Njoy Token Series Manuel utilisateur
Token Series User Manual
Manual de ulizare
UPCSBLS660TTOAZ01B
UPCSBLS680TTOAZ01B
Before using this product, carefully read all product documentaon and retain it for future reference.
149.34.22.1
2
UPS unit
Power cord (attached)
USB cable
User manual
Warranty card
Package contents
1
The following models belong to the Token Series UPS:
600 VA
800 VA
Token 600
Token 800
Thank you for purchasing our products!
Please read this manual before using the product.
nJoy is a brand of power and backup protecon products that
create soluons for mulple levels of environment complexity,
residenal to industrial
This UPS will protect your electronic equipment from physical
damage and will provide emergency baery backup power to
prevent data loss in the event of power problems.
NOTE!
Before installaon, please inspect the unit. Be sure that nothing inside the
package is damaged. Keep the original package in a safe place for future use.
4
1. LED indicators (for Token 600 model) / LCD display (for Token 800
model): Indicate status informaon, sengs and events.
2. Power On/O buon: To turn on the UPS unit, press the power
switch lightly. Then, the LED or LCD will light up. To turn o the UPS
unit, press the power switch again. Then, display will shut o.
POWER
SURGE ONLY BATTERYBACKUP
BATTERY
LOAD
INPUT
VAC
A
Hz
VAC
A
Hz
OUTPUT
Token 800
2
34
7
5
6
8
8
9
1
5
English
Română
Important safety warnings
3
Please comply with all warnings and operang instrucons in this manual
strictly. Save this manual properly and carefully read the following
instrucons before installing the unit. Do not operate this unit before
reading through all safety informaon and operang instrucons
carefully:
Transportaon
• Please transport the UPS system only in the original package to
protect against shock and impact.
Preparaon
• Condensaon may occur if the UPS system is moved directly from
cold to warm environment. The UPS system must be absolutely dry
before being installed. Please allow at least two hours for the UPS
system to acclimate to the environment.
• Do not install the UPS system near water or in moist environments.
3. Baery backup outlets: These outlets provide baery backup, EMI
ltering, line condioning, and surge protecon. Baery power is
automacally provided in case of power failure.
4. Surge-protected outlets: These outlets do not provide power during
power failure.
5. HID USB port: Allows the UPS to appear in Windows like a baery
icon. When the power is out, you can sll see the baery level and
adjust its sengs. Also Windows power management opons are
available. In case you need more advanced local management we
recommend you to install and use “ViewPower” soware.
6. Network, Modem or Phone surge protecon: (only for Token 800
model) This UPS protects a single line (1 in/1 out) phone, modem, or
fax machine from surges when connected through the UPS.
7. USB charger port: 5VDC, 2.1A (only for Token 800 model)
8. AC input power cord: Connect to ulity power.
9. Input circuit breaker: The circuit breaker provides opmal overload
protecon.
6
• Do not install the UPS system where it would be exposed to direct
sunlight or near heat sources.
• Do not block venlaon holes in the UPS housing.
Installaon
• Do not connect appliances or devices which would overload the UPS
system (e.g. laser printers) to the UPS output sockets.
• Place cables in such a way that no one can step on or trip over them.
• Do not connect domesc appliances such as hair dryers to UPS
output sockets.
• The UPS can be operated by any individuals with no previous
experience.
• Connect the UPS system only to an earthed shockproof outlet which
must be easily accessible and close to the UPS system.
• Please use only VDE-tested, CE-marked mains cable (e.g. the mains
cable of your computer) to connect the UPS system to the building
wiring outlet (shockproof outlet).
• Please use only VDE-tested, CE-marked power cables to connect the
loads to the UPS system.
• When installing the equipment, it should ensure that the sum of
the leakage current of the UPS and the connected devices does not
exceed 3.5mA.
Operaon
• Do not disconnect the mains cable on the UPS system or the building
wiring outlet (shockproof socket outlet) during operaons since this
would cancel the protecve earthing of the UPS system and of all
connected loads.
• The UPS system features its own, internal current source (baeries).
The UPS output sockets or output terminals block may be electrically
live even if the UPS system is not connected to the building wiring
outlet.
• In order to fully disconnect the UPS system, rst press the OFF/Enter
buon to disconnect the mains.
• Prevent uids or other foreign objects from entering the inside of the
UPS system.
7
English
Română
• WARNING: This is a category C2 UPS product. In a residenal
environment, this product may cause radio interference, in which
case the user may be required to take addional measures.
Maintenance, service and faults
• The UPS system operates with hazardous voltages. Repairs may be
carried out only by qualied maintenance personnel.
• Cauon - risk of electric shock. Even aer the unit is disconnected
from the mains (building wiring outlet), components inside the UPS
system are sll connected to the baery and electrically live and
dangerous.
• Before carrying out any kind of service and/or maintenance,
disconnect the baeries and verify that no current is present and no
hazardous voltage exists in the terminals of high capability capacitor
such as BUS-capacitors.
• Only persons are adequately familiar with baeries and with the
required precauonary measures may replace baeries and supervise
operaons. Unauthorized persons must be kept well away from the
baeries.
• Cauon - risk of electric shock. The baery circuit is not isolated
from the input voltage. Hazardous voltages may occur between the
baery terminals and the ground. Before touching, please verify that
no voltage is present!
• Baeries may cause electric shock and have a high short-circuit
current. Please take the precauonary measures specied in this
manual and any other measures necessary when working with
baeries: remove wristwatches, rings and other metal objects, use
only tools with insulated grips and handles.
• When changing baeries, install the same number and same type of
baeries.
• Do not aempt to dispose of baeries by burning them. This could
cause baery explosion.
• Do not open or destroy baeries. Escaping electrolyte can cause
injury to the skin and eyes. It may be toxic.
• Please replace the fuse only with the same type and amperage in
order to avoid re hazards.
• Do not dismantle the UPS system.
8
Installing your UPS system
4
4.1 Hardware installaon guide
1. Placement & Storage condions
Install the UPS in a protected area that is free of excessive dust and
has adequate air ow. Please place the UPS away from other units at
least 20 cm to avoid interference. Do NOT operate the UPS where the
temperature and humidity is outside the specic limits. (Please check the
specs for the limitaons.)
2. Connect to ulity and charging
Plug in the AC input cord to the wall outlet. For the best results, suggest
to charge the baery at least 6 hours before inial use. The unit charges
its baery while connecng to the ulity.
3. Connect the loads
Plug in the loads to output receptacles on the front panel of the UPS.
Simply turn on the power switch of UPS unit, then devices connected to
the UPS will be protected by UPS unit.
Due to its high-power consumption, we do NOT recommend
connecting LASER PRINTERS or loudspeaker equipment
such as SUBWOOFERS to this type of UPS.
Do NOT plug any SURGE STRIPS into any of the outlets.
CAUTION
4. Connect communicaon cable
To allow for unaended UPS shutdown/start up and status monitoring,
connect the communicaon cable one end to the USB port and the other
to the communicaon port of your PC. With the monitoring soware
installed, you can schedule UPS shutdown/start up and monitor UPS
status through PC.
9
English
Română
5. Connect Modem/Phone /Network for surge protecon
Connect a single modem/phone line into surge protected “IN” outlet
on the side panel of the UPS unit. Connect from “OUT” out let to the
computer with phone line cable.
6. Turn On/O the unit
Turn on the UPS unit by pressing the power switch. Turn o the UPS unit
by pressing again the power switch.
4.2 Soware installaon guide
Install soware: For opmal computer system protecon, install the UPS
monitoring soware from hps://www.power-soware-download.com/
viewpower.html to fully manage the UPS.
4.3 Posioning
• For opmal venlaon of the UPS, please place it 15cm distance
from any wall or object.
Indicators
5
5.1 LED indicators (for Token 600 model)
Red Yellow Green
10
UPS Mode LCD display Descripon
UPS Power
on
When UPS is powered
on, it will enter this
mode for few seconds.
Standby
Mode
In standby mode,
no output power is
available.
AC Mode
When AVR is funconing, icon
will ash every second.
When the input
voltage is within
acceptable range, UPS
will provide stable AC
power to output. The
UPS will also charge
the baeries in AC
mode.
5.2 LCD display indicators (for Token 800 model)
LED Alarm UPS Status
Green (LED on) O The mains is normal and
UPS is operated normally.
Yellow (LED ashing) Sounding every
10 seconds
Power failure occurs and
UPS is on baery mode.
Yellow (LED ashing) Sounding every
second Low baery
Green (LED o) O UPS is o.
Red (LED on) Connuously
sounding UPS fault
Autres manuels pour Token Series
1
Ce manuel convient aux modèles suivants
2
Table des matières
Langues :
Autres manuels Njoy UPS
Njoy
Njoy Balder Series Manuel utilisateur
Njoy
Njoy Aten PRO Series Manuel utilisateur
Njoy
Njoy Protector 801 Manuel utilisateur
Njoy
Njoy Echo Pro Series Manuel utilisateur
Njoy
Njoy Horus Plus Series Manuel utilisateur
Njoy
Njoy Helios PRO Series Manuel utilisateur
Njoy
Njoy PWAV-10001AK-AZ01B Manuel utilisateur
Njoy
Njoy Shed 625 Manuel utilisateur
Njoy
Njoy Soter 600 Manuel utilisateur
Njoy
Njoy UPCSBLS665TRPCG01B Manuel utilisateur
Njoy
Njoy Garun Series Manuel utilisateur
Njoy
Njoy Soter 600 Manuel utilisateur
Njoy
Njoy Echo Pro Series Manuel utilisateur
Njoy
Njoy Keen Series Manuel utilisateur
Njoy
Njoy Balder Series Manuel utilisateur
Njoy
Njoy Renton 650 Manuel utilisateur
Njoy
Njoy Horus Plus Series Manuel utilisateur
Njoy
Njoy Aster Series Manuel utilisateur
Njoy
Njoy Aster 6KT Manuel utilisateur
Njoy
Njoy PWUP-LI060H1-AZ01B Manuel utilisateur
Manuels UPS populaires d'autres marques
Pylontech
Pylontech Victron & Pylontech US5000 Manuel utilisateur
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur
Mecer
Mecer ME-1000-WTU Manuel utilisateur
Mustek
Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation
Emerson
Emerson Liebert NXL series Manuel utilisateur
MAKELSAN
MAKELSAN BOXER SERIES Manuel utilisateur
