OWC Mercury On-The-Go Pro Mode d’emploi

MERCURY

ON-THE-GO PRO

Assembly Manual & User Guide

OWC MERCURY ON-THE-GO PRO TABLE OF CONTENTS

CONTENTS

INTRODUCTION

1.1 Minimum System Requirements ................................................................1

1.1.1 Apple Mac Requirements

1.1.2 PC Requirements

1.1.3 Supported Drives

1.2 Package Contents......................................................................................1

1.3 About This Manual .....................................................................................1

1.4 LED Indicator .............................................................................................3

1.5 Rear View ..................................................................................................3

1.5.1 Rear Features.....................................................................................................3

DEVICE SETUP

2.1 Quick Start .................................................................................................4

2.2 Assembly....................................................................................................4

2.3 Usage Notes ..............................................................................................7

SUPPORT RESOURCES

3.1 Formatting..................................................................................................8

3.2 Unmounting Drives.....................................................................................8

3.3 Troubleshooting..........................................................................................8

3.4 About Data Backup....................................................................................8

3.5 Online Resources.......................................................................................8

3.6 Contacting Technical Support....................................................................9

OWC MERCURY ON-THE-GO PRO INTRODUCTION

1.1 Minimum System Requirements

1.1.1 Apple Mac Requirements

• USB 3.1 Gen 1 (compatible with USB 2.0): OS X 10.6 or later

• FireWire®800: OS X 10.2 or later

1.1.2 PC Requirements

• USB 3.1 Gen 1 (compatible with USB 2.0): Windows XP or later

• FireWire 800: Windows XP or later

1.1.3 Supported Drives

• Any 2.5 inch SATA drive

1.2 Package Contents

* On-The-Go Pro with SSD pictured; not all versions include an SSD.

**FireWire 800 cable included only with units that have FireWire 800 ports.

*** Screws and rubber feet included only with the “add your own drive” kits.

Phillips PH2 driver required.

1.3 About This Manual

The images and descriptions may vary slightly between this manual and the unit shipped. Functions and features

may change depending on the rmware version. Please visit the product web page for the current product

specications.

Mercury

On-The-Go Pro

USB 3.1 Gen 1 cable

(Standard-A to Micro-B)

FireWire 800 (1394b)

9-9 pin cable**

Carrying case

Screws and rubber feet ***

INTRODUCTION

OWC MERCURY ON-THE-GO PRO INTRODUCTION

To avoid damage, do not expose the device to temperatures outside: 41º — 107º F

(operating) or -40º — 149º F (non-operating)

Always unplug the device from the electrical outlet if there is a risk of lightning or if it will be

unused for an extended period of time. Otherwise, there is an increased risk of electrical

shock, short-circuiting or re.

Do not use the device near other electrical appliances such as televisions, radios or

speakers. Doing so may cause interference which will adversely aect the operation of the

other products.

Do not place the device near sources of magnetic interference, such as computer displays,

televisions or speakers. Magnetic interference can aect the operation and stability of hard

drives.

Do not place heavy objects on top of the device.

Protect your device from excessive exposure to dust during use or storage. Dust can build

up inside the device, increasing the risk of damage or malfunction.

Do not block any ventilation openings on the device. These help to keep the device cool

during operation. Blocking the ventilation openings may cause damage to the device and

cause an increased risk of short-circuiting or re.

Use proper anti-static precautions while installing your hard drives into this drive enclosure.

Failure to do so can cause damage to your drive mechanisms and/or the enclosure.

Read this user guide carefully and follow the recommended steps for assembly.

Do not attempt to disassemble or modify the device. To avoid any risk of electrical shock,

re, short-circuiting or dangerous emissions, never insert any metallic object into the device.

If it appears to be malfunctioning, please contact technical support.

Never expose your device to rain, or use it near water or in damp or wet conditions. Never

place objects containing liquids on the drive, as they may spill into its openings. Doing so

increases the risk of electrical shock, short-circuiting, re or personal injury.

General Use Precautions

Safety Precautions

OWC MERCURY ON-THE-GO PRO INTRODUCTION

1.4 LED Indicator

The Mercury On-The-Go Pro has a blue LED at the front. The LED emits a solid blue light when the unit is powered

on and ashes during drive activity.

1.5 Rear View

1.5.1 Rear Features

1. USB 3.1 Gen 1 port — Attach the included USB 3.1 Gen 1 (Standard-A to Micro-B) cable here.

2. On/O switch — Power the Mercury On-The-Go Pro on and o here.

3. Power input — Connect the optional 5V power adapter here (sold separately).

4. FireWire 800 ports — Attach the included 9-9 pin FireWire 800 cable to one of these ports and to the computer.

Use the other FireWire 800 port to daisy-chain other FireWire 800 devices. NOTE: Any device daisy-chained to the

Mercury On-The-Go Pro must be powered by its own power supply. The Mercury On-The-Go Pro cannot bus power

other devices.

1 2

1 2 3

OWC MERCURY ON-THE-GO PRO DEVICE SETUP

2.1 Quick Start

NOTE: If you are installing your own 2.5 inch SATA drive, skip this section and proceed to Section 2.2 for assembly

instructions.

You will need to format the Mercury On-The-Go Pro before using it. The OWC Drive Guide formatting utility has

been pre-installed to assist you. Follow the steps below to use Drive Guide to format the Mercury On-The-Go

Pro for Mac (OS X 10.4 and later) or Windows (XP and later). Connect the drive to the computer using the proper

cable. If you prefer to use a dierent formatting utility, do so at this time, then skip ahead to Section 3.1 to review

additional support information.

1. The drive will show up as “OWC SETUP”. Open the drive to view its contents.

2. Double-click the OWC Drive Guide application.

3. Follow the on-screen instructions to complete the formatting process.

4. Once the formatting is nished the drive is ready to use.

2.2 Assembly Steps

1. Remove the small piece of protective foam from

the open end of the enclosure. Tilt the enclosure

slightly so that the blue circuit board slides out

enough that you can remove it from the enclosure.

2. Insert the SATA connector on the back of the drive

into the SATA connector on the circuit board. Verify

the drive is fully seated before continuing.

DEVICE SETUP

OWC MERCURY ON-THE-GO PRO DEVICE SETUP

3. Holding the SATA drive in place, turn the circuit

board over. Using a Phillips driver and four of the

larger screws from the included packet, ax the

drive to the circuit board, as shown at right.

4. Align the front edge of the circuit board (i.e. the edge opposite the power switch) with the two grooves on the

heat sink (below left). Once aligned, carefully slide the entire circuit board into the enclosure, until the board

contacts the front cover (below right).

5. Take the plastic end-cap and align its cutouts with the ports on the circuit board (below left); make sure the

end-cap is not upside down. Next insert the end-cap into the back of the enclosure. The cutouts in the end-

cap should sit ush around the data port(s) and the power switch should protrude through the corresponding

cutout (below right).

OWC MERCURY ON-THE-GO PRO DEVICE SETUP

6. There is a small screw hole on each side of the

enclosure near the end-cap. Insert one of the two

smaller screws into each hole, then fasten them

to the enclosure.

7. Ax two more of the large screws from the

included packet into the two empty screw holes

that run through the plastic casing and heat sink.

NOTE: you will be left with a few spare screws;

store these in case you need them later.

8. Find the adhesive strip with the four rubber pads

attached to it. Each pad can be peeled o and

attached to one of the four similarly shaped

recesses on the bottom of the enclosure (shown

below). The assembly process is now complete.

OWC MERCURY ON-THE-GO PRO DEVICE SETUP

2.3 Usage Notes

• Connect only one interface (USB or FireWire) at a time.

• The Mercury On-The-Go Pro is designed to receive power through the USB or FireWire cable, therefore a separate

power adapter is not necessary and not included. For rare circumstances in which external power may be necessary,

an optional 5V power adapter is available: www.owcdigital.com/otg-power

• Some SSDs require the 5V power adapter to function properly when installed in the Mercury On-the-Go. Please see

Section 3.5 to contact technical support for more information.

• If the Mercury On-The-Go Pro is daisy-chained o of another FireWire device instead of being connected directly

to a computer, you must use the optional 5V power adapter. Attempting to bus-power the Mercury On-The-Go Pro

using the FireWire port of another device could cause damage to one or both devices, and should not be attempted.

• Even when the optional power adapter is not connected, the On/O switch must be in the ‘On’ position to use the

Mercury On-The-Go Pro.

• For the safe removal of the drive and to ensure that no data is lost, always eject or unmount the drive from the

operating system before powering o. See Section 3.2 for tips on the best ways to unmount the drive.

OWC MERCURY ON-THE-GO PRO SUPPORT RESOURCES

3.1 Fo r mat t in g

For additional drive formatting options and information, go to: www.owcdigital.com/format

3.2 Unmounting drives

To properly unmount any connected drives from the computer, please see the steps below.

OS X:

There are multiple options, including:

1) Drag the icon for the disk to the trash can;

2) Right-click the disk icon on the Desktop, then click “Eject”.

3) Highlight the disk icon on the Desktop, then press Command-E.

Windows:

Go to the System Tray (located in the lower right corner of the screen). Click the “Eject” icon (a small green arrow over

a hardware image). A message will appear, detailing the devices that the “Eject” icon controls, i.e., “Safely remove...”

Click on this prompt. You will then see a message that says, “Safe to Remove Hardware.” It is now safe to disconnect

the Mercury On-The-Go Pro from the computer.

3.3 Troubleshooting

Begin the troubleshooting by verifying that both ends of the cables are properly plugged into the computer and the

Mercury On-The-Go Pro. If the drive is still not working properly, try connecting to another interface such as the

USB port and see if the device works properly. You can also connect the On-The-Go Pro to a dierent computer.

If problems persist, see Section 3.5 to nd out about our online help resources, or see Section 3.6 for information

on contacting OWC technical support.

3.4 About Data Backup

To ensure that the les are protected and to prevent data loss, we strongly suggest that you keep two copies

of the data: one copy on the Mercury On-The-Go Pro and a second copy on either the internal drive or another

storage medium, such as an optical backup, or on another external storage unit. Any data loss or corruption while

using the Mercury On-The-Go Pro is the sole responsibility of the user, and under no circumstances may OWC,

its parents, partners, and aliates be held liable for loss of the use of data including compensation of any kind or

recovery of the data.

3.5 Online Resources

Data Migration

for our recommended method of migrating the data from an old drive to a new one, visit:

www.owcdigital.com/support/data-transfer

FAQs

Access our online collection of frequently asked questions for this and other products at:

www.owcdigital.com/support/faq

SUPPORT RESOURCES

Autres manuels pour Mercury On-The-Go Pro

Table des matières

Autres manuels OWC Stockage

OWC

OWC Mercury Elite-AL Pro Dual-Drive Manuel utilisateur

OWC

OWC Mercury Elite Pro Dual Manuel utilisateur

OWC

OWC MERCURY ELITE PRO MINI Manuel utilisateur

OWC

OWC Envoy Pro EX Manuel utilisateur

OWC

OWC ThunderBay 4 mini Mode d’emploi

OWC

OWC MERCURY PRO U.2 DUAL Mode d’emploi

OWC

OWC Mercury Elite Pro Qx2 Mode d’emploi

OWC

OWC RACK PRO MINI-SAS Mode d’emploi

OWC

OWC AURA Manuel utilisateur

OWC

OWC ThunderBay 8 Mode d’emploi

OWC

OWC mercury helios fx Manuel utilisateur

OWC

OWC OWC Elite Pro Manuel utilisateur

OWC

OWC ThunderBay 4 Mode d’emploi

OWC

OWC Mercury On-The-Go Pro Manuel utilisateur

OWC

OWC MERCURY ELITE PRO QUAD Mode d’emploi

OWC

OWC Mercury Elite Pro Dual Manuel utilisateur

OWC

OWC ThunderBlade V4 Manuel utilisateur

OWC

OWC ThunderBay 4 Mode d’emploi

OWC

OWC Mercury Elite FireWire 800 Pro Manuel utilisateur

OWC

OWC Mercury Elite Pro Dual Manuel utilisateur

OWC

OWC ThunderBay 4 mini Mode d’emploi

OWC

OWC Mercury Elite Pro Dual mini Mode d’emploi

OWC

OWC Envoy Manuel utilisateur

OWC

OWC Mercury Pro LTO Thunderbolt 3 Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur