National Instruments SCXI-1181K Manuel utilisateur

371063A-01 © 1994 National Instruments Corporation. All rights reserved August 1998

Installation Guide

SCXI-1181K Custom Module Assembly

This guide documents the contents of your SCXI-1181K custom module assembly kit and

includes illustrations of the circuit board specifications and the module assembly.

Introduction

The SCXI-1181K custom module assembly kit includes the unassembled components you need

to build a custom SCXI module, but not the actual circuit board. All of the mechanical

components of an SCXI module, such as the metal enclosure, front and back panels, and

connectors, are included.

The SCXI-1181K is intended for developers of custom SCXI modules who design and lay out

custom circuit boards for modules. For prototyping or building low-volume custom SCXI

modules, the fully assembled SCXI-1181 breadboard moduleis more appropriate.

What Your Kit Should Contain

The SCXI-1181K custom module assembly kit (part number 776572-81K) contains the

components listed in the following table. The reference numbers in the left column of the table

refer to callouts in Figure 1.

Reference

Number Component Quantity

1 Module front panel 1

2

3 Thumb screw, 2.5 mm 2

4 #4 x 5/16 in. Phillips screw, flat head 2

5 Enclosure base 1

6 Module rear panel 1

7 #4 x 5/16 in. Phillips screw, pan head 3

8 Enclosure cover 1

9 Identification label 1

J1 3 x 32 position Deutsche Industrie Norme

connector header 1

J2 50 position connector header 1

P1 4 x 6, 2 mm connector, push-fit 4

— Installation guide 1

1

Module front panel overlay

SCXI-1181K Custom Module Assembly Install. Guide 2 © National Instruments Corporation

Refer to the reference numbers of the components in the previous table and the corresponding

components in Figure 1 for module assembly.

Note: The four P1 connectors have a push-fit peg. Secure the P1 connectors to the printed

wire circuit board (PWB) by pushing the connector onto the PWB so that the middle

peg of the connector presses into the 0.081 in. hole in the PWB. National Instruments

recommends using the push-fit peg hand tool (part number CTHT-200) manufactured

by ITT Cannon for this installation. You can contact ITT Cannon at (800) 845-7000.

Figure 2 shows the SCXI module PWB outline.

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels National Instruments Unité de contrôle

National Instruments

National Instruments NI 9436 Manuel utilisateur

National Instruments

National Instruments SCXI -1122 Manuel

National Instruments

National Instruments PXImc Series Manuel utilisateur

National Instruments

National Instruments NI 9751 Manuel utilisateur

National Instruments

National Instruments SCXI-1581 Manuel utilisateur

National Instruments

National Instruments Module SCXI-1125 Manuel

National Instruments

National Instruments SCC-CTR01 Manuel utilisateur

National Instruments

National Instruments 9756 Manuel utilisateur

National Instruments

National Instruments PXIe-6594 Manuel utilisateur

National Instruments

National Instruments PXIe-5693 Manuel utilisateur

National Instruments

National Instruments NI PXIe-4300 Manuel utilisateur

National Instruments

National Instruments NI 4472 Manuel utilisateur

National Instruments

National Instruments NI 9269 Manuel utilisateur

National Instruments

National Instruments NI 9758 Manuel utilisateur

National Instruments

National Instruments NI PXI-665 Series Manuel utilisateur

National Instruments

National Instruments REM-11178 Manuel utilisateur

National Instruments

National Instruments FIeldPoint FP-AO-200 Manuel utilisateur

National Instruments

National Instruments NI PXIe-7975R Manuel utilisateur

National Instruments

National Instruments NI PXI-6682 Manuel utilisateur

National Instruments

National Instruments SCC-LP Series Manuel utilisateur

National Instruments

National Instruments cFP-RLY-421 Manuel utilisateur

National Instruments

National Instruments Module SCXI-1503 Manuel

National Instruments

National Instruments NI 9246 Manuel utilisateur

National Instruments

National Instruments NI 9871 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur