Nokia RH-41 Series Manuel utilisateur

CCS Technical Documentation

RH-41 Series Transceivers

Issue 2 09/2003 Confidential Nokia Corporation

Assembly

RH-41

Assembly CCS Technical Documentation

Page 2 Nokia Corporation Confidential Issue 2 09/2003

CCS Technical Documentation Assembly

RH-41

Issue 2 09/2003 Nokia Corporation Confidential Page 3

Assembling the RH-41 Basic Transceiver

Assemble the D-cover assembly.

Step 1. Assemble the metal deck from the

back cover side by pressing it with your

fingers.

All six tabs should snap into the slots in the

D-cover.

Step 2. Place the IR window onto the

D-cover before assembling the

antenna.

Step 4. Press the antenna into its place.

Note: Make sure that the antenna springs do not

get damaged or touched during assembly.

No fingerprints should get on the springs.

4. Step 5. Place one end of the battery latch into

the D-cover slot.

Step 6. Bend the latch and move the other

end into the D-cover slot.

The battery connector will be assembled onto the D-cover

with interference fixing.

Step 7. Place connector onto D-cover with tweezers.

Step 8. Push the connector into the D-cover slot with your fingers.

Note: Make sure that the

battery connector is

below the D-cover edges after assembly. If the

buzzer or vibra assembly is in place, make

sure that the buzzer springs stay intact. They

may be damaged, if touched.

RH-41

Assembly CCS Technical Documentation

Page 4 Nokia Corporation Confidential Issue 2 09/2003

Step 9. Place the vibra assembly into its slot. Use

tweezers.

The vibra is assembled into the D-cover with

interference fixing.

Note: If the battery connector or the buzzer assembly is in

place, make sure that the battery connector springs

and the buzzer springs stay intact. The springs may be

damaged, if touched.

Step 10. Place the buzzer assembly into its place.

Use tweezers.

The buzzer is assembled into the D-cover with

interference fixing.

8. Step 11. Place the release spring into the

D-cover slot.

The release spring is attached onto the

D-cover with screws that are used for

attaching the C- and D-covers. No heat

staking is needed.

Assemble the C-cover.

Step 1. Check the condition of the screw holes

If they are worn out, change the cover.

Step 2. Place the C-cover into a jig. Make sure

that the speaker with the speaker

gasket is in place.

Note: Make sure that the speaker springs stay intact. They may be damaged, if touched.

10. Note: the use of gloves or a vacuum picker

is required, in order to prevent

fingerprints from appearing on the

LCD. Make sure that the elastomer

connector and domes stay intact

during assembly. Use compressed air

or a vacuum before assembling

the D-cover, in order to prevent

dust from getting onto the engine

layout.

Place the LCD module onto the C-cover.

CCS Technical Documentation Assembly

RH-41

Issue 2 09/2003 Nokia Corporation Confidential Page 5

15.

11.

12.

13.

14.

Note: The use of gloves is mandatory in

order to prevent fingerprints from

appearing on the engine layout. Use

ionized air or a vacuum, before

assembling the D-cover, to remove

dust and other foreign particles

from the PWB assy.

Place the system connector on top of the

engine module.

Note: The use of gloves is mandatory in order to

prevent fingerprints from appearing on

the engine layout and system connector

pads (charging pads). Make sure that the

system connector springs stay intact. The

springs may be damaged, if touched.

Assemble the screws.

Step 1. Fasten the 6 screws. The assembly

order is shown in the disassembly

section. The torque is 20 - 21 Ncm

350/RPM.

16.

Assemble the keymat onto the front cover.

Step 1. Place the keypad onto the front

cover before the cover is assembled

to the basic transceiver.

Step 2. Press the keypad into its place.

Assemble the front cover onto the basic

transceiver.

Place the engine module on top of the

LCD module.

Step 2. Press the D-cover to snap the side locks.

C-cover.

Step 1. Place the assembled D-cover on top of the

Assemble the D-cover assembly.

Step 1. First push the basic transceiver to the

front cover’s IR window.

Step 2. Press the bottom part onto the front

part, so that it snaps onto the front

cover.

RH-41

Assembly CCS Technical Documentation

Page 6 Nokia Corporation Confidential Issue 2 09/2003

17.

18.

Assemble the battery.

Step 1. Push the battery connector interface.

Step 2. Press the battery down so that the

latch fits the battery in place.

Assemble the back cover.

Step 1. Place the back cover on the

phone.

Step 2. Slide the cover so that the spring snaps the

cover into place.

Autres manuels pour RH-41 Series

Autres manuels Nokia Émetteur-récepteur

Nokia

Nokia NME-2A Series Manuel utilisateur

Nokia

Nokia RM-11 Series Mode d'emploi

Nokia

Nokia NPD-4 Series Manuel utilisateur

Nokia

Nokia NHM-4 Series Manuel utilisateur

Nokia

Nokia NKC-1X Series Mode d’emploi

Nokia

Nokia NSC/W-1/3 Series Manuel utilisateur

Nokia

Nokia NSE-5 Series Instructions d'installation

Nokia

Nokia NSC-1 SERIES Guide de configuration

Nokia

Nokia NSB-6 Series Instructions d'installation

Nokia

Nokia NPM-6 Series Mode d’emploi

Nokia

Nokia NSB-5 Series Mode d’emploi

Nokia

Nokia NSW-6 Series Mode d’emploi

Nokia

Nokia NSE-6 SERIES Mode d’emploi

Nokia

Nokia NSE-6 SERIES Instructions d'installation

Nokia

Nokia NSC-1 SERIES Manuel utilisateur

Nokia

Nokia NPM–9 Series Instructions d'installation

Nokia

Nokia NSM-5 SERIES Mode d’emploi

Nokia

Nokia NSB-1 Series Mode d’emploi

Nokia

Nokia RH-41 Series Mode d’emploi

Nokia

Nokia NSM-3 Manuel utilisateur

Nokia

Nokia RH-20 Manuel utilisateur

Nokia

Nokia RH-34 Series Mode d’emploi

Nokia

Nokia NPM-6 Series Manuel utilisateur

Nokia

Nokia RH-27 Series Mode d’emploi

Manuels Émetteur-récepteur populaires d'autres marques

Yaesu

Yaesu FT-7B Manuel utilisateur

Kenwood

Kenwood ProTalk TK-3201 Manuel utilisateur

Texas Instruments

Texas Instruments TLK10232 Manuel utilisateur

Mizuho

Mizuho MX-2 Guide produit

Kenwood

Kenwood TK-3180 Manuel d'utilisation et d'entretien

Blitz

Blitz MJ-398U Manuel utilisateur

Utilicom

Utilicom LongRanger 2050 Manuel utilisateur

Standart

Standart HX290UKA Manuel utilisateur

Altronix

Altronix Pace1PTM Manuel utilisateur

Kirisun

Kirisun PT2208 Manuel utilisateur

ELECRAFT

ELECRAFT KX2 Manuel utilisateur

Zodiac

Zodiac K3 Manuel utilisateur

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuel utilisateur

Kenwood

Kenwood TK-2217 Manuel utilisateur

Siemens

Siemens PSO 4000 Manuel utilisateur

Kenwood

Kenwood TS-590SG Manuel utilisateur

Midland

Midland G8E-BT Manuel

ComNav

ComNav Mariner X2 Manuel utilisateur