NI DAQPad-6016 OEM Manuel utilisateur

USER GUIDE

NI DAQPad -6016 OEM

This document provides dimensions, connector pinouts, and information

about the LEDs, switches, chassis ground, and connectors of the following

NI DAQPad-6016 OEM devices:

•111 mm ×163 mm Version—For information about this version of

the DAQPad-6016 OEM device, refer tothe DAQPad-6016 OEM

(111 mm

163 mm Version) section of this document.

•191 mm ×163 mm Version—For information about this version of

the DAQPad-6016 OEM device, refer to the DAQPad-6016 OEM

(191 mm

163 mm Version) section of this document.

Caution There are no product safety, electromagnetic compatibility (EMC), or

CE marking compliance claims made for the NI DAQPad-6016 OEM devices. Conformity

to any and all compliance requirements rests with the end product supplier.

DAQPad-6016 OEM (111 mm ×163 mm Version)

Figure 1 shows the 111 mm ×163 mm version of the DAQPad-6016 OEM

device.

For specifications and more information about the DAQPad-6016 OEM

device, refer to the E Series Help at ni.com/manuals.

Figure 1. DAQPad-6016 OEM Device (111 mm ×163 mm Version)

™

NI DAQPad-6016 OEM User Guide 2 ni.com

Dimensions

Figure 2 shows the dimensions of the 111 mm ×163 mm version of the

DAQPad-6016 OEM device.

Figure 2. DAQPad-6016 OEM Dimensions in Inches and Millimeters

(111 mm ×163 mm Version)

4.354 (110.59)

0.000 (0.00)

0.150 (3.81)

0.390 (9.91)

0.550 (13.98)

3.180 (80.77)

3.220 (81.79)

3.280 (83.31)

1.057 (26.85)

0.390 (9.91)

0.000 (0.00)

2.145 (54.48)

2.606 (66.19)

3.080 (78.23)

6.200 (157.48)

–0.055 (–1.4)

0.515 (13.08)

0.362 (9.19)

0.162 (4.11)

–0.100 (–2.54)

–0.215 (–5.45)

6.010 (152.65)

4.070 (103.38)

3.730 (94.74)

3.614 (91.83)

3.524 (89.55)

0.436 (11.07)

0.392 (9.96)

0.000 (0.00)

4X φ0.125 (3.18)

0.304 (7.72)

0.200 (5.08)

5.850 (148.59)

6.400 (162.63)

0.000 (0.00)

–0.203 (–5.16)

Full 50-Pin

I/O Connector

Pin 1 Pin 49

Pin 2 Pin 50

Pin 1 Pin 49

Pin 2 Pin 50

Extended

DIO 50-Pin

I/O Connector

3.949 (100.30)

©National Instruments Corporation 3 NI DAQPad-6016 OEM User Guide

I/O Connector Pinouts

Table 1 shows the two 50-pin I/O connector pinouts on the DAQPad-6016

OEM device.

For more information about the DAQPad-6016 OEM signals and how to

connect them, refer to the E Series Help at ni.com/manuals.

Table 1. DAQPad-6016 OEM I/O Connector Pinouts

Full 50-Pin I/O Connector Extended DIO 50-Pin I/O Connector

CTR 0 OUT

PFI 8/CTR 0 SRC

PFI 6/AO START TRIG

CTR 1 OUT

PFI 3/CTR 1 SRC

PFI 1/AI REF TRIG

EXT STROBE

+5 V

D GND

P0.3

P0.2

P0.1

P0.0

AO GND

AO 1

AI SENSE

AI 7

AI 6

AI 5

AI 4

AI 3

AI 2

AI 1

AI 0

AI GND

FREQ OUT

PFI 7/AI SAMP CLK

PFI 5/AI SAMP CLK

PFI 2/AI CONV CLK

PFI 0/AI START TRIG

AI HOLD COMP

+5 V

PFI 9/CTR 0 GATE

PFI 4/CTR 1 GATE

P0.7

P0.6

P0.5

P0.4

D GND

AO 0

AI 15

AI 14

AI 13

AI 12

AI 11

AI 10

AI 9

AI 8

AI GND

+5 V

P1.0

P1.1

P1.2

P1.3

P1.4

P1.5

P1.6

P1.7

P2.0

P2.1

P2.2

P2.3

P2.4

P2.5

P2.6

P2.7

P3.0

P3.1

P3.2

P3.3

P3.4

P3.5

P3.6

P3.7

D GND

NI DAQPad-6016 OEM User Guide 4 ni.com

LEDs

The DAQPad-6016 OEM has two LEDs that reflect the state of the device.

The green READY LED indicates whether the device is powered on and

configured as a USB device. The yellow ACTIVE LED indicates whether

there is activity over the USB bus. Figure 3 shows the pins that connect the

LEDs to the device.

Figure 3. DAQPad-6016 OEM LEDs (111 mm ×163 mm Version)

The READY LED has two sets of pins. The first set of pins labeled 1a and

the resistor labeled R5 are used to connect to the onboard LED. The 220 Ω

R5 resistor drives enough current to power on the LED.

The second set of pins labeled 1b allow you to connect an external LED

circuit to the device. You can solder wires to these pins.

The set of pins labeled 2 and the 220 Ωresistor labeled R6 are used for the

ACTIVE LED. The ACTIVE LED does not have a separate set of pins to

connect to an external LED circuit.

1a–1a+

2–2+

Resistor to adjust

current through

ACTIVE LE

Resistor to adjust

current through

READY LED

Positive Connection

or REA

DY LE

atiNegative Connection

or REA

or READY LED

1b+ 1b–

+VE GND

E1 E2

Positive Connection for

External READY LED

Negative Connection

for ACTIVE LED

Positive Connection

for ACTIVE LED

Negative Connection for

External READY LED

©National Instruments Corporation 5 NI DAQPad-6016 OEM User Guide

Table 2 shows the schematics of the onboard ACTIVE and READY LEDs,

and how to connect an external READY LED circuit to the device.

Power Switch (111 mm ×163 mm Version)

The power switch on the DAQPad-6016 OEM powers the device on and

off. Figure 4 shows the pins on the power switch.

Figure 4. DAQPad-6016 OEM Power Switch (111 mm ×163 mm Version)

Table 2. Schematics of the DAQPad-6016 OEM LEDs

Onboard

ACTIVE LED

Onboard

READY LED

External READY

LED Circuit

2–

LED

1a+

1a–

LED

1b+

1b–

Switch

SW1

Provides

Power to

Device

VDC Comes

from Fuse

XF1

J10

Connects to

D GND

NI DAQPad-6016 OEM User Guide 6 ni.com

Pin 1 is connected to VDC through the fuse (reference designator XF1).

The VDC is the voltage provided by the power supply through the power

connector (reference designator J10) and must be 9–25 V.

Pin 2 provides power to the circuitry on the DAQPad-6016 OEM. When

the switch is in the On position, the VDC power supply from pin 1 is routed

to pin 2.

Pin 3 connects pin 2 to ground when the switch is in the Off position.

This allows the charge on the DAQPad-6016 OEM to leak to ground when

it is powered off.

Figure 5 shows a schematic of the switch.

Figure 5. Schematic of the DAQPad-6016 OEM Switch

NRSE/RSE Switch (111 mm ×163 mm Version)

The DAQPad-6016 OEM device can make differential or single-ended

analog input measurements.

In nonreferenced single-ended (NRSE) mode, the ground reference signal

is provided by the user on the AI SENSE pin. In referenced single-ended

(RSE) mode, the ground reference signal is AI GND, the ground of the

DAQPad-6016 OEM device.

SW1 XF1

FUSE

Power to

Device

J10

Power

Connector

©National Instruments Corporation 7 NI DAQPad-6016 OEM User Guide

Table 3 shows how to set the NRSE/RSE switch (S1).

Chassis Ground

Chassis ground provides a connection between the enclosure and USB

ground.

D GND is connected to the chassis ground at the bottom edge of the board

through two 0 Ωresistors. The chassis ground directly connects to USB

ground, which connects to earth ground. Figure 6 shows where the different

grounds are connected.

Table 3. NRSE/RSE (S1) Settings

Mode

Ground

Reference

Signal S1 Position

NI-DAQmx

Setting1

NRSE (default) AI SENSE NRSE

RSE AI GND NRSE2

1In NI-DAQmx, set the Analog Input Terminal Configuration property of your AI Task to this setting. For more information,

refer to the Analog Input Terminal Configuration topic in the E Series Help, available at ni.com/manuals.

2To make RSE measurements, you must set the Analog Input Terminal Configuration property of your AI Task to NRSE in

NI-DAQmx. Even though RSE mode is not exposed in the software, setting S1 to RSE and setting the Analog Input Terminal

Configuration property of your AI Task to NRSE will allow you to make RSE measurements.

NI DAQPad-6016 OEM User Guide 8 ni.com

Figure 6. DAQPad-6016 OEM Ground Connections (111 mm × 163 mm Version)

Device Components

Table 4 contains information about the components used for interfacing

and interacting with the NI DAQPad-6016 OEM.

Table 4. NI DAQPad-6016 OEM Components

Component

Reference

Designator(s)

on PCB Manufacturer

Manufacturer

Part Number

LEDs DS1 Dialight 553-0332

50-pin connectors J7, J8 3M 2550-6002UB

USB connector J9 AMP 787780-1

Power connector J10 Switchcraft 722RA

On/off switch SW1 ITT Industries, Cannon E101J1A3QE2

F 2A L 250V fuse XF1 Littelfuse 217.002

NRSE/RSE switch S1 EAO/SECME 09-03201-02

Chassis ground

connects to USB

cable gr

roun

Mounting hole connected

to chassis ground

Holes for USB connector pins

connected to chassis ground

Board ground

connects to

chassis ground

through 0 Ω

resistors

DAQPad-6016 OEM (191 mm ×163 mm Version)

Figure 7 shows the 191 mm ×163 mm version of the DAQPad-6016 OEM

device.

For specifications and more information about the DAQPad-6016 OEM

device, refer to the E Series Help at ni.com/manuals.

Figure 7. DAQPad-6016 OEM Device (191 mm ×163 mm Version)

Dimensions

Figure 8 shows the dimensions of the 191 mm ×163 mm version of the

DAQPad-6016 OEM device.

NI DAQPad-6016 OEM User Guide 10 ni.com

Figure 8. DAQPad-6016 OEM Dimensions in Inches and Millimeters

(191 mm × 163 mm Version)

0.515 (13.08)

0.215 (5.45)

4X Ø 0.125 (3.18)

0.055 (1.40)

7.563 (192.10)

0.262 (6.65)

0.436 (11.07)

0.392 (9.96)

0.000 (0)

0.393 (9.98) 0.390 (9.91)

0.800 (20.32)

3.220 (81.79)

5.600 (142.24)

6.100 (154.94)

5.930 (150.62)

1.057 (26.85)

2.145 (54.48)

2.606 (66.19)

3.296 (83.72)

6.400 (162.56)

5.850 (148.59)

0.200 (5.08)

0.000 (0)

–0.203 (–5.16)

0.304 (7.72)

3.730 (94.74)

7.250 (184.15)

7.500 (190.50)

3.080 (78.23)

4-40 Tapped

Pin 1

Pin 2

Pin 49

Pin 50

Pin 1

Pin 2

Pin 49

Pin 50

Full 50-Pin

I/O Connector

Extended DIO 50-Pin

I/O Connector

Table des matières

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur