Patton electronics 1092 Manuel utilisateur

USER

MANUAL

MODEL 1092

High Speed, 2-Wire,

Sync & Async

Short Range Modem

SALES OFFICE

(301) 975-1000

TECHNICAL SUPPORT

(301) 975-1007

http://www.patton.com

Part# 07M1092-F

Doc# 033011U, Rev. G

Revised 1/23/08

&(57,),('

$Q,62

&HUWLILHG&RPSDQ\

TABLE OF CONTENTS

Section Page

1.0 Warranty Information .............................................................2

1.1 Radio and TV Interference

1.2. CE Notice

1.3 Service Information

2.0 General Information...............................................................4

2.1 Features

2.2 Description

3.0 Configuration .........................................................................5

3.1 Configuring the Hardware DIP Switches

3.1.1 Configuration Switch Set “S1”

3.1.2 Configuration Switch Set “S2”

3.2 Configuring the Software Switches

3.2.1 Configuring the Local 1092

3.2.2 Configuring the Remote 1092

3.3 Power Connection

4.0 Installation ...........................................................................21

4.1 Connecting the Twisted Pair Interface

4.2 Connecting the Serial Port

4.2.1 Changing

QuikConnect™

Modules

4.2.2 Connecting a “DTE” Device

4.2.3 Connecting a “DCE” Device

4.2.4 Configuring the X.21

QuikConnect™

Module

4.3 Connecting Power

4.3 Control Port Interface

Connecting to an AC Power Source

Connecting to a DC Power Source

5.0 Operation.............................................................................26

5.1 Power- Up

5.2 LED Status Monitors

5.3 Test Modes

5.3.1 Using Local Line Loopback (LLB)

5.3.2 Using Remote Digital Loopback (RDL)

5.3.3 Using the V.52 (BER) Test Pattern Generator

Appendix A - Specifications ........................................................30

Appendix B - Factory Replacement Parts and Accessories .......31

Appendix C - Interface Pin Assignments ....................................33

Appendix D - Control Port Pin assignments ...............................35

1.0 WARRANTY INFORMATION

Patton Electronics warrants all Model 1092 components to be

free from defects, and will—at our option—repair or replace the product

should it fail within one year from the first date of shipment.

This warranty is limited to defects in workmanship or materials,

and does not cover customer damage, abuse or unauthorized

modification. If this product fails or does not perform as warranted,

your sole recourse shall be repair or replacement as described above.

Under no condition shall Patton Electronics be liable for any damages

incurred by the use of this product. These damages include, but are

not limited to, the following: lost profits, lost savings and incidental or

consequential damages arising from the use of or inability to use this

product. Patton Electronics specifically disclaims all other warranties,

expressed or implied, and the installation or use of this product shall be

deemed an acceptance of these terms by the user.

1.1 RADIO AND TV INTERFERENCE

The Model 1092 generates and uses radio frequency energy, and

if not installed and used properly—that is, in strict accordance with the

manufacturer's instructions—may cause interference to radio and

television reception. The Model 1092 has been tested and found to

comply with the limits for a Class A computing device in accordance

with the specifications in Subpart J of Part 15 of FCC rules, which are

designed to provide reasonable protection from such interference in a

commercial installation. However, there is no guarantee that

interference will not occur in a particular installation. If the Model 1092

does cause interference to radio or television reception, which can be

determined by disconnecting the unit, the user is encouraged to try to

correct the interference by one or more of the following measures:

moving the computing equipment away from the receiver, re-orienting

the receiving antenna and/or plugging the receiving equipment into a

different AC outlet (such that the computing equipment and receiver are

on different branches).

1.2 CE NOTICE

The CE symbol on your Patton Electronics equipment indicates

that it is in compliance with the Electromagnetic Compatibility (EMC)

directive and the Low Voltage Directive (LVD) of the European Union

(EU). A Certificate of Compliance is available by contacting Technical

Support.