Moxa Technologies NAT-102 Series Manuel utilisateur

P/N: 1802001024010

*1802001024010*

NAT-102 Series

Quick Installation Guide

Moxa Industrial NAT Device

Version 1.0, November 2021

Technical Support Contact Information

www.moxa.com/support



- 2 -

Package Checklist

The NAT-102 Series, which is a NAT device, is shipped with the items

listed below. If any of these items are missing or damaged, please

contact your customer service representative for assistance.

•1 Industrial NAT device

•1 USB-C-to-DB9 cable

•Quick installation guide (printed)

•Protective caps for unused ports

•Warranty card

Features

•Complete NAT functionality for speeding up Industry 4.0

connectivity

•Enhanced security through automatic network access control with

auto whitelisting of locally connected devices

•Ultra-compact size for cabinet installation

•Rugged hardware that supports a -40 to 75°C operating

temperature (T model)

- 3 -

Panel Views of NAT-102 Series

Front Panel

Top Panel

Front Panel:

1. POWER LED indicator

2. STATE LED indicator

3. LEARNING LED indicator

4. LOCKDOWN LED indicator

5. 10/100 Mbps copper external

port

6. 10/100 Mbps copper internal

port

Top Panel:

1. Grounding screw

2. Terminal block with latch for

power input

3. Type-C serial console port

4. Reset button

- 4 -

Rear Panel

Rear Panel:

1. DIN-rail mounting kit

Mounting Dimensions

DIN-rail Mounting

In the package, the metal DIN-rail mounting kit is fixed to the back

panel of the NAT-102 Series. Mount the NAT-102 Series on a corrosion-

free mounting rail that adheres to the EN 60715 standard.

- 5 -

Suggested Installation Method

STEP 1:

Insert the upper lip

of the DIN-rail

kit into the mounting rail.

STEP 2

Press the

NAT-102 Series towards

the mounting rail until it snaps into

place.

Suggested Removal Method

STEP 1:

Pull down the latch on the DIN

-rail

kit with a screwdriver.

STEPS 2 & 3

Slightly pull the

NAT-102 Series

forward and lift

it up to remove it

from the mounting rail.

Wall Mounting

For some applications, you will find it convenient to mount the NAT-102

Series on the wall, as shown in the following illustrations.

STEP 1: Remove the aluminum DIN-rail attachment plate from the rear

panel of the NAT-102 Series, and then attach the wall mount plates

with three M3 screws.

- 6 -

STEP 2: Mounting the NAT-102 Series on the wall requires two M3

screws. Use the NAT-102 Series with the wall mount plates attached as

a guide to mark the correct location of the two screws.

Wiring Requirements

WARNING

Do not disconnect modules or wires unless power has been

switched off or the area is known to be non

-hazardous. The

devices may only be connected to the supply voltage shown on

the type plate.

ATTENTION

This unit is a built

-in type. When the unit is installed in another

piece of equipment, the equipment

enclosing the unit must

comply with fire enclosure regulation IEC 60950

-1/EN60950-1

(or similar regulation).

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your

NAT-102 Series.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring

could overheat, causing serious damage to your equipment.

Please read and follow these guidelines:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power

wiring through the same wire conduit. To avoid interference, wires

with different signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb

is that wiring sharing similar electrical characteristics can be

bundled together.

•You should separate input wiring from output wiring.

•We advise that you label the wiring to all devices in the system.

•This product is intended for installation in Restricted Access

Location.

WARNING

Hot Surface. Do not touch.

- 7 -

Grounding the NAT-102 Series

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from

the ground screw (M4 type) to the grounding surface prior to

connecting devices.

The grounding wire must be connected to the grounding screw using a

cable lug. The grounding cable must have a cross-sectional area that is

the same or larger than the 0.08 mm² (28 AWG) to 1.31 mm² (16

AWG) terminal input conductor wire.

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface such as a metal panel.

Wiring the Power Inputs

The NAT-102 Series has one power input. The top and side views of the

terminal block connector are shown below.

Top View

Right View

STEP 1:

Use a small flat

blade screwdriver

to press a wire locker.

STEP 2:

Insert a positive/negative DC wire

into the V+/V

terminals

respectively.

STEP 3:

Release the wire locker and check

whether the wire is fixed.

The

nput terminal block (J1)

should be installed using 16

AWG wires with 8

9 mm of the

conductor insulation stripped.

The power cord adapter should be connected to a socket outlet with an

earthing connection. The power cord and adapter must comply with

Class II construction.

This product is intended to be supplied by a UL Listed Power Adapter or

DC power source marked ‘L.P.S’ or ‘Limited Power Source’, rated 12 to

48 VDC, 0.196 A (min.), and Tma 75°C (min.). If you require further

assistance, please contact your Moxa representative.

Communication Connections

Each NAT-102 Series has two types of communication ports:

•1 Type-C console port (RS-232 interface, baudrate: 115200, 8-N-1)

- 8 -

•2 10/100BaseT(X) Ethernet ports

TYPE-C Console Port Connection

The NAT-102 Series provides one TYBP-C console port located on the

top panel. Connect the industrial secure router to a PC COM port using

the Type-C-to-DB9 connection cable, and then launch a console

terminal software, e.g. Moxa PComm Terminal Emulator, to access the

NAT-102 Series’ console configuration utility.

TYPE-C-to-DB9 Cable Wiring

BROWN

GREEN

RED

BLUE

ORANGE

PURPLE

PIN Definition

Description

TXD

A5, B5

RXD

A6, B6

GND

A7, B7

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on the NAT-102 Series front panel

are used to connect to Ethernet-enabled devices. Most users will choose

to configure these ports for Auto MDI/MDI-X mode, in which case the

port’s pinouts are adjusted automatically depending on the type of

Ethernet cable used (straight-through or cross-over), and the type of

device (NIC-type or HUB/Switch-type) connected to the port. No matter

which case you are connecting, we share pinouts for both MDI (NIC-

type) ports and MDI-X (HUB/Switch-type) ports.

10/100Base T(x) RJ45 Pinouts

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Tx-

Rx+

Rx-

Signal

Rx+

Rx-

Tx+

Tx-

The Reset Button

Using a pointed object such as a straightened paperclip or toothpick,

depress the Reset button for five seconds to load the factory default

settings. When pressing down, the STATE LED will start to blink about

once per second. Continue to depress until the STATE LED begins

- 9 -

blinking more quickly, indicating that the device is resetting and you

can release.

NOTE

DO NOT power off the device when loading default settings.

LED Indicators

The front panel of the NAT-102 Series has several LED indicators. The

function of each LED is described in the following table:

LED

Color

State

Description

PWR Amber

On Power is being supplied to the power

input.

Off Power is

NOT

being supplied to the

power.

STATE Green

The system passed the self-diagnosis

test on boot-up and is ready to run.

Blinking

Device reset is in progress, blinking

once per second.

Off The system failed the self-

diagnosis test

on boot-up.

LEARN Amber Blinking

The device lockdown learning is in

progress.

Off

Learning finished.

LOCKDOW

N Green

The device lockdown whitelist is

enabled.

Off

The device lockdown whitelist is

disabled.

Specifications

Input Current

0.196 A @ 12 V

0.100 A @ 24 V

0.056 A @ 48 V

Input Voltage

12/24/48 VDC

Power Consumption

2.69 W (max.)

Operating Temperature -10 to 60°C (14 to 140°F), standard models

-40 to 75°C (-40 to 167°F), wide-temp.

models

Storage Temperature

-40 to 85°C (-40 to 185°F)

- 10 -

Standards and Certifications

WARNING

사

용자안내문

이

기기는 업무용 환경에서 사용할 목적으로 적합성 평가를 받은

기기로서

가정용

환경에서 사용하는 경우 전파간섭의 우려가 있습니다.

ATEX information

II 3 G

Ex ec IIC T4 Gc

UL 21 ATEX 2604X

Ambient Range : -40 ℃≦Tamb ≦+75 ℃(With -

T) Ambient Range : -10 ℃≦Tamb ≦+60 ℃

(Without -T) Rated Cable Temp

≧

℃

Address of the

manufacturer

No. 1111, Heping Rd., Bade Dist., Taoyuan City

334004, Taiwan

Hazardous

Location

EN IEC 60079-0:2018

EN IEC 60079-7:2015+A1:2018

Special Use Conditions

•The equipment shall only be used in an area of at least pollution

degree 2, as defined in EN IEC 60664-1.

•The equipment shall be mounted in vertical position and installed in

an enclosure that provides a minimum ingress protection of IP54 in

accordance with EN IEC 60079-0 and only accessible by use of a tool.

Table des matières

Autres manuels Moxa Technologies Routeur réseau

Moxa Technologies

Moxa Technologies TN-5916 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies SDS-3008 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies OnCell 5004-HSPA Manuel utilisateur

Moxa Technologies

Moxa Technologies SDS-3008 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Manuel

Moxa Technologies

Moxa Technologies ToughNet Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-305-M12 Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDR-G902 Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDS-508 Manuel

Moxa Technologies

Moxa Technologies EDR-810 Series Manuel

Moxa Technologies

Moxa Technologies MAR-2000 Manuel utilisateur

Moxa Technologies

Moxa Technologies TSN-G5000 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-G308 Manuel

Moxa Technologies

Moxa Technologies ioLogik E1200 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies PowerTrans PT-7728 Manuel

Moxa Technologies

Moxa Technologies TN-4900 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies Managed Ethernet Switch/Extender Manuel utilisateur

Moxa Technologies

Moxa Technologies AirWorks AWK-1137C-EU Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-518E Manuel utilisateur

Moxa Technologies

Moxa Technologies EDR-8010 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-408A Manuel

Moxa Technologies

Moxa Technologies AWK-4121 Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort IA5150 series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-G205A-4PoE Manuel

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité