Nokia NPC-1 Series Mode d’emploi

Programmes After Market Services

NPC-1 Series Transceivers

Issue 1 10/01 ãNokia Corporation

Troubleshooting Instructions

NPC-1

Troubleshooting Instructions PAMS Technical Documentation

Page 2 ãNokia Corporation Issue 1 10/01

Table of Contents Page No

Troubleshooting Instructions ..........................................................................................1

Transceiver Troubleshooting ......................................................................................... 4

Baseband Troubleshooting ..........................................................................................4

General about testing................................................................................................. 4

Troubleshooting ........................................................................................................ 5

Power up faults.......................................................................................................... 6

Flash Programming does not work.......................................................................... 10

Charging.................................................................................................................. 12

Audio failures.......................................................................................................... 13

Accessory detection................................................................................................. 15

Sleep Clock ............................................................................................................. 16

Display/Keyboard lights do not work ..................................................................... 18

Display does not work............................................................................................. 19

Buzzer does not work.............................................................................................. 20

Vibra does not work................................................................................................ 20

Keyboard does not work ......................................................................................... 20

Infrared does not work ............................................................................................ 21

Receiver Troubleshooting ..........................................................................................22

General instructions for RX troubleshooting.......................................................... 22

Path of the received signal ...................................................................................... 22

Fault finding charts for receiver chain .................................................................... 22

Transmitter Troubleshooting .....................................................................................26

General instructions for TX troubleshooting .......................................................... 26

Path of the transmitted signall................................................................................. 26

Fault finding charts for the transmitter.................................................................... 26

Synthesizer Troubleshooting .....................................................................................30

19.44 MHz reference oscillator............................................................................... 30

RX VHF VCO......................................................................................................... 31

TX VHF VCO......................................................................................................... 32

UHF SYNTHESIZER............................................................................................. 33

PAMS Technical Documentation Troubleshooting Instructions

NPC-1

Issue 1 10/01 ãNokia Corporation Page 3

List of Figures Page No

Fig 1 Power up sequence .....................................................................................................7

Fig 2 Fault tree, phone does not power up...........................................................................9

Fig 3 Fault tree, charging.....................................................................................................13

Fig 4 Fault tree, earpiece fail ...............................................................................................14

Fig 5 Fault tree, microphone fail .........................................................................................15

Fig 6 Fault tree, accessory detection....................................................................................16

Fig 7 Fault tree, sleep clock.................................................................................................17

Fig 8 Fault tree, Display/Keyboard lights............................................................................18

Fig 9 Fault tree, Display does not work...............................................................................19

Fig 10 Fault tree, infrared ....................................................................................................21

Fig 11 Fault tree. AMPS......................................................................................................23

Fig 12 Fault tree. Transmitter troubleshooting....................................................................27

Fig 13 Fault tree: Power control loop..................................................................................29

Fig 14 Detected voltages......................................................................................................30

Fig 15 Fault tree: 19.44 MHz oscillator...............................................................................31

Fig 16 Fault tree: RX VHF VCO.........................................................................................32

Fig 17 Fault tree: TX VHF VCO.........................................................................................33

Fig 18 Fault tree: UHF Synthesizer.....................................................................................34

NPC-1

Troubleshooting Instructions PAMS Technical Documentation

Page 4 ãNokia Corporation Issue 1 10/01

Transceiver Troubleshooting

The Troubleshooting instructions are divided into following sections:

1 How to check/fix the system/sleep clock.

2 How to check/fix the power supplies.

3 Contact service case.

4 How to check/fix the SIM faults.

5 How to check/fix the Audio faults.

6 How to check/fix the charger faults.

The first thing to do is to carry out a thorough visual check of the module. Make sure

that:

• there are no mechanical damages

• the solder joints are OK

Note: Before changing anything, ALL SUPPLY VOLTAGES AND THE SYSTEM

CLOCK / SLEEP CLOCK should be checked.

Baseband Troubleshooting

General about testing

The phone has three different modes for testing and/or repairing the phone. The modes

can be selected with suitable resistors connected to BSI- and BTEMP- lines as illustrated

in the table below:

If the corresponding resistors are connected, the MCU software automatically enters into

the local or test mode when the supply voltage is connected to the phone.

The power can be switched on by:

Table 1: Phone operating mode

Mode BSI-resistor BTEMP resistor Remarks

Normal 68k 47k

Local 560_ (<1k_) Whatever

Test > 1k 560_ (<1k_) Recommended for baseband test-

ing. Same as local mode, but mak-

ing a phone call is possible.

PAMS Technical Documentation Troubleshooting Instructions

NPC-1

Issue 1 10/01 ãNokia Corporation Page 5

1 Pressing the power key.

2 Connecting the local/test mode resistors to the bsi/btemp lines and connecting

the battery voltage to the phone.

3 Connecting a charger.

4 Phone’s internal functions (Real time clock alarm)

In the local and test mode, the baseband can be controlled through MBUS or FBUS (FBUS

is recommended) connections using Phoenix service software.

Troubleshooting

Note: Most of the baseband repair actions require removing the baseband shield.

The shield must not be removed unless authorized by PAMS.

Note: ESN has to re-written onto the phone, if the UEM is replaced. This can be

done only in Central Service.

The BB troubleshooting instructions consist of the following topics:

1Powerup

2 Flash programming

3Audio

• Earpiece

• Microphone

4 Charging

5 Accessory detection

6Sleepclock

7 User interface

•Display

• Lights

• Buzzer

•Vibra

• Keyboard

NPC-1

Troubleshooting Instructions PAMS Technical Documentation

Page 6 ãNokia Corporation Issue 1 10/01

8 Infrared

Power up faults

Power up sequence

1 The UEM acts as a HW master during start up

• Vbatt limits: 2.1V for internal state machine, 3V triggering whole startup

• Regulator sequencing

• HW "core" regulators "on": Vio, Vcore, VR3, Vflash1

• These regulators supply the processors, memory, chip interfaces and

clock source in RF

• Reset releasing delay

• Supply voltages stabilize to their UEM HW default values

• RFCLK grows to full swing

• The core is ready to run but waiting for the PURX release

• Reset releasing

• The UPP releases the SLEEPX up to the "non sleep" -state to prevent the

UEM switching the regulators "OFF"

2 MCU starts running the Bootsrap Code

• written in stone/ UPP internal ROM

• the program checks if there is any reason for the FDL mode (Flash Down

Load)

• If there is an executable code in FLASH and there is no reason for FDL,

the MCU starts running the MCU program from FLASH.

3 MCU runs the FLASH MCU code

• the phone initialization, user interfaces, internal blocks etc.

• Core regulator voltage setting for required DSP speed

• Initializes the DSP and concerning HW

• Releases DSP reset -> DSP starts running

PAMS Technical Documentation Troubleshooting Instructions

NPC-1

Issue 1 10/01 ãNokia Corporation Page 7

Note: In figure below, the RF_Clk frequency appears to be lower than 19.44MHz

because of a too low oscilloscope sampling frequency (2kS/s).

Figure 1: Power up sequence

1 Power key pressed

• After 20ms UEM enters RESET MODE if VBAT>Vmstr+

• VFLASH1, Vana, Vcore, Vio and VR3 goes high.

• VCTCXO enabled by VR3 -> RFClk 19.44 MHz running.

2 Purx released

• Purx released by UEM, UEMINT goes high for 100 ms, SleepX goes high and

UEM starts feeding SleepClk (32 KHz) to UPP.

Note: The sleepclock starts running in the crystal circuitry (B200) immediately when

the battery voltage is supplied.

3 Software running

NPC-1

Troubleshooting Instructions PAMS Technical Documentation

Page 8 ãNokia Corporation Issue 1 10/01

• Default value for Vcore is 1.5 volts and, if the software is running, Vcore will

rise to 1.8 volts.

• Cbus (1.08MHz) clock starts running.

Phonedoes not startup normallyor doesnot stayon

Note: In case of power up faults, it is not possible to force the phone on by disabling

the watchdog. Instead, measurements should be taken immediately when the power

key is pressed or when the battery voltage is connected to the phone (local/test

mode).

The easiest way to check if the software is running when the phone takes an abnormal

amount of current is to measure the cbusclk and Vcore.

The Dbus clock (programmable 9.72MHz) is not automatically visible in the test and local

modes.

PAMS Technical Documentation Troubleshooting Instructions

NPC-1

Issue 1 10/01 ãNokia Corporation Page 9

Figure 2: Fault tree, phone does not power up

Try to start phone to

test or local mode Check the

power key

Check X101

Measure

Vflash1,Vana,Vio,Vcore

,VR3when pwr key

pressed

Check 19.44MHz

RF-clock from C420

Check that purx

goes up to 1.8V

Change UPP

(D400)

Change the

UEM (D200)

Measure VBAT

from C261

Check R202,

R205, C217,

C220

Check G790

(missing,

misaligned)

Measure

J406. Should

be 1.08 MHz

Check

C420

Check

19.44MHz from

G790

Change N801

FAIL

Re-flash phone

FAIL

VANA & VR3

missing

FAIL

Check

R792,C792,

C793

Change

G790

FAIL

Programmng ok,

but phone doesn't

start Go to flash failure

chart

Programming

fails

NPC-1

Troubleshooting Instructions PAMS Technical Documentation

Page 10 ãNokia Corporation Issue 1 10/01

Flash Programming does not work

Flashprogrammingprocedure

1 The phone communicates with the prommer via the production test pattern,

using the following signals:

• FBUSTX(serial data to phone)

• FBUSRX(serial data from phone)

• MBUS(serial clock for FBUSRX)

• VPP(External flashing voltage for speed up flashing)

• The BSI line is also used when initializing flashing (battery connector).

2 When the phone is powered (VBAT>3V), the MBUS and FBUSTX lines are pulled

up internally by the phone.

3 The prommer sends a command to the UEM, using FBUSRX, to enter the Flash-

mode. During the sending of this command, the prommer keeps the BSI line high

and MBUS is used as a serial clock.

4 When the Flash-mode command is acknowledged, UEM enters the Flash-mode

and releases reset (PURX) to MCU.

5 After reset is released, UPP checks if there is a request for the Bootstrap code

(that resides in the UPP ROM).

6 The request for Bootstrap is the MBUS pulled down by the prommer (if the boot-

strap is not requested, the bootstrap code jumps to FLASH SW).

7 If the Bootstrap code is requested, UPP enters the Flash-mode and sets FbusTX to

'0' as an acknowledgement to the prommer. This is an indication that UPP can

run, at least, the fixed Bootstrap code – although it is not able to run the FLASH

code. UPP then sends an UPP-ID to the prommer via the FBUSTX line.

8 After the prommer has received the UPP-ID, it sends a corresponding Secondary

Boot Code to the phone via FBUSRX. The Secondary Boot Code, when run in UPP,

requests UPP to send information to the prommer about the flash type and other

HW-related parameters about the device to be flashed.

9 Prommer then sends the Algorithm Code corresponding to the HW parameters,

and this algorithm, when run in UPP, takes over handling the MCUSW transfer to

Flash.

10 12 volts can be supplied to Vpp (by the prommer) to speedup flashing.

Table des matières

Autres manuels Nokia Émetteur-récepteur

Nokia

Nokia NSM-5 SERIES Mode d’emploi

Nokia

Nokia RH-34 Series Guide de démarrage rapide

Nokia

Nokia NSC-1 SERIES Manuel utilisateur

Nokia

Nokia NSM-5 SERIES Instructions d'installation

Nokia

Nokia NSB-1 Series Manuel utilisateur

Nokia

Nokia NSB-6 Series Instructions d'installation

Nokia

Nokia RH-21 Series Mode d’emploi

Nokia

Nokia RH-41 Series Instructions d'installation

Nokia

Nokia RH-27 Series Mode d'emploi

Nokia

Nokia NSC/W-1/3 Series Instructions d'installation

Nokia

Nokia RH-10 Series Mode d'emploi

Nokia

Nokia RM-11 Series Mode d'emploi

Nokia

Nokia NPM-6 Series Manuel utilisateur

Nokia

Nokia NHM-8NX Series Mode d’emploi

Nokia

Nokia NSE-6 SERIES Manuel utilisateur

Nokia

Nokia NSM-3 Mode d’emploi

Nokia

Nokia NSB-5 Series Instructions d'installation

Nokia

Nokia RH-57 Series Mode d'emploi

Nokia

Nokia NPM–9 Series Instructions d'installation

Nokia

Nokia RH-21 Series Guide de démarrage rapide

Nokia

Nokia RM-696 Manuel utilisateur

Nokia

Nokia NME-3 Series Manuel utilisateur

Nokia

Nokia NSW-1 Series Manuel utilisateur

Nokia

Nokia RH-27 Series Mode d’emploi

Manuels Émetteur-récepteur populaires d'autres marques

Yaesu

Yaesu FT-7B Manuel utilisateur

Kenwood

Kenwood ProTalk TK-3201 Manuel utilisateur

Texas Instruments

Texas Instruments TLK10232 Manuel utilisateur

Mizuho

Mizuho MX-2 Guide produit

Kenwood

Kenwood TK-3180 Manuel d'utilisation et d'entretien

Blitz

Blitz MJ-398U Manuel utilisateur

Utilicom

Utilicom LongRanger 2050 Manuel utilisateur

Standart

Standart HX290UKA Manuel utilisateur

Altronix

Altronix Pace1PTM Manuel utilisateur

Kirisun

Kirisun PT2208 Manuel utilisateur

ELECRAFT

ELECRAFT KX2 Manuel utilisateur

Zodiac

Zodiac K3 Manuel utilisateur

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuel utilisateur

Kenwood

Kenwood TK-2217 Manuel utilisateur

Siemens

Siemens PSO 4000 Manuel utilisateur

Kenwood

Kenwood TS-590SG Manuel utilisateur

Midland

Midland G8E-BT Manuel

ComNav

ComNav Mariner X2 Manuel utilisateur