National Instruments NI 8234 Manuel utilisateur

Getting Started with the NI 8234

The NI 8234 is a Gigabit Ethernet (GigE) interface device for PXI Express (PXIe) or CompactPCI

Express (cPCIe). This document describes how to install and configure the necessary hardware and

software components to begin using the NI 8234.

What You Need to Get Started

You need the following items to set up and use the NI 8234.

❑NI 8234 GigE interface device

❑GigE Vision compliant camera

❑Ethernet cable

❑PXIe/cPCIe computer running Microsoft Windows Vista/XP/2000 with at least one available slot

Note The NI 8234 card will work in any standard peripheral slot of a cPCIe chassis adhering to the

PICMG CompactPCI Express EXP.0 R1.0 specification, or in a peripheral slot of a PXIe chassis that

is compatible with the PXI Express Hardware Specification, Revision 1.0 or later.

Note Visit ni.com/info and enter rdvisionvista for more information about

National Instruments image acquisition device compatibility with Windows Vista.

❑NI Vision Acquisition Software 8.2.1 or later, which includes the NI-IMAQdx driver software

❑Optional software for developing applications:

– NI Vision Builder for Automated Inspection

– NI Vision Development Module

–LabVIEW

– LabWindows™/CVI™

– Microsoft Visual Basic

Related Documentation

The following documents contain additional information that you may find helpful:

•NI Vision Acquisition Software Release Notes—Outlines new functionality, system requirements,

installation procedures, and descriptions of the documentation included with the NI-IMAQdx

driver software.

•Measurement & Automation Explorer Help for NI-IMAQdx—Describes how to configure the

NI-IMAQdx driver software, NI interface devices, and cameras using Measurement & Automation

Explorer (MAX).

•NI-IMAQdx Help—Contains fundamental programming concepts for the NI-IMAQdx driver

software.

Getting Started with the NI 8234 2 ni.com

Safety Information

Caution The following paragraphs contain important safety information you must follow when

installing and operating the device.

Do not operate the device in a manner not specified in the documentation. Misuse of the device may

result in a hazard and may compromise the safety protection built into the device. If the device is

damaged, turn it off and do not use it until service-trained personnel can check its safety. If necessary,

return the device to National Instruments for repair.

Keep away from live circuits. Do not remove equipment covers or shields unless you are trained to do

so. If signal wires are connected to the device, hazardous voltages can exist even when the equipment is

turned off. To avoid a shock hazard, do not perform procedures involving cover or shield removal unless

you are qualified to do so. Disconnect all field power prior to removing covers or shields.

If the device is rated for use with hazardous voltages (>30 Vrms, 42.4 Vpk, or 60 Vdc), it may require a

safety earth-ground connection wire. Refer to the device specifications for maximum voltage ratings.

Because of the danger of introducing additional hazards, do not install unauthorized parts or modify the

device. Use the device only with the chassis, modules, accessories, and cables specified in the

installation instructions. All covers and filler panels must be installed while operating the device.

Do not operate the device in an explosive atmosphere or where flammable gases or fumes may be

present. Operate the device only at or below the pollution degree stated in the specifications. Pollution

consists of any foreign matter—solid, liquid, or gas—that may reduce dielectric strength or surface

resistivity. The following is a description of pollution degrees.

• Pollution Degree 1—No pollution or only dry, nonconductive pollution occurs. The pollution has

no effect.

• Pollution Degree 2—Normally only nonconductive pollution occurs. Occasionally, nonconductive

pollution becomes conductive because of condensation.

• Pollution Degree 3—Conductive pollution or dry, nonconductive pollution occurs. Nonconductive

pollution becomes conductive because of condensation.

Clean the device and accessories by brushing off light dust with a soft, nonmetallic brush. Remove other

contaminants with a stiff, nonmetallic brush. The unit must be completely dry and free from

contaminants before returning it to service.

Yo u must insulate signal connections for the maximum voltage for which the device is rated. Do not

exceed the maximum ratings for the device. Remove power from signal lines before connection to or

disconnection from the device.

Caution National Instruments measurement products may be classified as either Measurement

Category I or II. Operate products at or below the Measurement Category level specified in the

hardware specifications.

Measurement Category1: Measurement circuits are subjected to working voltages2and transient

stresses (overvoltage) from the circuit to which they are connected during measurement or test.

Measurement Category establishes standardized impulse withstand voltage levels that commonly occur

1 Measurement Categories as defined in electrical safety standard IEC 61010-1.

2 Working voltage is the highest rms value of an AC or DC voltage that can occur across any particular insulation.

©National Instruments Corporation 3 Getting Started with the NI 8234

in electrical distribution systems. The following is a description of Measurement (Installation1)

Categories:

• Measurement Category I is for measurements performed on circuits not directly connected to the

electrical distribution system referred to as MAINS2voltage. This category is for measurements of

voltages from specially protected secondary circuits. Such voltage measurements include signal

levels, special equipment, limited-energy parts of equipment, circuits powered by regulated

low-voltage sources, and electronics.

• Measurement Category II is for measurements performed on circuits directly connected to the

electrical distribution system. This category refers to local-level electrical distribution, such as that

provided by a standard wall outlet (e.g., 115 V for U.S. or 230 V for Europe). Examples of

Measurement Category II are measurements performed on household appliances, portable tools,

and similar products.

• Measurement Category III is for measurements performed in the building installation at the

distribution level. This category refers to measurements on hard-wired equipment such as

equipment in fixed installations, distribution boards, and circuit breakers. Other examples are

wiring, including cables, bus-bars, junction boxes, switches, socket-outlets in the fixed installation,

and stationary motors with permanent connections to fixed installations.

• Measurement Category IV is for measurements performed at the primary electrical supply

installation (<1,000 V). Examples include electricity meters and measurements on primary

overcurrent protection devices and on ripple control units.

Unpacking

The NI 8234 ships in an antistatic package to prevent electrostatic discharge from damaging device

components. To avoid such damage in handling the device, take the following precautions:

1. Ground yourself using a grounding strap or by touching a grounded object, such as the computer

chassis.

2. Touch the antistatic package to a metal part of the chassis before removing the device from the

package.

Caution Never touch the exposed pins of connectors.

3. Remove the device from the package and inspect the device for loose components or any sign of

damage. Notify NI if the device appears damaged in any way. Do not install a damaged device into

the PXIe/cPCIe chassis.

Store the NI 8234 in the antistatic package when not in use.

Installation

The following instructions are for general installation. Refer to the documentation provided by your

computer manufacturer for specific instructions and warnings. Refer to the Specifications section for a

list of the typical power requirements for the NI 8234.

1. Install the NI Vision Acquisition Software before installing the NI 8234. Refer to the NI Vision

Acquisition Software Release Notes for specific installation instructions.

2. Power off and unplug the PXIe/cPCIe chassis.

1 Measurement Category is also referred to as Installation Category.

2 MAINS is defined as the (hazardous live) electrical supply system to which equipment is designed to be connected for the

purpose of powering the equipment. Suitably rated measuring circuits may be connected to the MAINS for measuring

purposes.

Getting Started with the NI 8234 4 ni.com

Caution To protect yourself and the computer from electrical hazards, the chassis must remain

unplugged until the installation is complete.

Note If you are using a PXIe chassis, the NI 8234 must be installed in a PXIe or hybrid peripheral

slot. Consult your PXI chassis manual for the location of these slots.

3. Touch a metal part of the chassis to discharge any static electricity that might be on your clothes or

body. Static electricity can damage the device.

4. Make sure the injector/ejector handle is in its downward position. Be sure to remove all connector

packaging and protective caps from retaining screws on the module. Align the NI 8234 with the

card guides on the top and bottom of the peripheral slot.

Caution Do not raise the injector/ejector handle as you insert the NI 8234. It will not insert properly

unless the handle is in its downward position so that it does not interfere with the injector/ejector rail

on the chassis, as shown in Figure 1.

5. Hold the handle as you slowly slide the module into the chassis until the handle catches on the

injector/ejector rail.

Caution Installing a PXIe/cPCIe device into a non-PXIe/cPCIe slot can damage both the chassis

motherboard and the device. If you are unsure of the differences between the connector types, do not

install the device. Refer to the documentation provided by your chassis manufacturer to determine

the correct slot in which to install the NI 8234.

Figure 1. NI 8234 Installation

6. Raise the injector/ejector handle until the module firmly seats into the backplane receptacle

connectors. The front panel of the NI 8234 should be even with the front panel of the chassis.

7. Tighten the bracket-retaining screws on the top and bottom of the front panel to secure the NI 8234

to the chassis.

1 PXI Express/CompactPCI Express Chassis

2 Ejector Handle

3 Screws

4 Chassis Slot Markings

NI PXIe-1062Q

©National Instruments Corporation 5 Getting Started with the NI 8234

8. Connect the Ethernet cable to your camera. Refer to your camera manufacturer documentation for

specific instructions about how to connect the cable to your camera.

9. Connect the Ethernet cable to one of the RJ-45 connectors on the NI 8234 front panel.

10. Plug in and power on the PXIe/cPCIe chassis.

The NI 8234 is now installed and the camera is connected.

Configuring the NI 8234

After you have installed the NI 8234 and powered on your computer, Windows will recognize the device

and assign resources to it. Use Measurement & Automation Explorer (MAX), the National Instruments

configuration utility, to configure a GigE Vision compliant camera connected to the NI 8234 for

acquisition. Refer to the Measurement and Automation Explorer Help for NI-IMAQdx for more

information about how to configure the NI 8234.

Note Before configuring the device in MAX, ensure that you installed the NI-IMAQdx driver

software.

Specifications

The following specifications apply to the NI 8234 interface device. These specifications are typical at

25 °C, unless otherwise stated.

Physical Characteristics

Dimensions ............................................................10.0 cm ×16.0 cm (3.9 in. ×6.2 in.)

Camera interface .................................................... Two RJ-45 connectors

Slot requirements ................................................... One peripheral slot supporting a x4 PCIe connection

(either PXIe/cCPIe slot or PXIe hybrid slot)

CompactPCI Express compliance.......................... Version 1.0a

Compatibility ......................................................... PXI Express Specification 1.0

CompactPCI Express Specification 1.0

Weight ....................................................................158 g (5.5 oz)

Native link width....................................................x4

Signaling

Ethernet..................................................................1000Base-T compliant on four pairs of Category 5

cable

Power Requirements

Typical....................................................................0.375 A at 3.3V

0.36 A at 5V

1.19 A at 1.8V

5.2 W maximum

Getting Started with the NI 8234 6 ni.com

Environment

The NI 8234 is intended for indoor use only.

Ambient temperature range ...................................0 to 50 °C

Operating relative humidity ...................................10 to 90%, noncondensing

Pollution Degree ....................................................2

Caution Do not use the NI 8234 for connection to signals within Measurement Categories II, III,

or IV.

Approved at altitudes up to 2,000 m.

Storage Environment

Ambient temperature range ...................................–40 to 70 °C

Relative humidity...................................................10 to 90%, noncondensing

Safety

This product is designed to meet the requirements of the following standards of safety:

• IEC 60950-1, EN 60950-01

• UL 60950-1, CSA 60950-1

Electromagnetic Compatibility

This product is designed to meet the requirements of the following standards of EMC for electrical

equipment for measurement, control, and laboratory use:

• EN 61326 EMC requirements; Minimum Immunity

• EN 55011 Emissions; Group 1, Class A

• CE, C-Tick, ICES, and FCC Part 15 Emissions; Class A

Note For EMC compliance, operate this device to product documentation.

CE Compliance

This product meets the essential requirements of applicable European Directives, as amended for

CE marking, as follows:

• 73/23/EEC; Low-Voltage Directive (safety)

• 89/336/EEC; Electromagnetic Compatibility Directive (EMC)

Note Refer to the Declaration of Conformity (DoC) for this product for any additional

regulatory compliance information. To obtain the DoC for this product, visit ni.com/

certification, search by model number or product line, and click the appropriate link in

the Certification column.

©National Instruments Corporation 7 Getting Started with the NI 8234

FCC Class B User Information

This equipment has been tested and found to comply with the limits for the class B digital device

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. The equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation.

If this equipment does cause harmful interference to television or radio reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following means:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution If the device is changed or modified, the user may void his or her authority to operate the

equipment.

Note This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Note Refer to the Declaration of Conformity (DoC) for this product for any additional regulatory

compliance information. To obtain the DoC for this product, visit ni.com/certification,

search by model number or product line, and click the appropriate link in the Certification column.

Environmental Management

National Instruments is committed to designing and manufacturing products in an environmentally

responsible manner. NI recognizes that eliminating certain hazardous substances from our products is

beneficial not only to the environment but also to NI customers.

For additional environmental information, refer to the NI and the Environment Web page at

ni.com/environment. This page contains the environmental regulations and directives with which

NI complies, as well as other environmental information not included in this document.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers At the end of their life cycle, all products must be sent to a WEEE recycling center.

For more information about WEEE recycling centers and National Instruments WEEE initiatives,

visit ni.com/environment/weee.htm.

⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑

RoHS

Ё೑ᅶ᠋

National Instruments ヺড়Ё೑⬉ᄤֵᙃѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ (RoHS)Ǆ

݇Ѣ National Instruments Ё೑ RoHS ড়㾘ᗻֵᙃˈ䇋ⱏᔩ ni.com/environment/rohs_chinaǄ

(For information about China RoHS compliance, go to ni.com/environment/rohs_china.)

National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation.

Refer to the Terms of Use section on ni.com/legal for more information about National

Instruments trademarks. Other product and company names mentioned herein are trademarks or trade

names of their respective companies. For patents covering National Instruments products, refer to the

appropriate location: Help»Patents in your software, the patents.txt file on your CD, or

ni.com/patents.

Where to Go for Support

The National Instruments Web site is your complete resource for technical support. At

ni.com/support you have access to everything from troubleshooting and application development

self-help resources to email and phone assistance from NI Application Engineers.

A Declaration of Conformity (DoC) is our claim of compliance with the Council of the European

Communities using the manufacturer’s declaration of conformity. This system affords the user

protection for electronic compatibility (EMC) and product safety. You can obtain the DoC for your

product by visiting ni.com/certification. If your product supports calibration, you can obtain

the calibration certificate for your product at ni.com/calibration.

National Instruments corporate headquarters is located at 11500 North Mopac Expressway, Austin,

Texas, 78759-3504. National Instruments also has offices located around the world to help address your

support needs. For telephone support in the United States, create your service request at

ni.com/support and follow the calling instructions or dial 512 795 8248. For telephone support

outside the United States, contact your local branch office:

Australia 1800 300 800, Austria 43 662 457990-0, Belgium 32 (0) 2 757 0020,

Brazil 55 11 3262 3599, Canada 800 433 3488, China 86 21 5050 9800,

Czech Republic 420 224 235 774, Denmark 45 45 76 26 00, Finland 358 (0) 9 725 72511,

France 01 57 66 24 24, Germany 49 89 7413130, India 91 80 41190000, Israel 972 3 6393737,

Italy 39 02 41309277, Japan 0120-527196, Korea 82 02 3451 3400, Lebanon 961 (0) 1 33 28 28,

Malaysia 1800 887710, Mexico 01 800 010 0793, Netherlands 31 (0) 348 433 466,

New Zealand 0800 553 322, Norway 47 (0) 66 90 76 60, Poland 48 22 3390150,

Portugal 351 210 311 210, Russia 7 495 783 6851, Singapore 1800 226 5886,

Slovenia 386 3 425 42 00, South Africa 27 0 11 805 8197, Spain 34 91 640 0085,

Sweden 46 (0) 8 587 895 00, Switzerland 41 56 2005151, Taiwan 886 02 2377 2222,

Thailand 662 278 6777, Turkey 90 212 279 3031, United Kingdom 44 (0) 1635 523545

Table des matières

Autres manuels National Instruments Matériel informatique

National Instruments

National Instruments MXI-2 Manuel utilisateur

National Instruments

National Instruments PXI-8335 Manuel utilisateur

National Instruments

National Instruments PCMCIA-FBUS/2 Manuel utilisateur

National Instruments

National Instruments GPIB-LPT Manuel utilisateur

National Instruments

National Instruments NI-9260 Manuel utilisateur

National Instruments

National Instruments NI 54 Series Manuel

National Instruments

National Instruments PCMCIA-232 Manuel utilisateur

National Instruments

National Instruments NI 9403 Manuel utilisateur

National Instruments

National Instruments USB-6211 OEM Manuel utilisateur

National Instruments

National Instruments DAQPad-6020E Manuel utilisateur

National Instruments

National Instruments PXIe-4468 Manuel

National Instruments

National Instruments PXI Express PXIe-1085 Series Manuel utilisateur

National Instruments

National Instruments CPCI-GPIB Manuel utilisateur

National Instruments

National Instruments NI PXI-8221 Manuel utilisateur

National Instruments

National Instruments GPIB-PCIIB Manuel utilisateur

National Instruments

National Instruments IMAQTM Manuel utilisateur

National Instruments

National Instruments PCI-1407 Instruction manuelle

National Instruments

National Instruments MXIbus VME-AT2000 Manuel utilisateur

National Instruments

National Instruments GPIB-PCII Manuel utilisateur

National Instruments

National Instruments NI-488.2M Manuel utilisateur

National Instruments

National Instruments NI 9213 Manuel utilisateur

National Instruments

National Instruments R Series Manuel utilisateur

National Instruments

National Instruments USB-7856 Manuel utilisateur

National Instruments

National Instruments 800 Series Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

Advantech

Advantech ASMB-935 Series Manuel utilisateur