ELECRAFT KX2 Manuel utilisateur

Elecraft • www.elecraft.com • 831-763-4211

Elecraft KX2

Harmonic Level Reduction

E740304

Revision B, June 7, 2017

Introduction

This modification reduces the level of harmonics present in the KX2 output for early KX2 transceivers. No

soldering is required. If you prefer, Elecraft can install the modification for you. E-mail k3support@elecraft.com

or call 863-763-4211.

Has my KX2 Been Modified?

You can check to see if the modification is installed by opening the case as if you were changing the battery (see

Figure 1 on page 2). Inspect the transistors mounted on the end panel near the antenna connector (see Figure 7 on

page 5). If the thermal insulator is present between the transistor heat sinks and the end panel, or if you can see a

copper strip connecting the two heat sinks (when no KXAT2 is installed) the modification has been done.

Parts Required

You can order a kit containing the required parts from Elecraft. Order KX2MDKTHS

IMAGE

QUANTITY

DESCRIPTION

ELECRAFT PART

NUMBER

1.25” (3.18 cm)

Copper Tape

Do not remove from backing until

instructed to do so.

E980339

0.4” (10.2 mm)

Foam Tape

Do not remove from backing until

instructed to do so.

E980338

Thermal Insulator

Both insulators may be supplied on

the same paper backing.

Do not remove from backing until

instructed to do so.

E700002

Shoulder Enhanced

in Image

Shoulder Washer

E700001

Nut, 4-40, 0.062” (1.6 mm) Thick

E700055

#4 Lock Washer, Internal Tooth

E700010

Tools Required

1. A No 1 Phillips-head screwdriver.

2. Thin nose (1/8” or 3 mm) pliers to hold nuts with limited clearance space (see Figure 7, page 5).

3. A small rule (see Figure 4, page 3).

4. A soft surface that you can lay the KX2 on without scratching the LCD cover or case.

5. A grounded wrist strap and ESD dissipating mat are recommended whenever you work inside your KX2.

Optionally, touch a bare metal ground frequently while working.

KX2 Harmonic Reduction Modification Instructions Page 2 Page 2 of 5

Procedure

Disconnect all cables and, if used, external power from your KX2.

With the KX2 face down, loosen the two thumb screws and carefully remove the bottom cover as shown in

Figure 1. Take care to avoid pulling on the cable leading to the speaker.

Figure 1. Opening the KX2.

A grounded wrist strap and ESD dissipating mat are recommended whenever you work on pc boards

inside your KX2. Optionally, touch a bare metal ground frequently while working.

Remove the screws from the end plate with the BNC connector as shown in Figure 2.

Figure 2. Removing the End Plate Screws.

KX2 Harmonic Reduction Modification Instructions Page 3 Page 3 of 5

Unplug the BNC connector to free the end plate as shown in Figure 3.

Figure 3. Unplugging the Antenna Connector.

Mount the thermal insulators and foam tape on the inside surface of the end panel as shown in Figure 4. Be

sure the thermal insulators are positioned as shown, with the holes directly over the screw holes in the end panel

and aligned square with the edges of the panel.

Figure 4. Mounting the Thermal Insulators and Foam Tape.

KX2 Harmonic Reduction Modification Instructions Page 4 Page 4 of 5

Remove the protective covering from the foam tape and from the copper tape. Carefully position the copper

tape as shown in Figure 5. When the end panel is replaced, the copper tape must contact both transistor heat sinks,

but not touch the end cover at any point.

Figure 5. Modified End Panel.

Replace the end panel with the three screws that thread into the bracket on the front panel. Do not reattach the

transistor heat sinks yet.

Use the new shoulder washers, 4-40 nuts and interior tooth lock washers to reattach the transistor heat sinks

as shown in Figure 6. This hardware replaces the nuts with captive washers you removed. They will not be used.

A magnetized screwdriver can help hold the lock washer on the screw while starting the nut, especially if the

KXAT2 ATU is installed.

Figure 6. New Transistor Mounting Hardware.

KX2 Harmonic Reduction Modification Instructions Page 5 Page 5 of 5

Be sure the hardware is tightened to ensure the transistor heat sinks are in firm contact with the thermal

insulators and the antenna connector is reattached to either the RF board if KXAT2 or to the KXAT2. The

completed installation is shown in Figure 7.

Figure 7. Completed Modification.

Replace the battery (if installed) and close the case (see Figure 1 on page 2).

That completes the modification.

Autres manuels pour KX2

Table des matières

Autres manuels ELECRAFT Émetteur-récepteur

ELECRAFT

ELECRAFT K3 Manuel utilisateur

ELECRAFT

ELECRAFT K3 Manuel du propriétaire

ELECRAFT

ELECRAFT K1 Manuel utilisateur

ELECRAFT

ELECRAFT K3 Manuel utilisateur

ELECRAFT

ELECRAFT K3 Manuel utilisateur

ELECRAFT

ELECRAFT K3S Manuel utilisateur

ELECRAFT

ELECRAFT KNB2 Manuel utilisateur

ELECRAFT

ELECRAFT K3 Manuel utilisateur

ELECRAFT

ELECRAFT KX3 Manuel utilisateur

ELECRAFT

ELECRAFT KX2 Manuel utilisateur

ELECRAFT

ELECRAFT K3 Manuel du propriétaire

ELECRAFT

ELECRAFT K3S Manuel utilisateur

ELECRAFT

ELECRAFT K2 Manuel utilisateur

ELECRAFT

ELECRAFT K3 Manuel utilisateur

ELECRAFT

ELECRAFT K3 Manuel utilisateur

ELECRAFT

ELECRAFT KXV3 Manuel utilisateur

ELECRAFT

ELECRAFT K3 Manuel utilisateur

ELECRAFT

ELECRAFT K4 Manuel de référence

ELECRAFT

ELECRAFT K3S Manuel utilisateur

ELECRAFT

ELECRAFT K3S KAT3A Manuel utilisateur

ELECRAFT

ELECRAFT K2 Manuel utilisateur

ELECRAFT

ELECRAFT KX3 Manuel utilisateur

ELECRAFT

ELECRAFT K3S Manuel utilisateur

ELECRAFT

ELECRAFT K3S Mode d’emploi

Manuels Émetteur-récepteur populaires d'autres marques

Yaesu

Yaesu FT-7B Manuel utilisateur

Kenwood

Kenwood ProTalk TK-3201 Manuel utilisateur

Texas Instruments

Texas Instruments TLK10232 Manuel utilisateur

Mizuho

Mizuho MX-2 Guide produit

Kenwood

Kenwood TK-3180 Manuel d'utilisation et d'entretien

Blitz

Blitz MJ-398U Manuel utilisateur

Utilicom

Utilicom LongRanger 2050 Manuel utilisateur

Standart

Standart HX290UKA Manuel utilisateur

Altronix

Altronix Pace1PTM Manuel utilisateur

Kirisun

Kirisun PT2208 Manuel utilisateur

Zodiac

Zodiac K3 Manuel utilisateur

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuel utilisateur

Kenwood

Kenwood TK-2217 Manuel utilisateur

Siemens

Siemens PSO 4000 Manuel utilisateur

Kenwood

Kenwood TS-590SG Manuel utilisateur

Midland

Midland G8E-BT Manuel

ComNav

ComNav Mariner X2 Manuel utilisateur

Uniden

Uniden UH820 Series Manuel utilisateur