Motorola HC05F6 Manuel utilisateur
MOTOROLA
SEMICONDUCTOR
USER’S MANUAL
cMOTOROLA INC., 1994; All Rights Reserved
HC05F6EMUM/D
July, 1996
HC05F6
EMULATOR MODULE
USER’S MANUAL
First Edition
Motorola reserves the right to make changes without futher notice to any products herein to
improve reliability, function, or design. Motorola does not assume any liability arising out of the
application or use of any product or circuit described herein; neither does it convey any license
under its patent rights nor the rights of others. Motorola products are not designed, intended, or
authorized for use as components in systems intended for surgical implant into the body, or other
application in which the failure of the Motorola product could create a situation where personal
injury or death may occur. Should buyer purchase or use Motorola products for any such unin-
tended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers,
employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages,
and expanses, and reasonable attorney fees arising out of, directly or indirectly, any claim of per-
sonal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and the Motorola logo are registered trademarks of Motorola Inc.
Motorola Inc. is an Equal Opportunity/Affirmative Action Employer.
HC05F6EM USER”S MANUAL MOTOROLA
i
1
CONTENTS
CHAPTER 1 INTRODUCTION ........................................................................ 1-1
1.1 Development Systems .................................................................................. 1-1
1.1.1 Motorola Modular Development System (MMDS05) ...................... 1-1
1.1.2 M68HC05EVS Evaluation System (HC05EVS) ............................... 1-2
1.2 EM Layout ................................................................................................... 1-3
1.3 Connector Pin Assignments (P7 AND P8) .................................................. 1-4
CHAPTER 2 MMDS05 CONFIGURATION AND OPERATION .................... 2-1
2.1 Setting F6EM Jumper Headers .................................................................... 2-1
2.1.1 Reset Select Header (P4) ................................................................... 2-1
2.1.2 Clock Source Select Header (P6) ...................................................... 2-2
2.1.3 SCS1 Header (P9) .............................................................................. 2-3
2.1.4 SCS0 Header (P10) ............................................................................ 2-3
2.2 Installing Personality And Help Files .......................................................... 2-4
2.2.1 Personality File .................................................................................. 2-4
2.2.2 Help File ............................................................................................ 2-4
2.3 Remaining System Installation .................................................................... 2-5
CHAPTER 3 HC05EVS CONFIGURATION AND OPERATION ................... 3-1
3.1 Setting F6EM Jumper Headers .................................................................... 3-1
3.1.1 Reset Select Header (P4) ................................................................... 3-1
3.1.2 Clock Source Select Header (P6) ...................................................... 3-2
3.1.3 SCS1 Header (P9) .............................................................................. 3-3
3.1.4 SCS10 Header (P10) .......................................................................... 3-3
3.2 EVS Limitations ......................................................................................... 3-4
3.3 Logic Analyzer Connector P1 ...................................................................... 3-5
3.4 Remaining System Installation ................................................................... 3-7
HC05F6EM USER”S MANUAL
MOTOROLA
ii
1FIGURES
Figure Page
1-1 HC05F6 Emulator Module .......................................................................... 1-3
1-2 Connector P7 Pin Assignment ..................................................................... 1-4
1-3 Connector P8 Pin Assignment ..................................................................... 1-5
3-1 Connector P1 Pin Assignment ..................................................................... 3-5
TABLES
Table Page
3-1 Logic Analyzer Connector P1 Signal Descriptions ..................................... 3-6
HC05F6EM USER’S MANUAL MOTOROLA
1-1
1
CHAPTER 1 INTRODUCTION
This user’s manual explains connection, configuration, and operation
information specific to the HC05F6EM Emulator Module (hereafter
referred to as F6EM). The F6EM makes possible emulation and debug-
ging of MC68HC05F6 microcontroller unit (MCU) based target sys-
tems.
The F6EM can be part of two development systems. This chapter
describes those systems and explains the layout of the F6EM.
1.1 DEVELOPMENT SYSTEMS
Your F6EM can be part of two Motorola development tools: the HC05
Motorola Modular Development System (MMDS05) or the
M68HC05EVS Evaluation System (HC05EVS).
1.1.1 Motorola Modular Development System (MMDS05)
The MMDS05 is an emulator system that provides a bus state analyzer
and real-time memory windows. The unit’s integrated design environ-
ment includes an editor, an assembler, user interface, and source-level
debug. A complete MMDS05 consists of:
•a station module -- the metal MMDS05 enclosure, containing the
control board and the internal power supply. Most system cables
connect to the MMDS05 station module. (The cable to an optional
target system, however, runs through an aperture in the station mod-
ule enclosure to connect directly to the emulator module.)
•an emulator module (EM) -- such as the F6EM: a printed circuit
board that enables system functionality for a specific MCU. The EM
fits into the station module through a sliding panel in the enclosure
top. The EM has connectors for the target cable.
•two logic clip assemblies -- twisted-pair cables that connect the sta-
tion module to your target system, a test fixture, a clock, or any other
circuitry useful for evaluation or analysis. One end of each cable
assembly has a molded connector, which fits into station module pod
A and pod B. Leads at the other end of each cable terminate in
female probe tips. Ball clips come with the cable assemblies.
•a 9-lead RS-232 serial cable -- the cable that connects the station
module to the host computer RS-232 port.
•a 9 to 25-pin adapter -- a moulded assembly that lets you connect
the 9-lead cable to a 25-pin serial port.
•system software -- software, on 3-1/2 inch diskettes.
HC05F6EM USER’S MANUAL
MOTOROLA
1-2
1•MMDS05 documentation -- an MMDS05 operations manual
(MMDS05OM/D) and the appropriate EM user’s manual.
As mentioned, your F6EM gives the MMDS05 the ability to emulate the
MC68HC05F6 MCU. By substituting a different EM, you can enable
your MMDS05 to emulate an MCU of a different series. (Your Motorola
representative can explain all the EMs available.)
Chapter 2 explains how to configure and use your F6EM as part of an
MMDS05 system. For information about MMDS05 software or the sta-
tion module, see the MMDS05 operations manual. For layout and con-
figuration information pertaining to a different EM, see the
corresponding EM user’s manual.
1.1.2 M68HC05EVS Evaluation System (HC05EVS)
An HC05EVS is an economical, two-board tool for designing, debug-
ging, and evaluating target systems based on an MC68HC05 MCU. A
complete HC05EVS consists of:
•a platform board (PFB) -- the bottom board, which supports the
emulator module. The platform board has connectors for power and
for the terminal or host computer.
•an emulator module (EM) -- such as the F6EM: a printed circuit
board that enables system functionality for a specific MCU. The EM
fits onto the PFB. The EM has connectors for a target cable and a
cable to a logic analyzer.
•an RS-232 serial cable -- the cable that connects the PFB to the host
computer RS-232 port.
•system software -- software, on 3-1/2 inch diskettes.
•HC05EVS documentation -- an HC05EVS operations manual and
the appropriate EM user’s manual.
As mentioned, your HC05F6 EM emulates the MC68HC05F6 MCU.
By substituting a different EM, you can enable your HC05EVS to emu-
late an MCU of a different series. (Your Motorola representative can
explain all the EMs available.)
Chapter 3 explains how to configure and use your F6EM as part of an
HC05EVS system. For information about HC05EVS software or the
platform board, see the HC05EVS operations manual. For layout and
configuration information pertaining to a different EM, see the corre-
sponding EM user’s manual.
HC05F6EM USER’S MANUAL MOTOROLA
1-3
1
1.2 EM LAYOUT
Figure 1-1 shows the layout of the F6EM. Jumper header P4 controls the
path of a target reset. Jump header P6 lets you select the clock-signal
source. Jumper headers P9 and P10 enable you to define the state of bit
7 (SCS1) and bit 6 (SCS0) in the system option register ($002C) of the
MCU on power up or reset respectively.
Connectors P7 and P8, for a 44-pin QFP, a 64-pin QFP, or a 42-pin S-
DIP cable assembly, (purchased separately from the F6EM.) is the inter-
face to a target system. If you install the F6EM in the MMDS05 station
module, the target cable passes through the slit in the station module
enclosure. Connector P1 connects to a logic analyzer. (Connector P1 has
more significance for an EVS system, as an MMDS05 system includes
a bus analyzer.) Expansion header connectors P2 and P3 connect
together the EM and the control board (for an MMDS05) or the EM and
the platform board (for an EVS).
P7 P8
P1
P2 P3
Figure 1-1. HC05F6 Emulator Module
P4
P9
P6
P10
HC05F6EM USER’S MANUAL
MOTOROLA
1-4
11.3 CONNECTOR PIN ASSIGNMENTS (P7AND P8)
Figure 1-2 and 1-3 show the pin assignments for connectors P7 and P8.
For signal descriptions, consult the technical data book for the specific
MCU.
As connector P1 has more importance to an HC05EVS than to an
MMDS05, pin assignments for connector P1 are in Chapter 3.
To configure your F6EM for use as part of an MMDS05, follow the
instructions of Chapter 2. To configure your F6EM as part of an
HC05EVS, follow the instructions of Chapter 3.
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
PA41
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
P7
GND
NC
NC
PC0
PC2
EVDD
PC6
NC
TNX
GND
PD4
GND
NC
NC
PB0
PB2
NC
NC
PA0
PA2
GND
NC
PC1
PC3
PC4
PC7
NC
TCAP
PD1
PD5
GND
PD7
NC
PB4
PB6
GND
GND
Figure 1-2. Connector P7 Pin Assignments
PB1
PB3
HC05F6EM USER’S MANUAL MOTOROLA
1-5
1
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
PA31
3
5
7
9
11
13
15
17
19
21
23
27
29
31
33
35
37
39
P8
GND
PA5
/IRQ1
NC
GND
NC
PC5
NC
NC
TCMP
PD2
PD6
NC
GND
NC
GND
NC
PB5
PB7
PA1
NC
NC
/IRQ2
GND
NC
GND
NC
TNO
PD0
PD3
NC
NC
/RESET
GND
GND
NC
NC
GND
GND
Figure 1-3. Connector P8 Pin Assignments
25
HC05F6EM USER’S MANUAL MOTOROLA
2-1
2
CHAPTER 2 MMDS05 CONFIGURATION AND OPERATION
This chapter explains how to configure and use your F6EM as part of an
MMDS05. For other parts of system installation or configuration, see
the MMDS05 operations manual (MMDS05OM/D). (If you will use
your F6EM as part of an HC05EVS system, go to Chapter 3 for corre-
sponding information.)
Paragraph 2.1 explains how to set F6EM jumper headers. Paragraph 2.2
explains how to install personality and help files pertaining to the F6EM.
Paragraph 2.3 explains remaining system installation.
Note that you can configure an F6EM already installed in the MMDS05
station module enclosure. To do so, switch off station-module power,
remove the hatch, then follow the guidance of this chapter.
CAUTION
Be sure to switch off power if you reconfigure an
installed EM. Reconfiguring EM jumper headers with
power left on can damage MMDS05 circuits.
2.1 SETTING F6EM JUMPER HEADERS
Your F6EM has four jumper headers P4, P6, P9 and P10. Paragraphs
2.1.1.through 2.1.4 explain how to configure these headers.
2.1.1 Reset Select Header (P4)
Jumper header P4 controls the path of a target reset. The diagram below
shows the factory configuration: the fabricated jumper between pins 1
and 2 enables your software to control resets. This is the only correct P4
configuration for an F6EM that is part of an MMDS05.
1
2
3
P4
EVS
TARGET
FABRICATED
JUMPER
TARGET RESET
DRIVEN FROM
Table des matières
Autres manuels Motorola Unité de contrôle
Motorola
Motorola MVME2400 Series Guide de démarrage rapide
Motorola
Motorola MVME224A Series Manuel utilisateur
Motorola
Motorola 56F827 Instructions d'utilisation
Motorola
Motorola 56F8323 Manuel utilisateur
Motorola
Motorola M68EM05D32 Manuel utilisateur
Motorola
Motorola Canopy Subscriber Module Manuel utilisateur
Motorola
Motorola PRPMC750 Mode d’emploi
Motorola
Motorola MVME712-10 Manuel utilisateur
Motorola
Motorola MVME147 Guide de démarrage rapide
Motorola
Motorola Canopy Backhaul Module Manuel utilisateur
Motorola
Motorola MVME123 Manuel utilisateur
Motorola
Motorola HC05BS8 Manuel utilisateur
Motorola
Motorola SE955 Guide de configuration rapide
Motorola
Motorola DSP56852 Manuel utilisateur
Motorola
Motorola 56F8346 Manuel utilisateur
Motorola
Motorola DSP56F826EVM Instructions d'utilisation
Motorola
Motorola Canopy Manuel utilisateur
Motorola
Motorola MVME760 Manuel utilisateur
Motorola
Motorola MVME410 Manuel utilisateur
Motorola
Motorola C24 CDMA 1X Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
