexadecimal system, where

switch SW3-1 is the least significant bit (LSB), and SW3-8 is the most

Table 5: S1-8 Loopback test settings

S1-8 Setting

Off DTE loopback request enabled

On DTE loopback request disabled

Table 6: S3 DIP switch settings

S3-1 to S3-8 Management selection

All set to Off DIP switch control (factory default)

All set to On Hardware reset

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Patton electronics Matériel réseau

Patton electronics

Patton electronics ACC-S02 Manuel utilisateur

Patton electronics

Patton electronics 460RC Manuel utilisateur

Patton electronics

Patton electronics FORESIGHT 6300 Manuel utilisateur

Patton electronics

Patton electronics SMARTNODE 4900 Manuel utilisateur

Patton electronics

Patton electronics OnSite 1052 Series Manuel utilisateur

Patton electronics

Patton electronics NetLink 2701/B Manuel utilisateur

Patton electronics

Patton electronics 2888 Manuel utilisateur

Patton electronics

Patton electronics 2450 Manuel utilisateur

Patton electronics

Patton electronics 1084 Manuel utilisateur

Patton electronics

Patton electronics SmartNode 4654 Series Manuel utilisateur

Patton electronics

Patton electronics 3095 Manuel utilisateur

Patton electronics

Patton electronics 2111 Manuel utilisateur

Patton electronics

Patton electronics NetLink 2720 Series Manuel utilisateur

Patton electronics

Patton electronics 3004 ECB Series Manuel utilisateur

Patton electronics

Patton electronics ForeFront 2616RC Manuel utilisateur

Patton electronics

Patton electronics RocketLink-G 3088/I Manuel utilisateur

Patton electronics

Patton electronics 593/45 Manuel utilisateur

Patton electronics

Patton electronics 2450 Manuel utilisateur

Patton electronics

Patton electronics NetLink 2960 RAS Manuel utilisateur

Patton electronics

Patton electronics 2120 Manuel utilisateur

Patton electronics

Patton electronics NetLink 2720 Series Manuel utilisateur

Patton electronics

Patton electronics NetLink 2707C Manuel utilisateur

Patton electronics

Patton electronics Diamond Edge 3224 Manuel utilisateur

Patton electronics

Patton electronics SL402X Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur