Panasonic ET-MDNHM10C Manuel utilisateur
Read before use
The “Operating Instructions” explains about the interface boards to be
installed to a Panasonic display device (projector or at panel display).
For Model No. and model names, refer to the product list (x page 5).
Thank you for purchasing this Panasonic product.
■Before using this product, please read these “Operating Instructions” and
the “Operating Instructions” of the display device carefully and save the
manuals for future use.
■Before using this product, be sure to read “Read this rst!” (x pages 3 to 4).
TQZJ730-3
Printed in China
Interface Board Commercial Use
Operating Instructions
ENGLISH
Model No. ET-MDNHM10C
ET-MDNDV10C
* The illustration above is an example. In this manual, illustrations of ET-MDNHM10C
are used as an example unless otherwise specied.
2 - ENGLISH
Contents
Contents
Read this rst! 3
Precautions for use 5
Products list 5
Supported display device 5
About the handling of the product 5
Disposal 6
Accessories 6
Part names and functions 6
Installing the Interface Board 8
Before installing or removing the Interface Board 8
How to install the Interface Board 9
How to remove the Interface Board 10
Specications 11
rTrademarks
fThe terms HDMI and HDMI High-Denition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing
Administrator, Inc. in the United States and other countries.
ENGLISH - 3
Read this rst!
Read this rst!
WARNING:
Do not spill water on this product or allow this product to get wet.
Doing so may cause re, electric shock, or malfunction due to short circuit
or overheating.
fDo not place a container with liquid close to this product.
fConsult your dealer when liquid such as water is spilled on this
product.
Do not place the supplied screws in a location that a child can reach.
Accidentally swallowing them can cause a physical harm.
fSeek a medical advice immediately if a child might have swallowed a
screw.
Do not disassemble or modify.
Doing so may cause electric shock or re. It may also cause a malfunction.
Ask the qualied technician or your dealer to install or remove this
product to/from the at panel display.
Failure to do so may cause electric shock. It may also cause a
malfunction.
Turn o the power and disconnect the power plug from the outlet
when installing or removing this product to/from the at panel
display.
Failure to do so may cause electric shock.
CAUTION:
Do not place this product in a location with excessive humidity or
dust, or in a location exposed to oil smoke or steam.
Doing so may cause re or electric shock.
Do not place this product in extremely hot location.
Doing so may deteriorate the part, or may cause re.
fDo not install or store in a location with direct sunlight or close to the
heating device, etc.
Turn o the power and disconnect the power plug from the outlet
when installing or removing this product to/from the projector.
Failure to do so may cause electric shock.
4 - ENGLISH
Read this rst!
Name and quantity of hazardous substances contained in the
product
Parts Hazardous substances
Pb Hg Cd Cr VI PBB PBDE
Printed circuit boards
(PCB)
Accessories
This table is prepared in accordance with the provisions of SJ/T 11364.
: The amount of hazardous substances included in all homogeneous
materials for the relevant part does not exceed the limit specied in GB/T
26572.
: The amount of hazardous substances included in all homogeneous
materials for the relevant part exceeds the limit specied in GB/T 26572.
Precautions for use
ENGLISH - 5
Precautions for use
Products list
The product names and their Model Nos. described in this document are as
follows.
Product name Product Model No. Remark
Interface Board for HDMI
2 input ET-MDNHM10C An Interface Board equipped with 2
HDMI inputs.
Interface Board for DVI-D
2 input ET-MDNDV10C An Interface Board equipped with 2
DVI-D inputs.
Supported display device
The display device (projector or at panel display) supported by the Interface
Board described in this document is as follows.
(As of March 2019)
Projector PT-SRQ13KC, PT-SRQ32KC, PT-SRQ22KC
Flat panel display (Support to be determined)
Note
fThe model not described in the table may also be supported. Refer to the Operating
Instructions of your display device.
About the handling of the product
rDo not touch the connector section of the Interface Board
directly with your hands.
The component may be damaged by the static electricity. Handle this
product after removing the static in your body by touching the surrounding
metal, etc.
rAsk a qualied technician to install or remove to/from the at
panel display.
There is a danger of electric shock or a malfunction may occur due to static
electricity. Consult your dealer.
Precautions for use
6 - ENGLISH
Disposal
To dispose of the product, ask your local authorities or dealer for correct
methods of disposal.
Accessories
Make sure that the following accessories are provided with your product.
Numbers enclosed in < > show the number of accessories.
Screw <4>
(XSB3+8FN)
Attention
fAppropriately discard the packaging material after unpacking the product.
fFor missing accessories, consult your dealer.
fStore small parts in an appropriate manner, and keep them away from small children.
Note
fThe supplied screws are spare. Use them when a screw to x the slot cover of the display
device is lost.
fThe model numbers of accessories are subject to change without prior notice.
Part names and functions
rInterface Board for HDMI 2 input (Model No.: ET-MDNHM10C)
13 32
1 <HDMI 输入 1> terminal (when
installed in <SLOT 1> of the display
device), <HDMI 输入 3> terminal
(when installed in <SLOT 2> of the
display device)
This is a terminal to input the HDMI
signal.
2 <HDMI 输入 2> terminal (when
installed in <SLOT 1> of the display
device), <HDMI 输入 4> terminal
(when installed in <SLOT 2> of the
display device)
This is a terminal to input the HDMI
signal.
3 Handle
Precautions for use
ENGLISH - 7
rInterface Board for DVI-D 2 input (Model No.: ET-MDNDV10C)
13 32
1 <DVI-D 输入 1> terminal (when
installed in <SLOT 1> of the display
device), <DVI-D 输入 3> terminal
(when installed in <SLOT 2> of the
display device)
This is a terminal to input the DVI-D
signal.
2 <DVI-D 输入 2> terminal (when
installed in <SLOT 1> of the display
device), <DVI-D 输入 4> terminal
(when installed in <SLOT 2> of the
display device)
This is a terminal to input the DVI-D
signal.
3 Handle
Installing the Interface Board
8 - ENGLISH
Installing the Interface Board
It is recommended to ask a qualied technician to install or remove the
Interface Board to a projector. A malfunction may occur due to static
electricity. Consult your dealer.
Ask a qualied technician to install or remove the Interface Board to/from a
at panel display. There is a danger of electric shock or a malfunction may
occur due to static electricity. Consult your dealer.
Before installing or removing the Interface Board
fAlways turn o the power of the display device (projector or at panel
display) before installing or removing the Interface Board.
gMake sure to follow the procedure described in the Operating
Instructions of your display device when turning o the power.
fDo not touch the connector section of the Interface Board directly with your
hands.
gThe component may be damaged by the static electricity.
fRemove the static charge from your body by touching the surrounding
metal, etc., in advance to prevent the static electricity damage.
fTake care not to get injured when installing or removing the Interface
Board.
gHands may be injured by the opening of the blank slot of the display
device or the edge of the bracket of the Interface Board.
fWhen installing the Interface Board to the slot, insert it into the connector
straight and slowly.
gIt may not operate or cause malfunction if it is not correctly installed.
fThe gure indicating the installation and removal of the Interface Board is
using the combination of the Interface Board for HDMI 2 input (Model No.:
ET-MDNHM10C) and the optional projector (Model No.: PT-SRQ13KC) as
an example. Illustration of this document may vary from the actual product.
fThe details of the installation or removal may be dierent depending on the
display device, so conrm the Operating Instructions of your display device
too.
Installing the Interface Board
ENGLISH - 9
How to install the Interface Board
Screws (4 locations) Screws (4 locations)Salient
Guide grooveSlot cover
Fig. 1 Fig. 2 Fig. 3
1) Remove the slot cover. (Fig. 1)
fRemove the four screws xing the slot cover of the display by rotating
counterclockwise with a Phillips screwdriver. The removed screws are
used to x the Interface Board.
fWhen removing the fourth screw, hold the slot cover with your hand so
it will not fall.
fTo replace from other Interface Board, remove the Interface Board
following the procedure in “How to remove the Interface Board”
(x page 10).
2) Install the Interface Board to the display device. (Fig. 2)
fInsert the guide groove of the Interface Board aligned to the salient of
the slot. Insert the bracket rmly all the way in.
3) Fix the Interface Board. (Fig. 3)
fTighten and x with the four screws removed in Step 1).
Attention
fThe removed slot cover is required when the unnecessary Interface Board is removed. Store
it so it can be attached in the future.
Installing the Interface Board
10 - ENGLISH
How to remove the Interface Board
Handle
Fig. 1
1) Remove the Interface Board. (Fig. 1)
fRemove the four screws xing the Interface Board by rotating
counterclockwise with a Phillips screwdriver. The removed screws are
used to x the slot cover.
fHold the handle of the Interface Board and remove it slowly.
2) Attach the slot cover.
fAttach the stored slot cover to the blank slot, and tighten and x with
the four screws removed in Step 1).
fTo replace with other Interface Board, attach the Interface Board
following the procedure in “How to install the Interface Board”
(x page 9).
Attention
fAlways attach the slot cover on the blank slot.
fStore the removed Interface Board inside an antistatic bag.
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Panasonic Matériel informatique
Panasonic
Panasonic FP7 Series Manuel utilisateur
Panasonic
Panasonic Future Electronics BULLSEYE Manuel utilisateur
Panasonic
Panasonic MICROCOMPUTER MN103S Manuel utilisateur
Panasonic
Panasonic 2SC1318A Manuel utilisateur
Panasonic
Panasonic MALT062HG Manuel utilisateur
Panasonic
Panasonic WJMPU955A - CENTRAL PROCESSING UNIT Manuel utilisateur
Panasonic
Panasonic AJ-YAD455 Manuel utilisateur
Panasonic
Panasonic AV-HS04M7D Manuel utilisateur
Panasonic
Panasonic CF-BAB2048U Manuel utilisateur
Panasonic
Panasonic TY-42TM6B - Monitor Terminal Expansion Board Guide de l'utilisateur
Panasonic
Panasonic TY-SB01DL Manuel utilisateur
Panasonic
Panasonic FP7 Series Manuel utilisateur
Panasonic
Panasonic AV-HS04M2 Manuel utilisateur
Panasonic
Panasonic 2SA2078 Manuel utilisateur
Panasonic
Panasonic WZ-AESDA Manuel utilisateur
Panasonic
Panasonic AJ-PCD35P Manuel utilisateur
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Panasonic
Panasonic CF-BAM1024U Manuel utilisateur
Panasonic
Panasonic CF-BAK0512U Manuel utilisateur
Panasonic
Panasonic ET-MDNDP10C Manuel utilisateur
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
Hauppauge
Hauppauge WinTV-HVR-2250 Manuel utilisateur
