Moxa Technologies ETHERDEVICE EDS-308 Manuel

Moxa EtherDevice Switch

EDS-308/309

Hardware Installation Guide

Eighth Edition, September 2010

Reproduction without permission is prohibited.

Fl.4, No.135, Lane 235, Pao-Chiao Rd. Shing Tien City, Taipei, Taiwan,

R.O.C.

TEL: +886-2-8919-1230

P/N: 1802003083010

- 2 -

Overview

Moxa EtherDevice™ EDS-308/309 Series, which consists of 9-,and 8-port

smart Ethernet switches, provides an economical solution for your Ethernet

connections. As an added bonus, the built-in smart alarm function helps system

maintainers monitor the health of your Ethernet network.

EDS-308/309 switches have a wide operating temperature range of -40 to 75°C,

and are designed to withstand a high degree of vibration and shock. The rugged

hardware design makes EDS-308/309 Series perfect for ensuring that your

Ethernet equipment can withstand critical industrial applications, and complies

with FCC and CE Standards.

NOTE Throughout this Hardware Installation Guide, we use EDS as an

abbreviation for Moxa EtherDevice Switch:

EDS = Moxa EtherDevice Switch

Package Checklist

Moxa EDS-308/309 is shipped with the following items. If any of these items

is missing or damaged, please contact your customer service representative for

assistance.

yMoxa EtherDevice™ Switch

yHardware Installation Guide

yMoxa Product Warranty booklet

yProtective caps for unused ports

Features

High Performance Network Switching Technology

y10/100BaseT(X) (RJ45), 100BaseFX (SC/ST-type, Multi/Single mode)

yIEEE802.3/802.3u/802.3x

yStore and Forward switching process type, with 1024 address entries

y10/100M, Full/Half-Duplex, MDI/MDIX auto-sensing

Industrial Grade Reliablity

yPower failure, port break alarm by relay output

yRedundant dual DC power inputs

Rugged Design

yOperating temperature range from 0 to 60ºC, or extended operating

temperature from -40 to 75ºC for “-T” models

yIP30, rugged high-strength case

yDIN-rail or panel mounting ability

WARNING

The power for this product is intended to be supplied by a Listed

Power Supply, with output marked LPS, and rated to deliver 12 to

48 VDC at a maximum of 0.6A.

The DC jack should be used with an LPS unit that is rated to

deliver 12 to 48 VDC at a minimum of 1.1A. The product should

not be disassembled by operators or service people.

- 3 -

EDS-308 Panel Layout

EDS-308

Front Panel View

V1 V2 INPUTS: 24 VDC

PWR2

V2+

V2-

V1-

V1+

PID

PORT ALARM

FAULT

PWR1

Top Panel View

Rear Panel View

1. Grounding screw

2. Terminal block for power inputs

PWR1/PWR2 and relay output

3. Heat dissipation orifices

4. DIP switches

5. Power input PWR1 LED

6. Power input PWR2 LED

7. Fault LED

8. 10/100BaseT(X) Port

9. TP port’s 100 Mbps LED

10. TP port’s 10 Mbps LED

11. Model Name

12. Screw holes for wall mounting kit

13. DIN-Rail Kit

- 4 -

EDS-308 Panel Layout (SC-type)

EDS-308-MM-SC

Front Panel View

EDS-308-M-SC

Front Panel View

V1 V2 INPUTS: 24 VDC

PWR2

V2+

V2-

V1-

V1+

12345

ON DIP

PORT ALARM

FAULT

PWR1

Top Panel View

Rear Panel View

NOTE: The appearance of EDS-308-S-SC

is identical to EDS-308-M-SC, and the

appearance of EDS-308-SS-SC is identical

to EDS-308-MM-SC.

1. Grounding screw

2. Terminal block for power inputs

PWR1/PWR2 and relay output

3. Heat dissipation orifices

4. DIP switches

5. Power input PWR1 LED

6. Power input PWR2 LED

7. Fault LED

8. 10/100BaseT(X) Port

9. TP port’s 100 Mbps LED

10. TP port’s 10 Mbps LED

11. Model Name

12. 100BaseFX Port

13. FX port’s 100 Mbps LED

14. Screw holes for wall mounting kit

15. DIN-Rail Kit

- 5 -

EDS-309 Panel Layout (SC-type)

EDS-309-3M-SC

Front Panel View

V1 V2 INPUTS: 24 VDC

PWR2

V2+

V2-

V1-

V1+

PORT ALARM

FAULT

PWR1

Top Panel View

Rear Panel View

1. Grounding screw

2. Terminal block for power inputs

PWR1/PWR2 and relay output

3. Heat dissipation orifices

4. DIP switches

5. Power input PWR1 LED

6. Power input PWR2 LED

7. Fault LED

8. 10/100BaseT(X) Port

9. TP port’s 100 Mbps LED

10. TP port’s 10 Mbps LED

11. Model Name

12. 100BaseFX Port

13. Screw holes for wall mounting kit

14. DIN-Rail Kit

15. 100 Mbps LED for FX port 7

16. 100 Mbps LED for FX port 8

17. 100 Mbps LED for FX port 9

- 6 -

EDS-308/309 Panel Layout (ST-type)

EDS-308-MM-ST

Front Panel View

EDS-309-3M-ST

Front Panel View

V1 V2 INPUTS: 24 VDC

PWR2

V2+

V2-

V1-

V1+

12345

ON DIP

PORT ALARM

FAULT

PWR1

Top Panel View

Rear Panel View

1. Grounding screw

2. Terminal block for power input

PWR1/PWR2 and relay output

3. Heat dissipation orifices

4. DIP switches

5. Power input PWR1 LED

6. Power input PWR2 LED

7. Fault LED

8. 10/100BaseT(X) Port

9. TP port’s 100 Mbps LED

10. TP port’s 10 Mbps LED

11. Model Name

12. 100BaseFX Port

13. 100 Mbps LEDfor FX port

14. Screw hole for wall mounting kit

15. DIN-Rail Kit

16. 100 Mbps LED for FX port 7

17. 100 Mbps LED for FX port 8

18. 100 Mbps LED for FX port 9

- 7 -

Mounting Dimensions (unit = mm)

Rear View

Side View Front View

DlN-Rail Kit

DlN-Rail

105.00

9.00 19.80

00.53

30.00

00.531

13.10 25.40

15.10

53.60

00.531

17.5273.9377.6451.32

13 18 13

02.72 03.84

Wall Mounting Kit

3.5

13.9 18.2

13.9

7.75 30.50 7.75

08.6650.75

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should already be fixed to the back

panel of EDS-308/309 when you take it out of the box. If you need to reattach

the DIN-Rail attachment plate, make sure the stiff metal spring is situated

towards the top, as shown in the figures below.

STEP 1:

Insert the top of the DIN-Rail into the

slot just below the stiff metal spring.

STEP 2:

The DIN-Rail attachment unit will

snap into place as shown below.

metal

spring

DIN-Rail

metal

spring

DIN-Rail

To remove Moxa EtherDevice Switch from the DIN-Rail, simply reverse Steps

1 and 2 above.

- 8 -

Wall Mounting (optional)

For some applications, you will find it convenient to mount EDS-308/309 on

the wall, as illustrated below.

STEP 1:

Remove the aluminum

DIN-Rail attachment plate from

EDS-308/309’s rear panel, and

then attach the wall mount

lates, as shown in the diagram

below.

⇒

top

plate

bottom

plate

STEP 2:

Mounting EDS-308/309 on the wall requires 4 screws. Use

the switch, with wall mount plates attached, as a guide to

mark the correct locations of the 4 screws. The heads of

the screws should be less than 6.0 mm in diameter, and the

shafts should be less than 3.5 mm in diameter, as shown in

the figure at the right.

6.0 mm

3.5 mm

NOTE Before tightening screws into the wall, make sure the screw head and

shank size are suitable by inserting the screw into one of the keyhole-

shaped apertures of the Wall Mounting Plates.

Do not screw the screws in all the way—leave about 2 mm to allow room for

sliding the wall mount panel between the wall and the screws.

STEP 3:

Once the screws are fixed in the

wall, insert the four screw heads

through the large parts of the

keyhole-shaped apertures, and then

slide EDS-308/309 downwards, as

indicated. Tighten the four screws

for added stability.

⇒

II 3G

ATEX Information

1. Certificate number DEMKO 08 ATEX 0717913X

2. Ambient range: -40°C ≤Tamb ≤+75°C

3. Certification String: EX nC nL IIC T4

4. Applicable standards: EN60079-0: 2006, EN60079-15:2005

5. The condition of safe usage:

a. The Ethernet Communication Devices are to be mounted in an IP54

enclosure and used in an area of not more than pollution degree 2 as

defined by IEC60664-1.

b. A 4mm² conductor must be used when connection to the external

grounding screw is utilized. Conductors suitable for use in an ambient

temperature of 93°C must be used for the Power Supply Terminal.

c. Provisions shall be made to prevent the rated voltage being exceeded by

the transient disturbances of more than 40%.

- 9 -

Wiring Requirements

WARNING

Do not disconnect modules or wires unless the power supply has

been switched off or the area is known to be non-hazardous. The

devices may only be connected to the supply voltage shown on

the type plate.

The devices are designed for operation with a Safety Extra-Low

Voltage. Thus, they may only be connected to the supply voltage

connections and to the signal contact with the Safety Extra-Low

Voltages (SELV) in compliance with IEC950/ EN60950/

VDE0805.

WARNING

Substitution of components may impair suitability for Class I,

Division 2, and Zone 2. These devices must be supplied by an

SELV source as defined in Low Voltage Directive 73/23/EEC

and 93/68/EEC.

WARNING

This unit is a built-in type. When the unit is installed in another

iece of equipment, the equipment enclosing the unit must

comply with fire enclosure regulation IEC 60950/EN60950 (or

similar regulation).

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa EtherDevice Switch.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

You should also pay attention to the following items:

yUse separate paths to route wiring for power and devices. If power wiring

and device wiring paths must cross, make sure the wires are perpendicular

at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring in

the same wire conduit. To avoid interference, wires with different signal

characteristics should be routed separately.

yYou can use the type of signal transmitted through a wire to determine

which wires should be kept separate. The rule of thumb is that wiring that

shares similar electrical characteristics can be bundled together.

yKeep input wiring and output wiring separated.

yIt is strongly advised that you label wiring to all devices in the system when

necessary.

- 10 -

Grounding Moxa EtherDevice Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well-grounded

mounting surface, such as a metal panel.

Wiring the Alarm Contact

The Alarm Contact consists of the two middle contacts of the terminal block on

EDS’s top panel. You may refer to the next section for detailed instructions on

how to connect the wires to the terminal block connector, and how to attach the

terminal block connector to the terminal block receptor. In this section, we

explain the meaning of the two contacts used to connect the Alarm Contact.

FAULT

Top View

Front View

FAULT: The two middle contacts of the 6-contact

terminal block connector are used to detect both

power faults and port faults. The two wires

attached to the Fault contacts form an open circuit

when:

1. The EDS has lost power from one of the DC

power inputs.

2. One of the ports for which the corresponding

PORT ALARM DIP Switch is set to ON is not

properly connected.

If neither of these two conditions is satisfied, the

Fault circuit will be closed.

Wiring the Redundant Power Inputs

The top two contacts and the bottom two contacts of the 6-contact terminal

block connector on the EDS’s top panel are used for the EDS’s two DC inputs.

Top and front views of one of the terminal block connectors are shown here.

Top View

Front View

STEP 1: Insert the negative/positive DC wires

into the V-/V+ terminals.

STEP 2: To keep the DC wires from pulling

loose, use a small flat-blade screwdriver to tighten

the wire-clamp screws on the front of the terminal

block connector.

STEP 3: Insert the plastic terminal block

connector prongs into the terminal block receptor,

which is located on the EDS’s top panel.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Moxa Technologies Routeur réseau

Moxa Technologies

Moxa Technologies PowerTrans PT-7728 Manuel

Moxa Technologies

Moxa Technologies EDS-518E Manuel utilisateur

Moxa Technologies

Moxa Technologies TN-5916 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NAT-102 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies MAR-2000 Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-G308 Manuel

Moxa Technologies

Moxa Technologies EDR-810 Series Manuel

Moxa Technologies

Moxa Technologies WDR-3124A Manuel utilisateur

Moxa Technologies

Moxa Technologies ToughNet TN-5516 Series Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDR-G902-T Manuel utilisateur

Moxa Technologies

Moxa Technologies SDS-3008 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies E Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-408A Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDS-G205A-4PoE Manuel

Moxa Technologies

Moxa Technologies PT-7528 Manuel utilisateur

Moxa Technologies

Moxa Technologies AirWorks AWK-1137C-EU Manuel utilisateur

Moxa Technologies

Moxa Technologies UC-8112-LX-STK Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort IA5150 series Manuel utilisateur

Moxa Technologies

Moxa Technologies SR3000 Manuel utilisateur

Moxa Technologies

Moxa Technologies ioLogik E2200Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Manuel utilisateur

Moxa Technologies

Moxa Technologies TSN-G5000 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-505A Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EDR-G9010 Series Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité