Netvox Z311C Manuel utilisateur

ZigBeeTM- Wireless Window/Door Sensor

User Manual

Wireless Window Door Sensor

Model: Z311C

20131227

FW V2.0

HW V0.1-V1.1

Table of Contents

1. Introduction.............................................................................................................................................................3

2. Product Appearance.............................................................................................................................................4

3. Specification........................................................................................................................................................... 5

4. Installation Diagram..............................................................................................................................................5

5. Setting up Z311C................................................................................................................................................... 6

5.1. Turn On/ Turn Off Z311C............................................................................................................................... 6

5.2. Join the ZigBee Network................................................................................................................................ 6

5.3. Enroll in the ZigBee Security System.............................................................................................................7

5.4. Sleeping Mode................................................................................................................................................ 7

5.5. Wake up Z311C...............................................................................................................................................7

5-6. Door Window Contact Sensor........................................................................................................................ 7

5.7. HeartBeat Technique.......................................................................................................................................9

5.8. Battery............................................................................................................................................................. 9

5.9. Restore to Factory Setting...............................................................................................................................9

6. Home Automation Clusters for Z311C.......................................................................................................... 10

7. Important Maintenance Instructions.............................................................................................................12

1. Introduction

Netvox Z311C, a Window/Door Sensor and Glass Sensor, acts as an End Device in ZigBee network. It does not

perform permit-join function as a coordinator or a router for other devices to join the network. Z311C is featured to

play a role of the sensor (Zone device) in the ZigBee security system. It is installed for being the window/door

opening detector. Z311C will notify the central security unit, CIE (Control and Indicating Equipment) device, to

send commands to a siren device to trigger an alarm while the window/door is opened. When the window/door has

been closed, Z311C will send the normal-condition report to the CIE device.

What is ZigBee?

ZigBee is a short range wireless transmission technology based on IEEE802.15.4 standard and supports multiple

network topologies such as point-to-point, point-to-multipoint, and mesh networks. It is defined for a

general-purpose, cost-effective, low-power-consumption, low-data-rate, and easy-to-install wireless solution for

industrial control, embedded sensing, medical data collection, smoke and intruder warning, building automation

and home automation, etc.

2. Product Appearance

Magnetic Contact

Indicator (Red/ Green)

Binding Key

Auxiliary Key

Battery Cover

Extended Magnet

Extended Contact

Extended Contact Input

3. Specification

Fully IEEE 802.15.4 compliant

Utilizes 2.4GHz ISM band; up to 16 channels

Power supply: 2 x 3V CR2450 button cell batteries.

Operating consumption: ≤ Tx ≤ 43mA; Rx ≤ 28mA

Standby consumption: ≤ 3.5uA

Up to 70 meters wireless transmission range in non-obstacle space

Easy installation and configuration

4. Installation Diagram

Remove the battery cover, insert the batteries, and then mount the cover to complete the installation.

This device is NOT truly waterproof/ resistant and is for indoor use.

Installation: the distance between the body and the magnetic contact should be less than 2cm when the

door/window is closed.

5. Setting up Z311C

5.1. Turn On/ Turn Off Z311C

Under the circumstances Z311C is first time used or after resetting, when it is powered on and cannot

successfully search a network, Z311C will go into turn-off mode. Turn-off mode ensures the minimum power

consumption. Under this mode, any other buttons and contacts are not active except the binding key.

When Z311C had previously joined a ZigBee network, Z311C will go to turn-on mode and is ready to work in

the network after powering on it.

Users can also manually turn on or turn off Z311C using the following instructions:

A. Turn it on: Press the Binding Key once. The indicator will flash red once, and the device is ready to

be used.

B. Turn it off: Press the Binding Key once. The indicator will flash red 10 times in 5 seconds. Press the

Binding Key again within the 10 red flashes to turn the device off. Otherwise, while the key press is

not applied within 5 seconds, the device will be still in turn-on mode.

NOTE: We recommend that users remove the battery to power off Z311C when it is not indented to be used

for a long period of time.

5.2. Join the ZigBee Network

After Z311C is powered on, it will search for an existing ZigBee network and send a request to join the

network automatically. While Z311C is under the coverage from a coordinator or a router whose permit-join

feature is enabled, Z311C will be permitted to join the network. Typically, the default permit-join period of

time is 60 seconds. Please refer to the following steps to complete the join:

Step1. Restore Z311C back to the default factory setting (please refer to Chapter 5.9. Restore To Factory

Setting).

Step2. Enable the permit-join function (valid for 60 seconds) of a coordinator or a router (please refer to

the user manual of the coordinator or the router to enable the permit-join feature).

Step3. Turn on Z311C. It will start to search and join the network.

The indicator will flash green 5 times after it is joined successfully. Otherwise, the indicator will not flash.

Z311C will stop searching and go to turn-off mode when it doesn’t find a network to join in 15 seconds. Press

the Binding Key again to turn it on for searching and joining the network.

After joining a network, Z311C would try to enroll in the ZigBee security system. Please make sure

Z311C and CIE (Control and Indicating Equipment) device have enough power.

5.3. Enroll in the ZigBee Security System

Z311C is a Zone device in the ZigBee security system. Right after Z311C join the ZigBee network, it will

automatically find out a CIE (Control and Indicating Equipment) device (i.e. Netvox Z201B) and send a

registration request to the CIE device to enroll in the security system. The enrollment has these 3 situations:

A. There is no CIE device or no compatible CIE device in the network → the indicator flashes red twice.

B. There is a compatible CIE device in the network, but it is failed to enroll → the indicator flashes red 4

times. Users can press the Auxiliary Key to initiate the registration.

C. The enrollment is completed → the indicator flashes red 6 times.

NOTE: Users had better NOT enroll multiple Zone devices at the same time to prevent registration failure.

5.4. Sleeping Mode

Z311C is designed to go into sleeping mode for power-saving in some situations:

A. When it doesn’t find a network to join → Z311C will go to sleeping mode.

B. While the device is in the network → the sleeping period is 5 minutes; it will wake up every 5

minutes to keep online.

C. Once Z311C was joined to a network and by any chance the network is no longer existed or the

device is out of the network → Z311C will wake up every 15 minutes to find the network it joined

before. It never keeps in sleeping mode and continues to find its network every 15 minutes. This

condition would consume up to 30 times power spending compared to normal-operating status. To

prevent this unwanted power consumption, we recommend that users manually power off the device.

5.5. Wake up Z311C

When users would like to setup or acquire data from the device which is in sleeping mode, we have to wake

up the device as the following steps:

Step1. Press and hold both the Auxiliary Key and the Binding Key.

Step2. After the indicator flashes red twice, release both buttons.

Step3. The indicator will flash green 5 times while broadcasting the IP address and the IEEE address.

Z311C would be in active status for 2 minutes for communication.

5-6. Door Window Contact Sensor

Z311C’s Zone Type: Contact switch (ID: 0x0015)

The value of Alarm1 is 1 when the door/window is opened (the distance between the magnet and the

contact is more than 22cm).

The value of Alarm1 is 0 when the door/window is closed.

Under the circumstances that Z311C has enrolled to the security system, it will send the contact status to the

command center (and the bound devices with ID: 0x0500) after triggering. The Warning Device will send out

alarm sound or lighting alert for warning.

Under the circumstances that Z311C hasn’t enrolled to the security system, it will try enroll in a security

system after triggering. After the enrollment, Z311C will send the contact status to the command center.

ZoneStatusChange commands: 0x00.

The command list:

Bits:8 8 8 var

Frame

control

Transaction

Sequence

number

Command

identifer

Frame payload

16-Bit Enumeration 8-Bit Enumeration

0x09 0x00 ZoneStatus ExtendedStatus

（Clusterid：0x 0500）

Values of the ZoneStauts payload

ZoneStatus

Attribute Bit Number Meaning Values

0 Alarm1 1 – opened or alarmed

0 – closed or not alarmed

1 Alarm2 1 – opened or alarmed

0 – closed or not alarmed

2 Tamper 1 – Tampered

0 – Not tampered

3 Battery 1 – Low battery

0 – Battery OK

4 Supervision reports 1 – Reports

0 – Does not report

5 Restore reports 1 – Reports restore

0 – Does not report restore

6 Trouble 1 – Trouble/Failure

0 – OK

7 AC (mains) 1 – AC/Mains fault

0 – AC/Mains OK

8-15 Reserved

Values of the ExtendedStatus payload

ExtendedStatus

Attribute Bit Number Meaning Values

0-6 ZoneID

7 ZoneStatusChange Or Heartbeat 1 – HeartBeat

0 – ZoneStatusChange

5.7. HeartBeat Technique

In a security system, it is important that Zone devices report the conditions to the central security unit (the

CIE device). To meet this need, Netvox came up with a technique called “HeartBeat”.

Right after Z311C enrolls to a security system, it sends a HeartBeat signal to the CIE device. Afterward, it will

send HeartBeat data every hour by default settings.

5.8. Battery

Low-power report: The working voltage for Z311C is 2.1~3.6V. When the operating voltage is lower than

2.1V, Z311C will send a low-power report to the CIE device.

The related data:

Power configuration cluster (ID:0x0001)

Battery voltage attribute (ID:0x0020)

5.9. Restore to Factory Setting

While Z311C is unable to communicate with its enrolled CIE device or users would like Z311C to join a new

network, a factory reset is required. To restore it to factory setting, please follow the steps:

Step1. Press and hold both the Auxiliary Key and the Binding Key.

Step2. The indicator will flash red twice. Keep pressing and holding the both buttons.

Step3. Until the indicator starts flashing red again, release both buttons.

Step4. After 10 red flashes, it will go into turn-off mode.

After the factory restore, please refer to Chapter 5.1. Turn On/ Turn Off Z311C to setup it.

6. Home Automation Clusters for Z311C

A cluster is a set of related attributes and commands which are grouped together to provide a specific function. A

simple example of a cluster would be the On/Off cluster which defines how an on/off switch behaves. This table

lists the clusters which are supported by Z311C.

1.End Point(s)：0x01:

2.Device ID：IAS Zone（0x0402）

3.EndPoint Cluster ID

Cluster ID for Z311C

Server side Client side

EP 0x01 (Device ID: IAS Zone(0x0402) )

Basic(0x0000) None

Power configuration(0x0001)

Identify(0x0003)

commissioning( 0x0015)

IAS zone ( 0x0500)

Poll Control（0x0020）

Diagnostics（0x0B05）

This lists the attributes of the basic information.

Identifier Name Type Range Access Default Mandatory

/ Optional

0x0000 ZCLVersion Unsigned

8-bit integer

0x00 –

0xff

Read only 0x03 M

0x0001 ApplicationVersion Unsigned

8-bit integer

0x00 –

0xff

Read only 0x14 O

0x0002 StackVersion Unsigned

8-bit integer

0x00 –

0xff

Read only 0x33 O

0x0003 HWVersion Unsigned

8-bit integer

0x00 –

0xff

Read only 0x0A O

0x0004 ManufacturerName Character

string

0 – 32

bytes

Read only netvox O

0x0005 ModelIdentifier Character

string

0 – 32

bytes

Read only Z311CE3ED O

0x0006 DateCode Character

string

0 – 16

bytes

Read only 20131227 O

0x0007 PowerSource 8-bit

Enumeration

0x00 –

0xff

Read only 0x03 M

Table des matières

Autres manuels netvox Accessoires

netvox

netvox RA0708 Manuel utilisateur

netvox

netvox RB11E Manuel utilisateur

netvox

netvox R718NL3 Series Manuel utilisateur

netvox

netvox R718CXAB Manuel utilisateur

netvox

netvox ZigBee Z311G Manuel utilisateur

netvox

netvox R718F2 Manuel utilisateur

netvox

netvox R718EA Manuel utilisateur

netvox

netvox R311B Manuel utilisateur

netvox

netvox RA0716A Manuel utilisateur

netvox

netvox R311DA Manuel utilisateur

netvox

netvox R711 Manuel utilisateur

netvox

netvox R313DA Manuel utilisateur

netvox

netvox R718PE Manuel utilisateur

netvox

netvox R718DB2 Manuel utilisateur

netvox

netvox R313K Manuel utilisateur

netvox

netvox R718VA Manuel utilisateur

netvox

netvox R718DA Manuel utilisateur

netvox

netvox R718PA5 Manuel utilisateur

netvox

netvox R718PA11 Manuel utilisateur

netvox

netvox R72632A Manuel utilisateur

netvox

netvox R313DB Manuel utilisateur

netvox

netvox R718N1 Manuel utilisateur

netvox

netvox R718UBD Series Manuel utilisateur

netvox

netvox R718F Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur

netvox Z311C Manuel utilisateur

Manuels Accessoires populaires d'autres marques