Motorola PTP 300Series Guide de référence rapide

PTP 300/500 Series

Deployment Guide

Contents

Protect Your Installation.............................................................................................................................. 2

Checklist, Site Survey and Tools................................................................................................................. 5

Bench Testing (Optional)............................................................................................................................. 6

Mast, Tower or Building Installation .......................................................................................................... 10

Installation Wiring...................................................................................................................................... 13

Cable Preparation and Installation............................................................................................................ 14

Testing and Fault Finding (Troubleshooting)............................................................................................. 17

Installation and Commissioning................................................................................................................. 20

User Information to be Recorded.............................................................................................................. 23

Registration Warranty and Ordering Information....................................................................................... 25

License Keys and Regulatory Information................................................................................................. 26

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Protect Your Installation

Attention

ElectroMagnetic Discharge (Lightning)

Protect Your Installation!

EMD (Lightning) damage is not covered under warranty.

The recommendations on this card and in the user manual, when installed correctly, give

the user the best protection from the harmful effects of EMD. However 100% protection is

neither implied or possible.

The recommended standard components for protecting installations are:

•Screened CAT 5e cable also known as Shielded CAT 5e or CAT 5e STP (Shielded Twisted

Pair)

•Surge arrestor: type PTP-LPU: 2 per link (1 Motorola Kit Part Number WB2978AA)

•Grounding stake (if no suitable grounding point can be found)

•Grounding cable: minimum size 8 AWG, preferably 6 or 4 AWG

•RJ45 screened connectors

•Andrew grounding assembly type 223158 or similar (if required by local regulations).

NOTE: If a coaxial (or other) cable is already cross-bonded to the mast or tower, the same

cross bonding points on the mast or tower must be used for the CAT 5e cable.

We recommend that the practices and procedures detailed in the Motorola manual R56

STANDARDS AND GUIDELINES FOR COMMUNICATION SITES (68P81089E50) be applied to

all new site build activities. This manual is provided on the PTP 300 or PTP 500 CD-ROM.

Lightning Protection Unit

(PTP-LPU)

Grounding Stake

Grounding Cable

(from Custome

)

Power/Ethernet

Connection

ODU

Typical Wall Installation

Copper Connection

to Network

Screened CAT 5e cable

PIDUPlus

Fitted inside building

Copper Connection to

Network

PIDU Plus

Lightning Protection Unit PTP-LPU.

Typical Mast /

Towe

Installation

Grounding Stake

ODU

Ground Connections should be

less than 0.6 meters (2 feet) long.

ll upper tower grounds should

be within 0.3 meters (1 foot) o

the ODU bracket and on the

same metal.

ODU is supplied with

1 ground cable (0.6

metres length)

PTP-LPU to ODU

Screened CAT 5e

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Protect Your Installation

Lightning Protection Zones

When the ODU is installed on a mast, tower or wall, it may be in one of two possible lightning

protection zones:

•Zone A: In this zone a direct lighting strike is possible. Do not mount the ODU in this zone.

•Zone B: In this zone, direct EMD (Lightning) effects are still possible, but mounting in this

zone significantly reduces the possibility of a direct strike. Mount the ODU in this zone.

Zone AZone A

Recommended NOT Recommended

Zone BZone B

Zone A

Finial Recommended

Zone B

The following protection requirements are mandatory:

•The ODU must be earthed

•Screened CAT 5e cable must be used

•Surge arrestor of type PTP-LPU must be installed at building entry

•There must be an earth connection at building entry

More information: PTP 300 Series User Guide

or PTP 500 Series User Guide Section: “Lightning Protection”

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Protect Your Installation

Additional Grounding Requirements for Connectorized ODU

Where the ODU is mounted outdoors and is mounted some distance from the antenna, it is

advisable to add additional grounding by utilizing Andrew assemblies (such as Andrew Type

223158):

Connectorized ODU

ntenna Cable

Antenna Cable

Grounded to Tower

Antenna Cables

Grounded to Tower

Antenna Cable Grounded

to Tower.

Antenna cables should be grounded

within 0.3 metres (1 foot) of the ODU

and Antennas

Additional Grounding Requirements for Connectorized ODU

Note: Antenna cables grounded using

an Andrew grounding assembly type

223158 or similar.

NOTE: Refer to instructions contained in the Andrew grounding kit for correct installation, or

if instructions are missing, refer to:

http://awapps.commscope.com/catalog/product_details.aspx?id=15832&tab=2

More information: PTP 300 Series User Guide

or PTP 500 Series User Guide Section: “Connectorized PTP 500 Series

Bridge”

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Checklist, Site Survey and Tools

CAUTION: Before performing an installation of a Motorola PTP 300 or PTP 500 Series

system, ensure that you have read this entire guide and taken note of any safety

information contained.

Checklist

•Check the contents of all packages against the packing list

•Check the Web site for the latest software load

List of Special Tools Required

•13mm wrench and 22 mm wrench for use with the glands

•RJ45 crimp tool (it must be the correct tool for the type of RJ45 being used)

•Personal Computer (PC) with 10, 100 or 1000 BaseT Ethernet

•Either Internet Explorer version 6 or higher, or FireFox 2.0 or higher are recommended

•Ethernet patch cables

•Motorola PTP LINKPlanner report for this link

•Crimp tool for grounding lugs (only required when installing a connectorized ODU)

More information: PTP 300 Series User Guide

or PTP 500 Series User Guide Section: “Installation”

Pre-installation: Site Survey and Link Planning

A site survey must be performed to identify all the obstructions (such as trees or buildings) in the path and

to assess the risk of interference. This information is important if you are to achieve an accurate link

feasibility assessment.

The PTP 300 and PTP 500 Series are designed to operate in Non-Line-of-Sight (NLoS) and Line-of-Sight

(LoS) environments. Link planning enables a link of known quality to be installed. This involves the

acquisition of path profile data (using Motorola’s free LINKPlanner utility). The LINKPlanner predicts data

rates and reliability over the path. It allows the user to try different antenna heights and RF power settings.

When the link is installed, the mean path loss can be checked to confirm that the predicted data rate and

link reliability is achievable. Motorola LINKPlanner is available to download from

http://www.motorola.com/ptp/support.

More information: PTP 300 Series User Guide

or PTP 500 Series User Guide Section: “Site Planning”

Pre-installation: License Keys and Regulatory Conformity

If the units have been purchased as a pair (link) then the License Keys (at the end of this guide or

printed on a separate card in the box) will show how the units have been pre-configured to work as

a link. Software, license key, unit IP address, subnet mask, gateway address, target address,

master/slave and arming state are pre-configured.

CAUTION: Check that the link is configured with the correct Region Code. If Region Code

is incorrect, then re-configure the units with Alternative License Keys before installing and

commissioning the link. Refer to “Configuration Checks” for details of how to change the

License Key.

More information: PTP 300 Series User Guide

or PTP 500 Series User Guide Section: “Radio Link Planning and

Regulations”

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Bench Testing (Optional)

It is advised that the link be configured and tested on a bench before the final installation of the

units on a pole or a mast. The following steps give details of how to connect an ODU to a PC in

order to check the configuration details, change the IP settings or modify the license key. For the

purpose of these tests, normal off-the-shelf Ethernet cables can be used.

Power Checks

Step 1: Connect the RJ45 at one end of a cable to the ODU.

Step 2: Undo the retaining screw of the PIDU Plus and hinge back the cover.

Step 3: Plug in the ODU to PIDU Plus Cable, ensuring that it snaps home.

Step 4: Put the cover back and tighten the screw.

Step 5: Plug in power lead using a cable appropriate for the installation.

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Bench Testing (Optional)

NOTE: If the power LED does not illuminate, remove the power cable and the ODU

connection from the PIDU Plus. Re-connect the power lead and check the power

LED illumination (green). If the power LED still does not light then check the power

source.

Step 6: Connect a second Ethernet cable (shown in yellow) to the “LAN” socket of the PIDU

Plus.

Step 7: 30 seconds after powering, the Ethernet LED should be observed to flash slowly 10

times. If the Ethernet LED does not illuminate (orange), then either the PIDU Plus or the

cable to the ODU may be faulty. Replace cable and/or PIDU Plus and repeat from Step 1.

Step 8: Ensure PC is set to correct IP address 169.254.1.x, where 2 < x < 254. Connect the

LAN cable to the PC (shown here in yellow).

NOTE: If this IP address is not recognised, try 10.10.10.11 (Master) and 10.10.10.10

(Slave). Some units may have been pre-configured with these IP addresses. If it is

necessary to use IP addresses 10.10.10.11 and 10.10.10.10, ensure that the PC is

configured with an IP address of 10.10.10.n, where n is any value between 2 and

254 but excluding 10 and 11, to configure these units.

Step 9: Check that the Ethernet LED is now ON. If the LED does not show any activity

when accessing web pages, refer to “Testing and Fault Finding (Troubleshooting)”.

CAUTION: Do not dress the RJ45 cables too tightly, as this may make the connections

unreliable.

More information: PTP 300 Series User Guide

or PTP 500 Series User Guide Section: “Connecting Up”

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Bench Testing (Optional)

Configuration Checks

Step 1: Use a web browser to connect to IP address http://169.254.1.1 for Slave and

http://169.254.1.2 for Master units. Select System Administration and Login (the

password is empty for new units). We recommend that you change the password by

selecting Change Password.

Step 2: If an upgrade to the software is required, select Software Upgrade and follow the

on-screen instruction. Latest software is available from our web site:

(http://motorola.motowi4solutions.com/software/#ptp)

Step 3: Check the License Key information and ensure you are using the correct Region

Code. Otherwise, select License Key and replace with the alternative key supplied and

reboot the unit.

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Bench Testing (Optional)

Step 4: Access the ‘Installation Wizard’ page. Confirm the target MAC Address,

Master/Slave choice, Symmetry, Max Transmit Power. Confirm installation configuration

and reboot.

Paired Unit

Repeat the Power Checks and Configuration Checks for the paired unit and check that the status

of the link shows UP on the ‘Status Page’.

More information: PTP 300 Series User Guide

or PTP 500 Series User Guide Section: “System Administration Pages”

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Mast, Tower or Building Installation

Hoist and Safety Loop

Use the integral safety loop for hoisting the ODU up a mast, tower or building. When the ODU is in

position, use the safety loop as a fixing point to secure a permanent lanyard from the mast, tower

or building to the ODU, as a precaution against mounting failure.

WARNING: The safety lanyard must not exceed 1m (approx 3 ft) in length. The lanyard

must be made from a material that does not degrade in an outdoor environment.

WARNING: The safety lanyard must be fixed to a separate fixing point that is not part of the

direct mounting system for the ODU.

WARNING: If the safety loop or its fixing is damaged in any way or has been exposed to a

shock loading due to a fall, replace it with a new one before undertaking any further

operations.

More information: PTP 300 Series User Guide

or PTP 500 Series User Guide Section: “Mounting the ODUs”

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Motorola Routeur réseau

Motorola

Motorola PTP 300 Series Guide de référence rapide

Motorola

Motorola VL-RISC MCF5202 Manuel utilisateur

Motorola

Motorola MR1700 Manuel utilisateur

Motorola

Motorola Wireless Broadband Platform Manuel utilisateur

Motorola

Motorola Netopia 4686-XL Manuel utilisateur

Motorola

Motorola PTP 48600 Manuel utilisateur

Motorola

Motorola PTP 300 Series Manuel utilisateur

Motorola

Motorola 68390 - Vanguard 320 Router Manuel utilisateur

Motorola

Motorola RFS6000 - Wireless RF Switch Manuel utilisateur

Motorola

Motorola CPEI 890 Manuel utilisateur

Motorola

Motorola EX-3524 Manuel utilisateur

Motorola

Motorola WR850G - Wireless Broadband Router Manuel utilisateur

Motorola

Motorola WE800G - Wireless EN Bridge Mode d'emploi

Motorola

Motorola 2247 Manuel utilisateur

Motorola

Motorola Netopia 2247NWG Manuel utilisateur

Motorola

Motorola 68230 - Vanguard 300 DSU/CSU Manuel

Motorola

Motorola MOTOWI 4 PTP 600 Series Manuel utilisateur

Motorola

Motorola MH7021 Manuel utilisateur

Motorola

Motorola BSR 64000 Manuel utilisateur

Motorola

Motorola 7640-47 Manuel

Motorola

Motorola BR700 - EN Broadband Router Mode d'emploi

Motorola

Motorola EX-3524 Manuel utilisateur

Motorola

Motorola PTP 300 Series Manuel utilisateur

Motorola

Motorola PTP 600 Series Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité

LevelOne

LevelOne FBR-1416 Manuel utilisateur