National Instruments FieldPoint FP-2000 Manuel utilisateur

FP-2000/2010 FieldPoint Quick Start Guide

Install the Network Module

Panel MountDIN Rail Mount

A. Unlock rail clip.

Network Module

Mounting Hardware (DIN rail

or panel mount accessory)

Terminal Base(s)

·I/O Module(s)

·Power Supply

·Accessories: Ethernet cable,

screwdriver

·PC running Windows

·FieldPoint Software CD

·LabVIEW RT

What You Need to Get Set Up

You can mount your modules on a DIN rail or to a panel.

322759b.qxd 7/26/01 9:51 AM Page 1

B. Hook lip on back of module onto top

of DIN rail, press down, and snap

into place.

B. Snap panel mount accessory

(which you can order separately)

onto module.

Panel MountDIN Rail Mount

NOTE: Do not use spliced DIN

rails. Use only a single DIN rail.

C. Slide module into position and lock

rail clip.

C. Lock rail clip.

D. Use template that came with your

accessory to drill pilot holes and

mount module onto

panel using

accessory.

322759b.qxd 7/26/01 9:51 AM Page 2

Install the Terminal Base(s)

CAUTION: Terminal bases must be connected to the network module

before applying power to the module. Do

not

connect or disconnect

terminal bases while power is applied to the network module.

DIN Rail Mount

A. Unlock rail clip.

B. Press base onto rail.

Panel Mount

A. Use template that came with your

accessory to drill pilot holes.

B. Connect terminal base to network

module connector, being careful not

to bend any connector pins.

C. Fasten terminal base to panel.

322759b.qxd 7/26/01 9:51 AM Page 3

DIN Rail Mount Panel Mount

D. Repeat for each terminal base, up

to nine for each network module in

most cases. You can use one or

two extender cables (which you can

order separately) if your FieldPoint

bank is too long for your available

space.

E. Place protective cover on last base,

and install rail locks at each end.

C. Slide into position and lock the rail

clip. Be careful not to bend any pins. D. Repeat for each terminal base, up to

nine for each network module in

most cases. You can use one or two

extender cables (which you can order

separately) if your FieldPoint bank is

too long for your available space.

E. Place protective cover on last base.

322759b.qxd 7/26/01 9:52 AM Page 4

Install the I/O Module(s)

A. Align slots on module with guide rails on

base, and press onto base until terminal

base’s latch locks the module in place.

B. Repeat for each I/O module.

It does not matter where you install each I/O module, except for

these types of situations:

··

·· If you plan to cascade power between any I/O modules using the

V and C terminals, those modules should be grouped together.

··

·· For more accurate measurements, you might want to locate any

thermocouple modules away from heat sources, including network

modules or relay modules, unless you are mounting them on an FP-TB-3.

Connect the Network Cables

Connect the FP-2000/2010 to an Ethernet network by connecting the RJ-45

Ethernet port of the FP-2000/2010 to an Ethernet hub using a standard

Category 5 Ethernet cable.

Straight-Through

UTP Cable

Straight-Through

UTP Cable

322759b.qxd 7/26/01 9:52 AM Page 5

Do not use a cable longer than 100 m. If you are using a 100 Mbps Ethernet,

National Instruments recommends using a Category 5 shielded twisted-pair

Ethernet. If you need to build your own cable, refer to the

FP-2000/2010

User Manual

specifications section for cabling details.

Wire Power to Your FieldPoint System

A. Connect 12-30 VDC power supply leads to V and C terminals of the

network module. If you want to verify that your power supply is sufficient

for your modules and devices, refer to the

FP-2000/2010 User Manual

for

instructions on calculating power requirements.

B. Connect power to the FieldPoint modules that require external power for

outputs (output modules, counter modules, PWM, PG, QUAD). Refer to

the I/O module’s operating instructions for power requirement details.

You can power a module by connecting the V and C inputs on its terminal

base to a separate power supply, connecting the V and C outputs of a

neighboring terminal base or network module, or using a combination of

both methods. If you want to power field I/O devices from a terminal

base, supply power to the terminal base, and then connect the terminal

base V and C output terminals to the field device.

Optionally, you can connect an FP-2000/2010 directly to a computer using an

Ethernet crossover cable.

Cross-Over Cable

322759b.qxd 7/26/01 9:52 AM Page 6

CAUTION: Cascading power from neighboring bases or network modules

defeats isolation between cascaded modules.

15 16 V

31 32 C

V132

C17 18

CAUTION: Cascading

power defeats isolation.

Shades of gray indicate

different voltage potentials.

Separate Power Supply

(Recommended)

Cascaded Power

(Reduces Isolation)

FP-2000 FP-AI-100 FP-AO-200 FP-RLY-420 FP-TC-120

No External

Power Required

322759b.qxd 7/26/01 9:52 AM Page 7

Connect to Field Devices

Use each I/O module’s operating instructions, or the diagram under its

removable label, to help you connect your field devices.

FP-AI-110

Self-Powered

Floating Sensor

15 32

Loop-Powered

Sensor

17 2

ISensor

Channel 0

VSensor

Channel 7

To Po w e r

Supply

NOTE: Either the self-powered

sensor or power supply should be

floating (not tied to earth ground).

322759b.qxd 7/26/01 9:52 AM Page 8

Power Up Your FieldPoint System

CAUTION: Terminal bases must be connected to the FP-2000/2010

before power is applied to the FP-2000/2010.

Plug in each power supply

to your FieldPoint bank. You

should see the POWER and

STATUS LEDs come on. After

about 5 seconds, the STATUS

LED begins flashing, one flash

at a time. This indicates that

the FP-2000/2010 is ready to

be configured. (If the STATUS

LED turns off, and the A, B, C,

and DLEDs come on, the FP-2000/2010 has been configured and LabVIEW

RT is starting up.) If the LEDs do not follow this sequence, refer to the

FP-2000/2010 User Manual

troubleshooting appendix.

After the hardware is installed, you should verify communication, configure

the modules, and configure your power-up states and watchdog settings.

If you are using National Instruments FieldPoint software for these tasks,

continue to the following section.

322759b.qxd 7/26/01 9:52 AM Page 9

Install the FieldPoint Software

A. Close all other applications. If you

plan to install National Instruments

development software such as

Lookout, LabVIEW, or Measurement

Studio, install them before you

install the FieldPoint software.

B. Insert the FieldPoint software CD and follow the onscreen instructions.

Configure the FP-2000/2010

Refer to the

FP-2000/2010 User Manual

for more information about

configuration settings.

A. Select Start»Programs»National Instruments FieldPoint»FieldPoint Explorer.

B. Click the +to expand the view.

C. Right-click on the

FieldPoint icon and

select Add a comm

resource to this

server.

322759b.qxd 7/26/01 9:52 AM Page 10

Autres manuels pour FieldPoint FP-2000

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels National Instruments Unité de contrôle

National Instruments

National Instruments NI 6013 Guide de démarrage rapide

National Instruments

National Instruments FP-RLY-422 Manuel utilisateur

National Instruments

National Instruments SCXI-1104/C Manuel

National Instruments

National Instruments NI 9246 Manuel

National Instruments

National Instruments NI 9264 Manuel utilisateur

National Instruments

National Instruments FieldPoint FP-AO-210 Manuel utilisateur

National Instruments

National Instruments PXIe-4466 Manuel utilisateur

National Instruments

National Instruments NI PXI-665 Series Manuel utilisateur

National Instruments

National Instruments VXI-AO-48XDC Manuel utilisateur

National Instruments

National Instruments FP-AI-102 Manuel utilisateur

National Instruments

National Instruments NI 9478 Manuel utilisateur

National Instruments

National Instruments FieldPoint FP-AI-110 Manuel utilisateur

National Instruments

National Instruments PXIe-8821 Manuel utilisateur

National Instruments

National Instruments NI 9218 Manuel utilisateur

National Instruments

National Instruments NI TB-4300B Manuel

National Instruments

National Instruments sbRIO-9205 Manuel utilisateur

National Instruments

National Instruments PXI-2568 Manuel utilisateur

National Instruments

National Instruments SCXI-1581 Manuel utilisateur

National Instruments

National Instruments PXI-6682 Series Manuel utilisateur

National Instruments

National Instruments NI-9477 Manuel utilisateur

National Instruments

National Instruments R Series Manuel utilisateur

National Instruments

National Instruments NI-9208 Manuel utilisateur

National Instruments

National Instruments NI PXI-6682 Manuel utilisateur

National Instruments

National Instruments SCXI-1181K Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur