MSI 648M-IL Manuel utilisateur
1-1
Getting Started
Chapter 1. Getting
Started
Getting Started
Thank you for purchasing the 648M-IL (MS-6703 v2.X)
M-ATX mainboard. The MS-6703 v2.X mainboard is based on
SiS®648 B-step & 963 chipsets for optimal system efficiency.
Designed to fit the advanced Intel®Pentium®4 processors in
the 478 pin package, the MS-6703 v2.X mainboard delivers a
high performance and professional desktop platform solution.
1-2
MS-6703 M-ATX Mainboard
Mainboard Specifications
CPU
hSupports Socket 478 for Intel Pentium 4/Celeron processors (Willamette,
Northwood and Northwood with Hyper-threading)
hSupports 400/533MHz CPU FSB
hSupports Willamette and Northwood core frequency from 1.3 GHz to 2.8 GHz
and up, Northwood with HT from 3.0 GHz and up
Chipset
hSiS®648 B-step chipset
- Supports Intel Pentium 4 processors with data transfer rate up to 533 MHz
- Supports 64-bit high performance DDR333/DDR266 memory controller
- Supports AGP 8X/4X interface
- Supports Hyper Threading technology
hSiS®963 chipset
- Supports Dual-IDE ATA 66/100/133
- Integrated audio controller with AC97 interface
- Low pin count interface for SIO
- Advanced power management and PC2001 compliance
MainMemory
hSupports two 184-pin DDR DIMMs
hSupports up to 2GB PC2700/2100/1600 DDR SDRAMs
hSupports 2.5v DDR SDRAM
Slots
hOne AGP (Accelerated Graphics Port) 4x/8x slot.
hThree 32-bit PCI bus slots (support 3.3v/5v PCI bus interface)
On-BoardIDE
hDual-IDE controller integrated in SiS 963 chipset
hSupports PIO, Bus Master and Ultra DMA133/100/66/33 operation modes
hCan connect up to four IDE devices
On-Board Peripherals
hOn-Board Peripherals include:
- 1 floppy port supports 2 FDDs with 360K, 720K, 1.2M, 1.44M and
2.88Mbytes
1-3
Getting Started
- 2 serial ports
- 1 parallel port
- 1 IrDA connector
- 3 vertical audio ports
- 6 USB ports (2 front and 4 rear)
- 1 RJ-45 Lan Jack (optional)
IEEE1394
hRealtek RTL8801B (can support up to 2 ports)
Audio
hRealtek ALC650 6-channel audio codec
LAN(optional)
hRealtek 8201B MII PHY
BIOS
hThe mainboard BIOS provides “Plug & Play” BIOS which detects the pe-
ripheral devices and expansion cards of the board automatically.
hThe mainboard provides a Desktop Management Interface (DMI) function
which records your mainboard specifications.
Dimension
hM-ATX Form Factor: 9.6” x 9.6”
Mounting
h6 mounting holes
Others
hSuspend to RAM/Disk (S3/S4)
hPC2001 compliant
hSupports WOL (optional)
1-4
MS-6703 M-ATX Mainboard
Mainboard Layout
MS-6703 v2.X M-ATX Mainboard
BATT
+
SiS
963
SiS
648
B-step
DIMM1
DIMM2
JUSB1
JAUD2
JFP1
ATX
PowerSupply
SYSFAN1
CPUFAN1
JBAT1
BIOS
PCI Slot 3
PCI Slot 2
PCI Slot 1
IDE1
IDE2
To p : P ar a l l e l P or t
Bottom:
COM A
COM B
Top : mouse
Bottom: keyboard
Top: LAN Jack
Bottom: USB
ports
T: 1394 port
B: USB ports
JCD1
Codec
Winbond
W83697HF
RTL
8801B
RTL
8201BL
JAUX1
J1394_1
JPW1
FDD1
AGP Slot
T:
Line-Out
B:Mic
Line-In
M:
CNR
JSPD2
2-1
Hardware Setup
Chapter 2. Hardware
Setup
This chapter tells you how to install the CPU, memory
modules, and expansion cards, as well as how to setup the jump-
ers on the mainboard. Also, it provides the instructions on con-
necting the peripheral devices, such as the mouse, keyboard,
etc.
While doing the installation, be careful in holding the com-
ponents and follow the installation procedures.
Hardware Setup
2-2
MS-6703 M-ATX Mainboard
Quick Components Guide
J1394_1, p.2-24
JPW1, p.2-9 CPU, p.2-3
Back Panel
I/O, p.2-10
CPUFAN1, p.2-17
FDD1, p.2-15
JUSB1, p.2-19
IDE1/2, p.2-16
JCD1, p.2-23
JAUX1, p.2-23
AGP Slot, p.2-27
PCI Slots, p.2-27
DDR DIMMs,
p.2-7
CONN1, p.2-9
JBAT1, p.2-26JAUD2, p.2-18
JFP1, p.2-22
SYSFAN1, p.2-17
JSPD2, p.2-20
CNR Slot, p.2-27
2-3
Hardware Setup
Central Processing Unit: CPU
CPU Core Speed Derivation Procedure
CPU Clock multiplied by Core/Bus ratio equals the CPU core speed.
For example:
If CPU Clock = 100MHz
Core/Bus ratio = 14
then CPU core speed = Host Clock x Core/Bus ratio
= 100MHz x 14
= 1.4 GHz
The mainboard supports Intel®Pentium®4 processor in the 478 pin
package. The mainboard uses a CPU socket called PGA478 for easy CPU
installation. When you are installing the CPU, make sure the CPU has a
heat sink and a cooling fan attached on the top to prevent overheating. If
you do not find the heat sink and cooling fan, contact your dealer to purchase
and install them before turning on the computer.
MSI Reminds You...
Overheating
Overheating will seriously damage the CPU and system, al-
ways make sure the cooling fan can work properly to protect
the CPU from overheating.
Replacing the CPU
While replacing the CPU, always turn off the ATX power sup-
ply or unplug the power supply’s power cord from grounded
outlet first to ensure the safety of CPU.
Overclocking
This motherboard is designed to support overclocking.
However, please make sure your components are able to toler-
ate such abnormal setting, while doing overclocking. Any at-
tempt to operate beyond product specifications is not
recommended. We do not guarantee the damages or risks
caused by inadequate operation or beyond product
specifications.
2-4
MS-6703 M-ATX Mainboard
1. Please turn off the power and
unplug the power cord before
installing the CPU.
2. Pull the lever sideways away
from the socket. Make sure
to raise the lever up to a 90-
degree angle.
3. Look for the cut edge. The cut
edge should point towards the
lever pivot. The CPU can only
fit in the correct orientation.
4. If the CPU is correctly
installed, the pins should be
completely embedded into the
socket and can not be seen.
Please note that any violation
of the correct installation
procedures may cause
permanent damages to your
mainboard.
5. Press the CPU down firmly
into the socket and close the
lever. As the CPU is likely to
move while the lever is being
closed, always close the lever
with your fingers pressing
tightly on top of the CPU to
make sure the CPU is
properly and completely
embedded into the socket.
CPU Installation Procedures for Socket 478
Open Lever
Sliding
Plate
Dot / Cut edge
Close
Lever
Press down
the CPU
90 degree
Dot / Cut edge
Correct CPU placement
Dot / Cut edge Incorrect CPU placement
X
O
2-5
Hardware Setup
Installing the CPU Fan
As processor technology pushes to faster speeds and higher performance,
thermal management becomes increasingly important. To dissipate heat, you
need to attach the CPU cooling fan and heatsink on top of the CPU. Follow
the instructions below to install the Heatsink/Fan:
2. Position the heatsink onto the reten-
tion mechanism.
1. Locate the CPU and its retention
mechanism on the motherboard.
3. Mount the fan on top of the heatsink.
Press down the fan until its four clips
get wedged in the holes of the reten-
tion mechanism.
4. Press the two levers down to fasten
the fan. Each lever can be pressed
down in only ONE direction.
retention mechanism
levers
2-6
MS-6703 M-ATX Mainboard
5. Connect the fan power cable from the mounted fan to the 3-pin fan power connector
on the board.
fan power cable
NOTES
Table des matières
Autres manuels MSI Carte mère
MSI
MSI MS-6507E Manuel utilisateur
MSI
MSI Z270 PC MATE Mode d’emploi
MSI
MSI MAG B550M MORTAR WIFI Manuel utilisateur
MSI
MSI B75MA-P45 series Manuel utilisateur
MSI
MSI 945GCM5 Series Manuel utilisateur
MSI
MSI MS-7357 (V1.X) Manuel utilisateur
MSI
MSI Z87 XPOWER Manuel utilisateur
MSI
MSI MS-7516 Manuel utilisateur
MSI
MSI K8NGM-V Series Manuel utilisateur
MSI
MSI X299 RAIDER Manuel utilisateur
MSI
MSI MS-7513 Manuel utilisateur
MSI
MSI B360M PRO-VD Manuel utilisateur
MSI
MSI Z490 -S01 Manuel utilisateur
MSI
MSI MS-9125 Manuel utilisateur
MSI
MSI C236A WORKSTATION Manuel utilisateur
MSI
MSI MS-7522 Manuel utilisateur
MSI
MSI MEG B550 UNIFY Manuel utilisateur
MSI
MSI B250M BAZOOKA PLUS Manuel utilisateur
MSI
MSI MS 7005 - 651M-L Motherboard - Micro ATX Manuel utilisateur
MSI
MSI MAG Series Manuel utilisateur
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
