OWC U.2 SHUTTLE Mode d’emploi

U.2 SHUTTLE

3.5-inch U.2 NVMe SSD Carrier Shuttle

Ideal for Media Production Workows

Ooad day’s shoot and send drive to post

Fast and Easy Drive Swaps

Move between U.2 devices,

PCs, and servers

RAID Ready

Harness the power of RAID 0, 1, 4, 5, or 10

via your choice of RAID utilities

TABLE OF CONTENTS

INTRODUCTION

1.1 Minimum System Requirements .................................................................... 3

1.2 Packaging Contents ........................................................................................ 3

1.3 About This Manual........................................................................................... 3

DEVICE SETUP

2.1 Installation of M.2 Drive(s).............................................................................. 4

2.2 Host Installation: Helios 3S with U.2 NVMe Interchange System ...............5

2.3 Host Installation: ThunderBay Flex 8 ............................................................. 6

2.4 Host Installation: Mercury Pro U.2 Dual ......................................................... 7

2.5 Usage Notes..................................................................................................... 8

SUPPORT RESOURCES

3.1 Troubleshooting............................................................................................... 9

3.2 Formatting........................................................................................................ 9

3.3 About Data Backup.......................................................................................... 9

3.4 Contacting Technical Support......................................................................... 9

TABLE OF CONTENTS

03INTRODUCTION

1.1 SYSTEM REQUIREMENTS

Operating System:

- Mac and PC OS requirements differ based on enclosure type (see below)

Hardware:

- Mac or PC with an enclosure supporting a 3.5-inch drive form-factor using an NVMe U.2 connection.

Supported OWC enclosures include:

- OWC ThunderBay Flex 8 (top 4 bays only, top-left recommended)

- OWC Mercury Helios 3S with U.2 NVMe Interchange System

- OWC Mercury Pro U.2 Dual

Supported Drives Types:

- (4) NVMe M.2 drives with 2280 form factor and M-key connector

1.2 PACKAGE CONTENTS

INTRODUCTION

OWC U2 Shuttle Security keys Quick start guide

1.3 ABOUT THIS MANUAL

The images and descriptions may vary slightly between this manual and the unit shipped. Functions and features may

change depending on the rmware version. The latest product details and warranty information can be found on the

product web page. OWC’s Limited Warranty is not transferable and subject to limitations.

04DEVICE SETUP

DEVICE SETUP

2.1 INSTALLATION OF M.2 DRIVE(S)

This section describes the process of installing one or more

M.2 drives into the OWC U2 Shuttle. NVMe drives with a 2280

form factor and M-key connector are required. Other M.2 drive

types are not supported.

1. Remove the device from the retail packaging and set

it on a static-free work surface.

2. Remove the four cover screws at the locations shown

(there are two on each side).

3. Lift the cover off the device and set it aside.

4. Based on the number of M.2 drives you wish to install,

remove the screws from the corresponding drive posts

(highlighted), then set them aside.

5. For each SSD, align the M-key connector on the drive with

a connector on the PCBA and carefully seat the drive

in the connector. Minimal force is required. If a drive does

not seat correctly, do not apply more force. Remove the

drive, re-align it, and try again. Note: once seated

it is normal for each drive to sit at an angle.

6. For each SSD, hold the end of the M.2 drive down against

the corresponding drive post, then re-affix the screw you

removed earlier, to secure the drive in place.

7. Re-seat the cover, making sure that it sits flush with

the shuttle chassis on all sides. While maintaining a

modest amount of downward pressure on the cover,

re-affix the four screws you removed in Step 2 to secure

it. IMPORTANT: when the cover is seated and affixed

correctly, the tops of the “fins” on the cover will sit flush

with the top edges of the chassis. This reduces the

potential for installation issues when working with the

U.2 NVMe Interchange System.

This completes the drive installation process.

- To install with Mercury Helios 3S and U.2 NVMe

Interchange System, go to Section 2.2.

- To install in a ThunderBay Flex 8, skip to Section 2.3.

- To install in Mercury Pro U.2 Dual, skip to Section 2.4

05DEVICE SETUP

2.2 HOST INSTALLATION: HELIOS 3S WITH U.2 NVME

INTERCHANGE SYSTEM

This section describes the process of installing the OWC U2

Shuttle into the U.2 NVMe Interchange System. If you are

using both devices for the first time, you need to set up the

Helios 3S with the interchange system first. Please see the

assembly manual at www.owc.com/support/manuals for

instructions, then return to this page to install the Shuttle.

1. Note the shape of the cutout on the back of the U.2 NVMe

Interchange System; when installing the U2 Shuttle, you

need to first rotate it so that the side with the U.2 connector

is facing up. Make sure the connector is oriented to the left,

far edge.

2. Carefully slide the shuttle into the U.2 Interchange chassis.

When the shuttle contacts the U.2 connector inside the

device, a modest amount of force is required to fully

connect them. If the shuttle does not seat, do not apply

more force. Slide it back a small amount and then try again.

When seated it should “snap” into place.

IMPORTANT: when the cover is seated and affixed

correctly, the tops of the “fins” on the cover will sit flush

with the top edges of the chassis. If this is not the case,

you may have difficulty completing this step and potentially

cause cosmetic damage to the fins on the Shuttle. If the

fins are not completely flush please re-visit Section 2.2,

Step 7. You may need to remove and then reseat and re-

affix the cover, as described.

3. If you would like to lock the U2 Shuttle into place, insert

the included key into the lock and turn it until the lock

is secured, then remove the key.

Note: even though you are not using a PCIe card, this

Helios 3S configuration is not hot-swappable. Each time

you perform this installation you should power the Helios

3S off and disconnect it from power and the host computer,

install the U2 Shuttle, then reconnect the Helios 3S.

You can now mount the Helios 3S to your host computer,

format and/or RAID the M.2 drives installed using SoftRAID

or the RAID Assistant feature in Apple’s Disk Utility

application, and then begin using the drives.

06DEVICE SETUP

2.3 HOST INSTALLATION: THUNDERBAY FLEX 8

This section describes the process of installing the OWC U2

Shuttle into the ThunderBay Flex 8. If you are using both

devices for the first time, please familiarize yourself with the

ThunderBay and its drive sleds first. Please see the assembly

manual at www.owc.com/support/manuals for instructions,

then return to this page to install the Shuttle.

1. While it’s possible to install a U.2 drive or the U2 Shuttle

in any of the top four bays, we strongly recommend the

top-left bay to get the best performance. This bay offers

four lanes of PCIe bandwidth (x4) while the other three only

offer a single lane each (x1).

2. Seat the U2 Shuttle into the drive sled, making sure the

connector on the bottom of the shuttle is aligned with the

connector cutout at the front edge of the sled.

3. Also make sure the six screw holes on the shuttle (3 aside)

align with the corresponding holes on the sides of the drive

sled, then affix the shuttle using six of the 3.5 inch drive

screws that shipped with the ThunderBay.

4. Align the drive sled with the corresponding track inside the

chassis, then carefully insert the sled and slide it back until

the connector on the shuttle seats with the connector on

the ThunderBay; this is similar to the drive install process

described in Section 2.1, Step 8 in the ThunderBay manual.

If it does not seat initially, do not apply more force, remove

the tray, re-align it and try again.

Once the OWC U2 Shuttle is installed, you can format

and/or RAID the M.2 drives installed using SoftRAID

or the RAID Assistant feature in Apple’s Disk Utility

application, and then begin using the drives.

3 4

07DEVICE SETUP

2.4 HOST INSTALLATION: MERCURY PRO U.2 DUAL

This section describes the process of installing the OWC U2

Shuttle in the Mercury Pro U.2 Dual. The instructions listed

here will the same or very similar to the ones found in that

product’s assembly manual, located at

www.owc.com/support/manuals.

1. Remove Mercury Pro U.2 Dual from its packaging and set

it on a static-free work surface.

2. Remove the two screws highlighted in red from the back

of the enclosure and set them aside.

3. Pull on the front plate of the enclosure so the inner-chassis

slides out (A), then remove it fully (B).

4. Set the inner chassis flat on the work surface.

5. Making sure the connector on the shuttle aligns with

the connector on the inner-chassis, place the shuttle into

the housing. Then, connect the inner-chassis to the U2

Shuttle by sliding it in the direction shown until it is fully

seated. If the device does not seat fully, do not apply more

force. Move it back and try again. As long as the OWC U2

Shuttle is sitting flush in the drive carrier, the connectors

should automatically align.

6. Affix the U2 Shuttle to the inner-chassis at the locations

shown. Note: the hole for a 2.5 inch U.2 drive is circled in

yellow. A total of one screw is required for 2.5 inch drives,

and four screws (two per side) for 3.5 inch drives and the

OWC U2 Shuttle.

7. Once the U2 Shuttle is secured, flip the inner chassis

if needed and repeat Steps 5 and 6 to install another U.2

device or OWC U2 Shuttle.

3a 3b

08DEVICE SETUP

8. Make sure the ports on the back of the inner chassis and

the port cut-outs on the back of the outer enclosure are

oriented the same way, then slide the inner chassis into the

outer enclosure so that the chassis’ front plate is flush with

the cover’s front edge.

9. Re-affix the screws you removed in Step 2.

This completes the assembly process.

Once you’ve completed the installation steps, you can

format and/or RAID the M.2 drives using SoftRAID or the

RAID Assistant feature in Apple’s Disk Utility application,

and then begin using the drives. You can also format and

use the individual M.2 drives as independent volumes,

or a mix of independent and RAID volumes.

2.5 USAGE NOTES

- When using this device with a ThunderBay Flex 8, the top-left drive bay is recommended because it

provides the greatest PCIe bandwidth, to be shared among the drives installed in the Shuttle. The other 3

bays in the top row will function, but at potentially much slower speeds, unless you’re using a single M.2

drive in the shuttle.

09SUPPORT RESOURCES

3.1 TROUBLESHOOTING

Most problems with the U2 Shuttle can be traced back to one or more improperly installed M.2 drives and/

or a shuttle that is not fully connected to the host enclosure in which it is being used. Please disconnect

any host enclosure from power, remove the U2 Shuttle, then remove the cover and inspect the M.2 drive

connections. If they’re OK, re-seat and ax the cover, then re-seat the U2 Shuttle itself into the bay or drive

sled you’re using and try again. If you are still unable to see the M.2 drives in your system afterward, please

contact Technical Support.

3.2 FORMATTING

For additional formatting information, including instructions on how to format your M.2 SSDs for Mac

or Windows, go to: www.owc.com/support/formatting

3.3 ABOUT DATA BACKUP

To ensure that your les are protected and to prevent data loss, we strongly suggest that you keep two

copies of your data: one copy on your OWC U2 Shuttle and a second copy on your internal drive or another

storage medium, such as an optical backup, or on a second external storage unit. Any data loss or

corruption while using the U2 Shuttle is the sole responsibility of the user, and under no circumstances may

OWC, its parent, partners, aliates, ocers, employees, or agents be held liable for loss of the use of data

including compensation of any kind or recovery of the data.

3.4 CONTACTING TECHNICAL SUPPORT

SUPPORT RESOURCES

Phone: M–F: 8am–6pm CT, Sat & Sun: Closed

1.866.692.7100 (N. America) | +1.815.338.4751 (Int’l)

Chat: Sun: 9am–midnight, M–Th: 12am–4am & 7am–midnight (closed from 4am–7am),

Fri: 12am–4am & 7am–10pm (closed from 4am–7am), Sat: 9am–5pm

www.owc.com/support

Email: Answered within 48 hours

www.owc.com/support

CHANGES:

The material in this document is for information purposes only and subject to change without notice.

While reasonable efforts have been made in the preparation of this document to assure its accuracy, OWC,

its parent, partners, aliates, ocers, employees, and agents assume no liability resulting from errors or

omissions in this document, or from the use of the information contained herein. OWC reserves the right

to make changes or revisions in the product design or the product manual without reservation and without

obligation to notify any person of such revisions and changes.

FCC STATEMENT:

Warning! Modications not authorized by the manufacturer may void the user’s authority to operate this

device. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference with radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

WARRANTY:

The U2 Shuttle has a 1 Year OWC Limited Warranty without drives pre-installed and a 3 Year OWC Limited

Warranty on solutions with drive pre-installed. For up-to-date product and warranty information, please visit

the product web page.

COPYRIGHTS AND TRADEMARKS:

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by

any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written consent

of OWC.

of New Concepts Development Corporation, registered in the U.S. and/or other countries. Mac and macOS

are trademarks of Apple Inc., registered in the U.S. and other countries. Other marks may be the trademark

or registered trademark property of their owners.

OWCMANU2SHTL – 12.29.2020

Table des matières

Autres manuels OWC Stockage

OWC

OWC Mercury Express Manuel utilisateur

OWC

OWC Mercury Pro Manuel utilisateur

OWC

OWC ThunderBay 4 Mode d’emploi

OWC

OWC FLEX 1U4 Manuel utilisateur

OWC

OWC MERCURY ELITE PRO QUAD Mode d’emploi

OWC

OWC Mercury Elite Pro Dual Manuel utilisateur

OWC

OWC Envoy Pro Manuel utilisateur

OWC

OWC Mercury On-The-Go Pro Mode d’emploi

OWC

OWC Mercury Elite Pro Dual mini Mode d’emploi

OWC

OWC ACCELSIOR 1M2 Mode d’emploi

OWC

OWC Mercury Elite Pro Dual mini Mode d’emploi

OWC

OWC Mercury Elite-AL Manuel utilisateur

OWC

OWC RACK PRO MINI-SAS Mode d’emploi

OWC

OWC Mercury On-The-Go Pro Manuel utilisateur

OWC

OWC Envoy Pro Manuel utilisateur

OWC

OWC Mercury Helios Mode d’emploi

OWC

OWC Mercury Elite Pro Dual Manuel utilisateur

OWC

OWC ThunderBay 4 mini Mode d’emploi

OWC

OWC Mercury Pro LTO Mode d’emploi

OWC

OWC ThunderBay Flex 8 Mode d’emploi

OWC

OWC Mercury Elite Pro Qx2 Mode d’emploi

OWC

OWC Mercury Elite Pro Dual Manuel utilisateur

OWC

OWC Mercury Elite Pro Dual USB-C Mode d’emploi

OWC

OWC ThunderBay 4 mini Mode d’emploi

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur