NETGEAR ProSafe AX742 Manuel utilisateur

Installation Guide

ProSafe 24 Gigabit Ethernet Stacking Kit AX742

This product is used as a stacking link between two NETGEAR managed switches

that have auxiliary module slots such as the GSM7328S, GSM7352S, GSM7328FS,

and M5300 series switches. Each module can operate at 12 Gbps (half duplex) or

24 Gbps (full duplex). Two AX744 modules and a CX4 cable are provided to allow

connection between two switches.

Verify the Package Contents

• Two ProSafe® 24 Gigabit Ethernet AX744 modules

• One 1 m CX4 cable

• Installation guide

AX744AX744

CX4 cable Installation guide

Install a Module

The ProSafe 24 Gigabit Ethernet AX744 module fits into the module slot in

NETGEAR stacking switches. The module is set to stacking mode by default. See

the switch CLI or software administration manual for instructions to configure the

switch for use with the module.

The module bays are on the front or the rear panel of a switch depending on the

switch model.

Note: The AX744 module is not hot swappable. You must reboot the switch after

installing or removing a module.

To install a module:

1. Insert the module into one of the available module slots, pressing firmly to seat

the module.

2. Once the module is seated, tighten the two set screws to hold the module in

place.

3. Reboot the switch.

AX744

Module

slots

Remove a Module

Note: The AX744 module is not hot swappable. You must reboot the switch after

installing or removing a module.

To remove a module:

1. Loosen the two set screws on either side of the module front panel.

2. Remove the module by holding the screw posts and pulling evenly on the

module and sliding it out of the module slot.

3. Reboot the switch.

Connect Switches with the Stacking Cable

To connect two switches with the CX4 cable:

1. Insert one end of the CX4 cable provided into an AX744 module that has been

installed in one switch.

2. Insert the other end of the CX4 cable into an AX744 module installed in a

second switch.

3. Refer to the software administration guide for the host switch for instructions to

configure the switch for use with the AX744 module.

AX742v1h3_IG_2oct2012.fm Page 1 Thursday, October 4, 2012 11:03 AM

October 2012

This symbol appears in accordance with the European Union Directive 2002/96 on the Waste

Electrical and Electronic Equipment (the WEEE directive). If you dispose of this product in the

European Union, treat and recycle it in accordance with your jurisdiction’s laws that implement the

WEEE directive.

NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of

NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to

change without notice. Other brand and product names are registered trademarks or trademarks of their

For indoor use only in all EU countries and Switzerland.

For the complete EU Declaration of Conformity, visit

http://support.netgear.com/app/answers/detail/a_id/11621/.

Statement of Conditions: In the interest of improving internal design, operational function, and/or reliability,

NETGEAR reserves the right to make changes to the products described in this document without notice.

NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit

layout(s) described herein.

Specifications

Standard IEEE 802.3ak, 10GBASE-CX4

Dimensions (H x W x D) 1.20 in. x 2.92 in. x 6.13 in.

(30.5 mm x 74.1 mm x 155.7 mm)

Weight 0.317 lb (0.144 kg)

Operating temperature 32 –122ºF (0 – 50ºC)

Storage temperature 32 – 158ºF (0 –70ºC)

Operative relative humidity 10 – 90% noncondensing

Max. power consumption 0W

MTBF 885 years (at 25ºC); 252 years (at

55ºC)

Regulatory Compliance

Certificate of Manufacturer/Importer

It is hereby certified that the NETGEAR model AX744 has been suppressed in

accordance with the condition set out in MBPT-Amtsb|Vfg 243/1991 and vfg 46/

1992. The operation of some equipment (for example, test transmitters) in

accordance with regulation may, however, be subject to certain restrictions. Please

refer to the note in the operating instructions. Federal Office for Telecommunications

Approvals has been notified of the placing of this equipment on the market and has

been granted the right to test the series for compliance with regulation.

Note:This device has been tested and found to comply with limits for a Class A digital

device, pursuant to part 15 of FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a commercial installation.

Technical Support

After installing your device, locate the serial number on the label of your product and

use it to register your product at https://my.netgear.com.

You must register your product before you can use NETGEAR telephone support.

NETGEAR recommends registering your product through the NETGEAR website.

For product updates and web support, visit http://support.netgear.com.

You can get the hardware and software manuals for managed switches online at

http://downloadcenter.netgear.com or through a link in the switch user interface or

resource CD.

AX742v1h3_IG_2oct2012.fm Page 2 Thursday, October 4, 2012 11:03 AM

Table des matières

Autres manuels NETGEAR Matériel réseau

NETGEAR

NETGEAR WMS5316 - ProSafe 16-AP Wireless Management... Manuel utilisateur

NETGEAR

NETGEAR XAVBI 301 Manuel utilisateur

NETGEAR

NETGEAR AGM722F Manuel utilisateur

NETGEAR

NETGEAR UTM5 - ProSecure Unified Threat Management... Manuel utilisateur

NETGEAR

NETGEAR ProSafe UTM9S Guide de configuration rapide

NETGEAR

NETGEAR ReadyNAS RN312 Manuel utilisateur

NETGEAR

NETGEAR ProSecure UTM150 Manuel utilisateur

NETGEAR

NETGEAR GS716TP Manuel

NETGEAR

NETGEAR ProSafe ANT2409 Manuel utilisateur

NETGEAR

NETGEAR ReadyNAS 2120 Manuel utilisateur

NETGEAR

NETGEAR Orbi RBK50 Manuel utilisateur

NETGEAR

NETGEAR WN1000RP Manuel utilisateur

NETGEAR

NETGEAR Stora Manuel utilisateur

NETGEAR

NETGEAR ProSafe UTM9S Manuel utilisateur

NETGEAR

NETGEAR ProSafe UTM9S Manuel utilisateur

NETGEAR

NETGEAR AXM752 - ProSafe XFP Transceiver Module Manuel utilisateur

NETGEAR

NETGEAR RN12P0610 - ReadyNAS 3200 Instructions de montage

NETGEAR

NETGEAR STM150 - ProSecure Web And Email Threat Management... Manuel utilisateur

NETGEAR

NETGEAR Nighthawk Mesh WiFi 6 System Manuel utilisateur

NETGEAR

NETGEAR ProSafe UTM9S Manuel utilisateur

NETGEAR

NETGEAR RND2175 - ReadyNAS Duo NAS Server Manuel utilisateur

NETGEAR

NETGEAR Insight Instant AirBridge Manuel utilisateur

NETGEAR

NETGEAR RN12P0610 - ReadyNAS 3200 Manuel utilisateur

NETGEAR

NETGEAR MR60 Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur