Moxa Technologies EDS-408A Manuel

Moxa EtherDevice™ Switch

EDS-408A Hardware Installation Guide

First Edition, November 2008

Reproduction without permission is prohibited.

Fl.4, No.135, Lane 235, Pao-Chiao Rd. Shing Tien City, Taipei, Taiwan,

R.O.C.

TEL: +886-2-8919-1230

P/N: 1802004000020

—1 —

Overview

The Moxa EtherDevice™ EDS-408A series are a cost-effective solution for

your Ethernet connections. In addition, the built-in smart alarm function helps

system maintainers monitor the health of your Ethernet network.

Package Checklist

The Moxa EDS-408A is shipped with the following items. If any of these items

is missing or damaged, please contact your customer service representative for

assistance.

y1 Moxa EtherDevice Switch

yHardware Installation Guide

yCD-ROM with User’s Manual and Windows Utility

yWarranty Statement

yRJ45 to DB9 Console port cable

yProtective caps for unused ports

yPanel Mounting Kit (optional—must order separately)

Features

¾Advanced Industrial Networking Capability

yRedundant Self-Healing Ethernet Ring Capability

yPort-Based VLAN to ease network planning

yQoS—IEEE802.1p and TOS/DiffServ to increase determinism

ySNMP V1/V2c/V3 and RMON for high security network management

¾Designed for IndustrialApplications

yBandwidth management to prevent unpredictable network status

yPort mirroring for online debugging

yAutomatic warning by exception through email, relay output

yAutomatic recovery of IP addresses from connected devices

yLine-swap fast recovery (patent pending)

yRedundant, dual DC power inputs

y-40 to 75°C operating temperature range (for -T models)

yIP30, rugged high-strength case

yDIN-Rail or panel mounting ability

¾Useful Utilities and Remote Configuration Facility

yConfigurable by Web browser, Telnet/Serial console, Windows utility,

and SNMP

ySend ping commands to identify network segment integrity

—2 —

Panel Layout of EDS-408A (Standard)

EDS-408A

Front Panel View

V1, V2 INPUTS: 12-45 VDC

V2+

V2-

V1-

V1+

RS-232 CONSOLE

------

MASTER

COUPLER

TURBO

RING

ONOFF

PWR2

RELAY

PWR1

Top Panel View

Rear Panel View

4321

1. Grounding screw

2. Terminal block for power

input PWR1/PWR2 and relay

output

3. Heat dissipation orifices

4. Console port

5. DIP switches

6. Power input PWR1 LED

7. Power input PWR2 LED

8. Fault LED

9. Master LED

10. Coupler LED

11. Turbo Ring logo

12. TP port’s 100 Mbps LED

13. TP port’s 10 Mbps LED

14. Model Name

15. 10/100BaseT(X) ports

16. Screw hole for wall mounting

kit

17. DIN-Rail kit

—3 —

Panel Layout of EDS-408A-MM

(SC & ST-type)

EDS-408A-MM-SC

Front Panel View

EDS-408A-MM-ST

Front Panel View

V1, V2 INPUTS: 12-45 VDC

V2+

V2-

V1-

V1+

RS-232 CONSOLE

------

MASTER

COUPLER

TURBO

RING

ONOFF

PWR2

RELAY

PWR1

Top Panel View

Rear Panel View

4321

NOTE:

The appearance of EDS-408A-SS-SC is

identical to that of EDS-408A-MM-SC.

1. Grounding screw

2. Terminal block for power input

PWR1/PWR2 and relay output

3. Heat dissipation orifices

4. Console port

5. DIP switches

6. Power input PWR1 LED

7. Power input PWR2 LED

8. Fault LED

9. Master LED

10. Coupler LED

11. Turbo Ring logo

12. TP port’s 100 Mbps LED

13. TP port’s 10 Mbps LED

14. Model Name

15. 10/100BaseT(X) ports

16. 100BaseFX ports

17. FX port’s 100 Mbps LEDs

18. Screw hole for wall mounting kit

19. DIN-Rail kit

—4 —

Panel Layout of EDS-408A-3M

(SC & ST-type)

EDS-408A-3M-SC

Front Panel View Front Panel View

910

10 15

EDS-408A-3M-ST

11 11

RS-232 CONSOLE

------

MASTER

COUPLER

TURBO

RING

ONOFF

Top Panel View

Rear Panel View

NOTE: The appearance of

EDS-408A-3S-SC,

EDS-408A-1M2S-SC and

EDS-408A-2M1S-SC are identical to

that of EDS-408A-3M-SC.

1. Grounding screw

2. Terminal block for power input

PWR1/PWR2 and relay output

3. Console port

4. DIP switches

5. Heat dissipation orifices

6. Power input PWR1 LED

7. Power input PWR2 LED

8. Fault LED

9. Master LED

10. Coupler LED

11. 10/100BaseT(X) ports

12. TP port’s 100 Mbps LED

13. TP port’s 10 Mbps LED

14. 100BaseFX ports

15. 1 FX port’s 100Mbps LEDs

100M-M: multi mode FX port

100M-S: single mode FX port

16. Model Name

17. Screw hole for wall mounting kit

18. DIN-Rail kit

—5 —

Mounting Dimensions (unit = mm)

Rear View

Side View Front View

Wall Mounting Kit

DlN-Rail Kit

DlN-Rail

105.00

113.8

7.75 30.50 7.75

9.00 32.30

35.00 134 9

30.00

135.00

25.29

13 18 13

27.20

48.30

23.56 46.61 39.54

135.00

13.1015.10 25.40

3.5

66.80

57.05

13.9 18.2 13.9

45.8

52.9

105 28

—6 —

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should already be fixed to the back

panel of the EDS-408A when you take it out of the box. If you need to reattach

the DIN-Rail attachment plate, make sure the stiff metal spring is situated

towards the top, as shown in the following figures.

STEP 1:

Insert the top of the DIN-Rail into the

slot just below the stiff metal spring.

STEP 2:

The DIN-Rail attachment unit will

snap into place as shown.

metal

spring

DIN-Rail

metal

spring

DIN-Rail

To remove the Moxa EtherDevice switch from the DIN-Rail, simply reverse

Steps 1 and 2.

Wall Mounting (optional)

For some applications, you will find it convenient to mount the EDS-408A on

the wall, as shown in the following figures.

STEP 1: Remove the

aluminum DIN-Rail

attachment plate from the

EDS-408A’s rear panel, and

then attach the wall mount

plates with M3 screws, as

shown in the diagram at the

right.

⇒

top

plate

bottom

plate

STEP 2:

Mounting the EDS-408A on the wall requires 4 screws.

Use the switch, with wall mount plates attached, as a

guide to mark the correct locations of the 4 screws. The

heads of the screws should be less than 6.0 mm in

diameter, and the shafts should be less than 3.5 mm in

diameter, as shown in the figure at the right.

6.0 mm

3.5 mm

NOTE Before tightening screws into the wall, make sure the screw head

and shank size are suitable by inserting the screw into one of the

keyhole-shaped apertures of the Wall Mounting Plates.

Do not screw the screws in completely—leave about 2 mm to allow room for

sliding the wall mount panel between the wall and the screws.

—7 —

STEP 3: Once the screws are fixed on the

wall, insert the four screw heads through

the large parts of the keyhole-shaped

apertures, and then slide the EDS-408A

downwards, as indicated. Tighten the four

screws for added stability.

II 3G

ATEX Information

1. Certificate number DEMKO 08 ATEX 0712961X

2. Ambient range (-40°C ≤Tamb ≤75°C)

3. Certification string (Ex nC nL IIC T4)

4. Standards covered ( EN60079-0:2006, EN60079-15:2005)

5. The conditions of safe usage:

yThese products must be mounted in an IP54 enclosure.

yInstall in an area of pollution degree 2 or less.

yUse a conductor wire of size 0.2 mm² or greater.

yPROVISIONS SHALL BE MADE, EXTERNAL TO THE

APPARATUS, TO PREVENT THE RATED VOLTAGE BEING

EXCEEDED BY THE TRANSIENTS DISTURBANCES OF MORE

THAN 40 %

Wiring Requirements

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa EtherDevice Switch.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

Be sure to read and follow these important guidelines:

yUse separate paths to route wiring for power and devices. If power wiring

and device wiring paths must cross, make sure the wires are perpendicular

at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

yUse the type of signal transmitted through a wire to determine which wires

should be kept separate. The rule of thumb is that wiring that shares similar

electrical characteristics can be bundled together.

yKeep input wiring and output wiring separate.

yIt is strongly advised that you label wiring to all devices in the system,

when necessary.

—8 —

Grounding the EtherDevice Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well-grounded

mounting surface, such as a metal panel.

Wiring the Relay Contact

The Relay Contact consists of the two middle contacts of the terminal block on

the EDS-408A’s top panel. Refer to the next section for detailed instructions on

how to connect the wires to the terminal block connector, and how to attach the

terminal block connector to the terminal block receptor.

In this section, we explain the meaning of the two contacts used to connect the

Alarm Contact.

Relay

FAULT: The two middle contacts of the

6-contact terminal block connector are used to

detect both power faults and port faults. The two

wires attached to the fault contacts form an open

circuit when:

1. A relay warning event is triggered.

2. The EDS-408A is the Master of this Turbo

Ring, and the Turbo Ring is broken.

3. Start-up failure.

If none of these three conditions is satisfied, the

fault circuit will remain closed.

Wiring the Redundant Power Inputs

The top two contacts and the bottom two contacts of the 6-contact terminal

block connector on the EDS-408A’s top panel are used for the EDS-408A’s

two DC inputs. Top and front views of one of the terminal block connectors are

shown in the following figures:

PWR1

V1+ V1- V2+ V2-

PWR2

STEP 1: Insert the negative/positive DC wires

into the V-/V+ terminals, respectively.

STEP 2: To keep the DC wires from pulling

loose, use a small flat-blade screwdriver to

tighten the wire-clamp screws on the front of

the terminal block connector.

STEP 3: Insert the plastic terminal block

connector prongs into the terminal block

receptor, which is located on the

EDS-405A/408A’s top panel.

—9 —

ATTENTION

Before connecting the EDS-408A to the DC power inputs, make

sure the DC power source voltage is stable.

Communication Connections

EDS-408A models have 8, 6 or 5 10/100BaseT(X) Ethernet ports, and 0 (zero),

2 or 3 100BaseFX (SC/ST-type connector) fiber ports.

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on the EDS’s front panel are used to

connect to Ethernet-enabled devices.

Next, we show pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports, and also show cable wiring diagrams for

straight-through and cross-over Ethernet cables.

MDI Port Pinouts MDI-X Port Pinouts 8-pin RJ45

Pin Signal Pin Signal

1 Tx+ 1 Rx+

2 Tx- 2 Rx-

3 Rx+ 3 Tx+

6 Rx- 6 Tx-

RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring

Straight-Through Cable

RJ45 Plug Pin 1

Switch Port

RJ45

Connector RJ45

Connecto

Tx+

Tx-

Rx+

Rx-

NIC Port

Cable Wiring

3 3

6 6

1 1

2 2

Rx+

Rx-

Tx+

Tx-

RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring

Cross-Over Cable

RJ45 Plug Pin 1

Switch Port

(NIC Port)

RJ45

Connector RJ45

Connector

Tx+

Tx-

Rx+

Rx-

(Rx+)

(Rx-)

(Tx+)

(Tx-)

(Tx+)

(Tx-)

(Rx+)

(Rx-)

Switch Port

(NIC Port)

Cable Wiring

3 1

6 2

1 3

2 6

Rx+

Rx-

Tx+

Tx-

Autres manuels pour EDS-408A

Table des matières

Autres manuels Moxa Technologies Routeur réseau

Moxa Technologies

Moxa Technologies NPort IA5150 series Manuel utilisateur

Moxa Technologies

Moxa Technologies ETHERDEVICE EDS-308 Manuel

Moxa Technologies

Moxa Technologies SDS-3008 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies AirWorks AWK-1137C-EU Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-G308 Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDR-G902-T Manuel utilisateur

Moxa Technologies

Moxa Technologies EDR-810 Series Manuel

Moxa Technologies

Moxa Technologies NSwitch Manuel utilisateur

Moxa Technologies

Moxa Technologies PT-7528 Manuel utilisateur

Moxa Technologies

Moxa Technologies PowerTrans PT-7728 Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Manuel utilisateur

Moxa Technologies

Moxa Technologies TN-4900 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EDR-G9010 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-518E Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDR-G902 Manuel

Moxa Technologies

Moxa Technologies EtherDevice Switch EDS-G205 Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Manuel utilisateur

Moxa Technologies

Moxa Technologies OnCell 5004 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies TN-5916 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies SR3000 Manuel utilisateur

Moxa Technologies

Moxa Technologies ioLogik E1210 Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-G205A-4PoE Manuel

Moxa Technologies

Moxa Technologies EDR-G9010 Series Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité