National Instruments 9861 Manuel utilisateur

GETTING STARTED GUIDE

NI 9861

1-Port, Low-Speed/Fault Tolerant CAN Module

Français Deutsch 日本語 한국어 简体中文

ni.com/manuals

This document explains how to connect to the NI 9861.

The NI 9861 module requires the latest NI-XNET software to be

installed. The latest version of the NI-XNET software is at

ni.com/downloads.

Note Before you begin, complete the software and

hardware installation procedures in your chassis

documentation.

Note The guidelines in this document are specific to

the NI 9861. The other components in the system might

not meet the same safety ratings. Refer to the

documentation for each component in the system to

determine the safety and EMC ratings for the entire

system.

Safety Guidelines

Operate the NI 9861 only as described in this document.

Hot Surface This icon denotes that the component

may be hot. Touching this component may result in

bodily injury.

2| ni.com | NI 9861 Getting Started Guide

Caution Do not operate the NI 9861 in a manner not

specified in this document. Product misuse can result in

a hazard. You can compromise the safety protection

built into the product if the product is damaged in any

way. If the product is damaged, return it to NI for

repair.

Safety Guidelines for Hazardous Locations

The NI 9861 is suitable for use in Class I, Division 2, Groups A,

B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4

and Ex nA IIC T4 hazardous locations; and nonhazardous

locations only. Follow these guidelines if you are installing the

NI 9861 in a potentially explosive environment. Not following

these guidelines may result in serious injury or death.

Caution Do not disconnect I/O-side wires or

connectors unless power has been switched off or the

area is known to be nonhazardous.

Caution Do not remove modules unless power has

been switched off or the area is known to be

nonhazardous.

NI 9861 Getting Started Guide | © National Instruments | 3

Caution Substitution of components may impair

suitability for Class I, Division 2.

Caution For Division 2 and Zone 2 applications,

install the system in an enclosure rated to at least IP54

as defined by IEC/EN 60079-15.

Caution For Zone 2 applications, install a protection

device between the CAN signals and the NI 9861 CAN

pins. The device must prevent the CAN Port-to-COM

voltage from exceeding 55 V if there is a transient

overvoltage condition.

Special Conditions for Hazardous Locations Use in

Europe and Internationally

The NI 9861 has been evaluated as Ex nA IIC T4 Gc equipment

under DEMKO Certificate No. 07 ATEX 0626664X and is

IECEx 14.0089X certified. Each NI 9861 is marked II 3G and

is suitable for use in Zone 2 hazardous locations, in ambient

temperatures of -40 °C ≤ Ta ≤ 70 °C. If you are using the NI 9861

in Gas Group IIC hazardous locations, you must use the device in

an NI chassis that has been evaluated as Ex nC IIC T4, Ex IIC

T4, Ex nA IIC T4, or Ex nL IIC T4 equipment.

4| ni.com | NI 9861 Getting Started Guide

Caution You must make sure that transient

disturbances do not exceed 140% of the rated voltage.

Caution The system shall only be used in an area of

not more than Pollution Degree 2, as defined in

IEC 60664-1.

Caution The system shall be mounted in an

ATEX/IECEx-certified enclosure with a minimum

ingress protection rating of at least IP54 as defined in

IEC/EN 60079-15.

Caution The enclosure must have a door or cover

accessible only by the use of a tool.

Wiring the NI 9861

The NI 9861 has one 9-pin male D-Sub connector that provides

connections to a CAN bus. The NI 9861 has pins for CAN_H and

CAN_L, to which you connect the CAN bus signals. Connect

these signals using twisted-pair cable.

The port has two isolated common pins (COM) that are internally

connected to the module’s isolated reference and serve as the

NI 9861 Getting Started Guide | © National Instruments | 5

reference ground for CAN_H and CAN_L. You can connect the

CAN bus reference ground (sometimes referred to as CAN_V-) to

one or both COM pins. The port also has an optional shield pin,

SHLD, that you can connect to a shielded CAN cable.

Connecting SHLD may improve signal integrity and EMC

performance in a noisy environment.

Caution You must use a UL listed ITE power supply

marked LPS with the NI 9861.

The NI 9861 requires an external power supply of +9 to +30 V to

operate. Supply power from the CAN bus to the VSUP pin.

Note Power on VSUP is required for CAN operation.

The NI 9861 pinout is listed in Table 1.

6| ni.com | NI 9861 Getting Started Guide

Table 1. Pin Assignments for the NI 9861

Connector Pin Signal

1 No Connection (NC)

2 CAN_L

3 COM

4 NC

5 SHLD

6 COM

7 CAN_H

8 NC

9 VSUP

CAN Bus Topology and Termination

A CAN bus consists of two or more CAN nodes cabled together.

The CAN_H and CAN_L pins of each node are connected to the

NI 9861 Getting Started Guide | © National Instruments | 7

main CAN bus cable through a short connection known as a

“stub.” The pair of signal wires, CAN_H and CAN_L, constitutes

a transmission line. Every device on a low-speed/fault-tolerant

CAN network requires a termination resistor for each CAN data

line: RRTH for CAN_H and RRTL for CAN_L.

Figure 1 shows a simplified diagram of a low-speed/fault-tolerant

CAN bus with termination resistor placements.

Figure 1. CAN Bus Topology and Termination Resistor Locations

RTL CAN_L RTH CAN_H RTL CAN_L RTH CAN_H RTL CAN_L RTH CAN_H

CAN_H

CAN_L

Low-speed/Fault-Tolerant

CAN Device

Low-speed/Fault-Tolerant

CAN Device

Low-speed/Fault-Tolerant

CAN Device

8| ni.com | NI 9861 Getting Started Guide

Connecting a CAN Bus to the NI 9861

You can connect each port of the NI 9861 to any location on a

CAN bus. Figure 2 shows one example of connecting the

NI 9861 directly to one CAN node.

Figure 2. Connecting Both Ports of the NI 9861 to CAN Buses

NI 9861

CAN Device

CAN

Cable

(With

Optional

Shield)

(SHLD)

CAN_H

CAN_L

Vsup

COM

(SHLD)

CAN_H

CAN_L

Vsup

COM

NI 9861 Getting Started Guide | © National Instruments | 9

Cabling Requirements for the NI 9861

Cable Specifications

Cables should meet the physical medium requirements specified

in ISO 11898, shown in the following table. Belden cable

(3084A) meets all these requirements and should be suitable for

most applications.

Table 2. ISO 11898 Specifications for Characteristics of a CAN_H and

CAN_L Pair of Wires

Characteristic Value

Length-related resistance 90 mΩ/m nominal

Length-related capacitance: CAN_L and ground,

CAN_H and ground, CAN_L and CAN_H

30 pF/m nominal

10 | ni.com | NI 9861 Getting Started Guide

Table des matières

Autres manuels National Instruments Unité de contrôle

National Instruments

National Instruments PXIe-5694 Manuel utilisateur

National Instruments

National Instruments PC/104-GPIB Manuel utilisateur

National Instruments

National Instruments 7340 PCI Manuel utilisateur

National Instruments

National Instruments NI 9234 Manuel utilisateur

National Instruments

National Instruments NI PXIe-7976R Manuel utilisateur

National Instruments

National Instruments 9512 C Series Manuel utilisateur

National Instruments

National Instruments 9246 Manuel utilisateur

National Instruments

National Instruments NI 9751 Manuel utilisateur

National Instruments

National Instruments NI 9225 Manuel

National Instruments

National Instruments PXIe-4340 Manuel utilisateur

National Instruments

National Instruments NI 9234 Manuel

National Instruments

National Instruments NI 9425 Manuel utilisateur

National Instruments

National Instruments NI 9401 Manuel utilisateur

National Instruments

National Instruments Module SCXI-1125 Manuel utilisateur

National Instruments

National Instruments FieldPoint FP-1001 Manuel utilisateur

National Instruments

National Instruments PXI-6682 Series Manuel utilisateur

National Instruments

National Instruments VMEpc 600 series Manuel utilisateur

National Instruments

National Instruments ISM-7400 Manuel utilisateur

National Instruments

National Instruments NI 9263 Manuel

National Instruments

National Instruments PXIe-8246 Manuel utilisateur

National Instruments

National Instruments SCC-LP Series Manuel utilisateur

National Instruments

National Instruments NI DCM-2316 Manuel utilisateur

National Instruments

National Instruments PXI-2568 Manuel utilisateur

National Instruments

National Instruments PXIe-7902 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur