Paradyne 4000E Manuel utilisateur
IPD4-A2-GZ40-10 July 2005 1
4000E IP Broadband Loop Carrier
Installation Instructions
Document Number IPD4-A2-GZ40-10
July 2005
Contents
Software and Firmware License Agreement ...................................................... 1
Introduction ........................................................................................................ 3
Unpacking and Inspecting the Equipment ......................................................... 3
Installation Options ............................................................................................ 4
Installing Your Management Module .................................................................. 6
Installing Your Interface Module(s) ..................................................................... 7
Powering Up Your 4000E BLC ........................................................................... 9
Uplink Connections ............................................................................................ 12
Subscriber Lines ................................................................................................ 12
Securing the Connecting Cables ....................................................................... 15
Configuration and Management ........................................................................ 15
Fan Module ........................................................................................................ 16
Specifications ..................................................................................................... 17
Product Documentation Online .......................................................................... 17
Important Safety Instructions ............................................................................. 18
Warranty, Sales, Service, and Training Information ........................................... 20
Software and Firmware License Agreement
The terms and conditions of this License Agreement (the “Agreement”) will apply
to the software and/or firmware (individually or collectively the “Software”)
incorporated into the Paradyne product (the “Product”) purchased by you and any
ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS
TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED
INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU
SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.
IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS
LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS
ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE
LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE
LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU
WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT
PURCHASED BY YOU.
2July 2005 IPD4-A2-GZ40-10
derivatives obtained from the Software, including any copy of either. If you have
executed a separate written agreement covering the Software supplied to you
under this purchase, such separate written agreement shall govern.
Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to
accept a personal, non-transferable, non-exclusive, right (without the right to
sublicense) to use the Software, solely as it is intended and solely as incorporated
in the Product purchased from Paradyne or its authorized distributor or reseller
under the following terms and conditions:
1. Ownership: The Software is the sole property of Paradyne and/or its licensors.
The Licensee acquires no title, right or interest in the Software other than the
license granted under this Agreement.
2. Licensee shall not use the Software in any country other than the country in
which the Product was rightfully purchased except upon prior written notice to
Paradyne and an agreement in writing to additional terms.
3. The Licensee shall not reverse engineer, decompile or disassemble the
Software in whole or in part.
4. The Licensee shall not copy the Software except for a single archival copy.
5. Except for the Product warranty contained in the manual, the Software is
provided “AS IS” and in its present state and condition and Paradyne makes
no other warranty whatsoever with respect to the Product purchased by you.
THIS AGREEMENT EXPRESSLY EXCLUDES ALL OTHER WARRANTIES,
WHETHER EXPRESS OR IMPLIED, OR ORAL OR WRITTEN, INCLUDING
WITHOUT LIMITATION:
a. Any warranty that the Software is error-free, will operate uninterrupted in
your operating environment, or is compatible with any equipment or
software configurations; and
b. ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
Some states or other jurisdictions do not allow the exclusion of implied
warranties on limitations on how long an implied warranty lasts, so the above
limitations may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from one state or jurisdiction to
another.
6. In no event will Paradyne be liable to Licensee for any consequential,
incidental, punitive or special damages, including any lost profits or lost
savings, loss of business information or business interruption or other
pecuniary loss arising out of the use or inability to use the Software, whether
based on contract, tort, warranty or other legal or equitable grounds, even if
Paradyne has been advised of the possibility of such damages, or for any
claim by any third party.
7. The rights granted under this Agreement may not be assigned, sublicensed or
otherwise transferred by the Licensee to any third party without the prior
written consent of Paradyne.
8. This Agreement and the license granted under this Agreement shall be
terminated in the event of breach by the Licensee of any provisions of this
Agreement.
IPD4-A2-GZ40-10 July 2005 3
9. Upon such termination, the Licensee shall refrain from any further use of the
Software and destroy the original and all copies of the Software in the
possession of Licensee together with all documentation and related materials.
10. This Agreement shall be governed by the laws of the State of Florida, without
regard to its provisions concerning conflicts of laws.
Introduction
Paradyne's 4000E IP Broadband Loop Carrier (BLC) provides a high capacity and
native IP Ethernet foundation for a variety of feature-rich multi-service access
mulitplexer modules.
The 4000E BLC features a high capacity backplane delivering up to 8 Gbps
throughput, and providing a non-blocking architecture for even the highest
bandwidth broadband access technologies, such as ADSL2+. It supports a single
uplink, management, and switching module connected to the dual backplanes with
redundant modular backhaul/uplink ports to support 10/100 Ethernet, GigE
(copper or fiber), T1/E1, and dual bonded T1/E1 uplink modules.
The 4000E BLC is environmentally hardened for installation in Remote Terminals
or street cabinets. For flexibility of installation the 4000E BLC has removable
mounting brackets that can be placed in increments of 1.45” up to 9.28” from the
front of the chassis, allowing for multiple installation options in either 19" or 23"
equipment racks.
Unpacking and Inspecting the Equipment
HANDLING PRECAUTIONS FOR
STATIC-SENSITIVE DEVICES
This product is designed to protect sensitive components from damage
due to electrostatic discharge (ESD) during normal operation. When
performing installation procedures, however, take proper static control
precautions to prevent damage to equipment. If you are not sure of the
proper static control precautions, contact your nearest sales or service
representative.
The following components should be included in the shipping container:
1 – 4000E BLC with 1 fan module and 12 slot covers
4 – Rubber Bumper Screws
!
4July 2005 IPD4-A2-GZ40-10
2 – Rack Mount Brackets (either 19" or 23", as ordered)
10 – #6 Phillips Bracket Screws
8 – #10 Phillips Rack Screws
8 – #12 Phillips Rack Screws
If there is visible damage, do not attempt to connect the device. Contact your sales
representative.
Installation Options
The 4000E BLC is designed for installation in a Restricted Access area where
admittance is limited to trained and authorized service personel. It may be
installed on a tabletop or in a rack.
Installation on a Tabletop
Insert the four provided rubber bumper screws into the mounting holes at the
bottom of the 4000E chassis for surface grip and airflow. Position and secure all
connecting cables such that they will not become a tripping hazard or pull loose
from the chassis. Ensure that the air supply vents around the top and bottom
edges of the chassis are not blocked.
4000E BOTTOM VIEW
RUBBER BUMPER
SCREW
Side Top
Front Rear
IPD4-A2-GZ40-10 July 2005 5
Installation in a Rack
Using a Phillips Screwdriver, attach the two [2] provided rack mount brackets to the
sides of the 4000E with eight [8] of the ten [10] provided bracket screws. There are
seven position options for the rack brackets; position them as best suited to the
space available for your chassis on the rack being utilized.
Mount the chassis onto the rack and secure the rack mount brackets to the sides
of the rack using one of the two provided sets of eight [8] rack screws (whichever
size fits the rack being utilized).
Check the rack for stability, ensuring that installation of the 4000E has not caused
the rack to become top-heavy.
RACK MOUNT
BRACKET 4000E SIDE VIEW
Front Rear
4000E FRONT VIEW
6July 2005 IPD4-A2-GZ40-10
Installing Your Management Module
A management module provides the functional control for the 4000E BLC; the
4000E cannot function without one. There are several different models available
for purchase. Refer to www.paradyne.com for further information, or contact your
sales representative.
Installing a Management Module
An uplink module provides the upstream network connection for the 4000E BLC; a
management module cannot function without one. Depending on the management
module model that you plan to install in your 4000E, you will need either a Media
Interface Module (MIM) or an Uplink Interface Module (UIM). Only one uplink
module is required for operational purposes. However, two uplink modules may be
installed, one in each port of the management module, if redundancy is desired.
Refer to your management module or uplink module installation instructions for
further information.
CAUTION
If a slot cover is removed from a management module uplink port, it must be
replaced with an uplink module. DO NOT OPERATE A 4000E WITH A
MANAGEMENT MODULE THAT HAS AN OPEN UPLINK PORT.
Procedure
1. Identify the appropriate slot for installation.
The 4000E is a five slot chassis: slots 1–4 are reserved for interface modules
and Slot U1 is reserved for a management module. The 4000E is shipped
from the factory with slots 1 and U1 open and ready for module installation.
2. Align the management module with the slot module guides. With the
management module printed circuit board (PCB) facing up and the
management module model name on the right side of the module faceplate
(facing towards you), align the left and right edges of the PCB with the U1 slot
module guides on the 4000E.
Management Module Slot
IPD4-A2-GZ40-10 July 2005 7
3. Slide the Management Module Firmly into the Chassis. Tighten the fastening
screws on the management module faceplate.
Installing Your Interface Module(s)
Interface modules provide the subscriber connections for a 4000E BLC; up to four
interface modules may be installed in the 4000E (in slots 1–4). There are a variety
of models available for purchase. Refer to www.paradyne.com for further
information or contact your sales representative. Any combination of interface
module models may be installed in an 4000E as long as they are supported by the
model type and version number of your management module; refer to the Release
Notes for your particular management module model.
CAUTION
If a slot cover is removed from slots 2–4, it must be replaced with an uplink
module. DO NOT OPERATE A 4000E WITH AN EMPTY MODULE SLOT.
MANAGEMENT MODULE
Slot Module Guides
Fastening Screws
8July 2005 IPD4-A2-GZ40-10
Procedure
1. Select a Slot for Installation.
Although the 4000E is factory shipped with Slot 1 open, interface modules
may be installed in any slot, 1–4.
2. Align the interface module with the slot module guides. With the interface
module PCB facing up and the interface module model name on the right side
of the module faceplate (facing towards you), align the left and right edges of
the PCB with the slot module guides of the chosen slot on the 4000E.
3. Slide the interface module fFirmly into the chassis. Tighten the fastening
screws on the interface module faceplate.
Slot Module Guides
INTERFACE MODULE
Fastening Screws
IPD4-A2-GZ40-10 July 2005 9
Powering Up Your 4000E BLC
CAUTION:
Turn your DC power source(s) OFF until you have completed connection of
the 4000E as outlined in the following sections.
Do not operate the 4000E without a ground connection.
Procedure
1. Connect a ground wire to the 4000E: Line up the 2-hole terminal lug of your
ground wire with the two holes on the small, unpainted section on the back of
your chassis. Secure the terminal lug to the chassis with two #10-32 screws.
2. Connect the Ground Wire to a Frame Ground. Ground wire connection can
vary from location to location, although typically all equipment in a Central
Office is grounded to a common copper bus.
3. Select a Terminal Block. Either terminal block on the back of the 4000E may
be used to power the chassis; only one terminal block is required for
operational purposes. The two terminal blocks on the 4000E are independent
feeds. Chassis power is supplied by only one terminal block at a time; the
second supply is a backup. The two terminal blocks do not load-share; each
terminal block must be supplied with adequate amperage to run the chassis
independently.
4000E REAR VIEW
Ground Connection for 2-Hole Terminal Lug
10 July 2005 IPD4-A2-GZ40-10
4. Select a terminal block. Using a Phillips Screwdriver, remove the upper screw
from the chosen terminal block (labeled "+" on the chassis). Slide the ring
terminal of your positive power lead around the shaft of the screw and insert
the screw into the same "+" terminal from which it was removed.
DC Terminal Blocks
Ring
Terminal
POSITIVE
POWER LEAD
DC POWER
TERMINAL
Positive (+)
Terminal
Table des matières
Autres manuels Paradyne Matériel réseau
Paradyne
Paradyne ACCULINK 3160 Manuel utilisateur
Paradyne
Paradyne Hotwire 5446 Manuel utilisateur
Paradyne
Paradyne Jetstream CPX-1000 Manuel utilisateur
Paradyne
Paradyne GranDSLAM 4200 Manuel utilisateur
Paradyne
Paradyne 7986 Manuel utilisateur
Paradyne
Paradyne 8310 MVLt Manuel utilisateur
Paradyne
Paradyne COMSPHERE 3810 Manuel utilisateur
Paradyne
Paradyne COMSPHERE 6700 Series Manuel utilisateur
Paradyne
Paradyne 7511 Manuel utilisateur
Paradyne
Paradyne COMSPHERE 6700 Series Manuel utilisateur
Paradyne
Paradyne COMSPHERE 3610 Manuel
Paradyne
Paradyne COMSPHERE 3550 Series Manuel utilisateur
Paradyne
Paradyne iMarc SLV 9820-2M Manuel utilisateur
Paradyne
Paradyne COMSPHERE 6700 Series Manuel utilisateur
Paradyne
Paradyne 7510 DSU Manuel d'installation
Paradyne
Paradyne 7110 Guide rapide
Paradyne
Paradyne JetFusion Integrated Access Device Manuel utilisateur
Paradyne
Paradyne Jetstream CPX-1000 Manuel utilisateur
Paradyne
Paradyne COMSPHERE 6700 Series Manuel utilisateur
Paradyne
Paradyne Hotwire 5446 Manuel utilisateur
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
