Monoprice Blackbird 21614 Manuel utilisateur

MONOPRICE

Blackbird™4K Pro 4x1 Ultra Slim HDMI® Switch

P/N 21614

User's Manual

SAFETY WARNINGS AND GUIDELINES

Please read this entire manual before using this device, paying extra attention to these

safety warnings and guidelines. Please keep this manual in a safe place for future reference.

•This device is intended for indoor use only. Do not expose this device to water or

moisture of any kind. Do not place drinks or other containers with moisture on or

near the device. If moisture does get in or on the device, immediately unplug it from

the power outlet and allow it to fully dry before reapplying power.

•Do not touch the device, the power cord, or any other connected cables with wet

hands.

•Do not subject the product to extreme force, shock, or fluctuations in temperature

or humidity. Do not expose this device to excessive vibration.

•Do not expose this device to excessively high temperatures. Do not place it in, on,

or near heat sources, such as a fireplace, stove, radiator, etc. Do not leave it in direct

sunlight.

•Prior to operation, check the unit and power cord for physical damage. Do not use if

physical damage has occurred.

•Before plugging the unit into a power outlet, ensure that the outlet provides the

same type and level of power required by the device.

•Take care to prevent damage to the power cord. Do not allow it to become

crimped, pinched, walked on, or become tangled with other cords. Ensure that the

power cord does not present a tripping hazard.

•Unplug this device from the power source when not in use. Never unplug the unit

by pulling on the power cord. Always grasp the connector head or adapter body.

•Ensure that power is turned off and disconnected before making any electrical

connections.

•Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or

detergents. For stubborn deposits, moisten the cloth with warm water.

•This device has no user serviceable parts. Do not attempt to open, service, or

modify this device.

INTRODUCTION

Thank you for purchasing this Blackbird 4K Pro 4x1 Ultra Slim HDMI® Switch! This switch

allows you to connect up to four HDMI video sources to a single display. It supports video

resolutions up to 4K@60Hz, including 1080p@60Hz and 3D 1080p@60Hz. It provides

18Gbps bandwidth and supports HDCP™compliant video streams. It has a built-in signal

amplifier, which allows for the use of 24AWG passive HDMI cables at lengths up to 32 feet

(10 meters). It includes an infrared remote control (CR2032 battery not included) and

supports automated computer control using an RS-232 connection.

FEATURES

•Connects up to four HDMI® sources to a single HDMI display

•Compliant with the HDMI 2.0 and HDCP™2.2 specifications

•Provides 18Gbps bandwidth

•Supports video resolutions to 4K@60Hz 4:4:4, including 1080p@60Hz and 3D

1080p@60Hz

•Includes infrared remote control (CR2032 battery not included)

•Supports automated computer control using an RS-232 connection

•Includes six built-in EDID® modes and nine manually configurable EDID modes

•Supports the HDMI Consumer Electronics Control (CEC) feature

•Real-time switching status displayed on screen

•Built-in video amplifier allows for the use of 24AWG passive HDMI cable

•Micro USB power connector

•Supports firmware updates using the built-in USB port

CUSTOMER SERVICE

The Monoprice Customer Service department is dedicated to ensuring that your ordering,

purchasing, and delivery experience is second to none. If you have any problem with your

order, please give us an opportunity to make it right. You can contact a Monoprice

Customer Service representative through the Live Chat link on our website

www.monoprice.com or via email at sup[email protected]. Check the website for

support times and links.

PACKAGE CONTENTS

Please take an inventory of the package contents to ensure you have all the items listed

below. If anything is missing or damaged, please contact Monoprice Customer Service for a

replacement.

1x Blackbird 4K Pro 4x1 Ultra Slim HDMI® Switch

1x Infrared Remote Control (CR2032 battery not included)

1x IR Receiver

1x RS-232 cable

2x Mounting Ears

4x Mounting Screws

4x Plastic Feet

1x Micro USB AC Power Adapter (5 VDC, 2A)

1x User's Manual

PRODUCT OVERVIEW

Front Panel

1. SOURCE/MODE/3s: Momentarily press the button to switch to the next source in

the list. Press and hold the button for about 3 seconds to switch between Auto and

Manual switching modes.

2. POWER: The LED illuminates red when power is applied.

3. AUTO: The LED illuminates green when in Auto switching mode and is off when in

Manual switching mode.

4. INPUTS: The LED corresponding to the currently selected source device illuminates

green. The LEDs corresponding to the unselected sources illuminate orange.

Rear Panel

1. OUT:Connect to the display using a High Speed HDMI® Cable (not included).

2. IN #: Connect to the HDMI video sources using High Speed HDMI Cables (not

included).

3. RS232 Input Jack: 3.5mm jack for connecting the included RS-232 cable.

4. IR In: 3.5mm jack for connecting the included IR receiver.

5. EDID: Four DIP switches for using a fixed or user-defined EDID® setting.

6. FW/DC 5V: Micro USB port for powering the device or performing a firmware

update.

Remote Control

•INPUTS: Press one of the numbered buttons to

directly select the corresponding input. Press the

MANUAL/AUTO button to switch between Auto and

Manual switching mode. When in Auto switching

mode, the AUTO LED on the front panel illuminates

green.

•SOURCE: Use the buttons in the SOURCE area to

control the active video source device. Note that the

source devices must comply with the HDMI®

Consumer Electronics Control (CEC) feature to be

controlled using the included remote control.

•DISPLAY: Use the buttons in the DISPLAY area to

control the connected display. Note that the display

must comply with the HDMI® Consumer Electronics

Control (CEC) feature to be controlled using the

included remote control.

AUTO SWITCHING PRIORITY

The switch uses the following basic rules for selecting the input when Auto switching

mode is enabled.

•New Input: When a new input signal is detected, the switch will select that input

automatically.

•Power Rebooting: The switch automatically remembers the last selected input

when power is turned off. When power is turned back on, the switch will

automatically select the last selected input, if available. If the previously selected

input is no longer available, the switch will search for an input signal in the order 1-4

and will select the first detected input.

•Signal Loss: If the selected input signal is lost for any reason (e.g., source turned off),

the switch will detect all input signals in the order 1-4 and will select the first

detected input.

EDID MANAGEMENT

By default, the switch is set to pass the EDID® capabilities of the connected display to all

inputs. However, the EDID DIP switches on the rear panel allows you to select a predefined

fixed EDID setting or a custom, user-defined EDID. The following

table details the DIP switch settings for each selectable EDID

setting.

DIP Switch

EDID

0000

Pass through (default)

0001

1080p 3D stereo

0010

1080p 3D multichannel

0011

1080p 2D stereo

0100

1080p 2D multichannel

0101

3840x2160 2D (30Hz)

0110

3840x2160 2D (60Hz)

0111

User-defined

1000

User-defined

1001

User-defined

1010

User-defined

1011

User-defined

1100

User-defined

DIP Switch

EDID

1101

User-defined

1110

User-defined

1111

User-defined

SAMPLE CONNECTION DIAGRAM

INSTALLATION

Perform the following steps to install this splitter into your home theater system.

1. Ensure that all equipment to be connected is powered off and unplugged from its

power source.

2. Place or mount the splitter in its intended location.

3. Using a High Speed HDMI® Cable (not included), plug one end into the HDMI input

on your display, then plug the other end into the OUT port on the splitter.

4. Using a High Speed HDMI Cable (not included), plug one end into one of the IN

ports on the splitter, then plug the other end into the HDMI output on your video

source device. Repeat for up to three additional video source devices.

5. Plug the Micro USB connector on the included AC power adapter into the FW/DC

5V port on the splitter, then plug the adapter into a nearby AC power outlet. The

POWER LED will illuminate red.

6. Plug in and power on the display.

7. Plug in and power on your HDMI video source devices. Start playback of video

content. The INPUT LED corresponding to the selected input illuminates green,

while the remaining INPUT LEDs illuminate orange.

8. Cycle through the connected inputs to verify that there is video on the display for

each source device.

Congratulations, your splitter is properly installed and ready for use!

RS-232 CONTROL

The matrix can be controlled using RS-232 commands issued from RS-232 control software.

Before you can issue RS-232 commands, you must plug one end of the included RS-232

Cable into the RS232 jack on the matrix rear panel, then plug the other end into an

available serial port on your computer.

Next, you need to download and install RS-232 control

software. A common freeware RS-232 control software is

CommWatch.exe, which this section will use as an example,

but other software can be used instead.

The default communications parameters are:

Baud Rate: 9600

Data Bits: 8

Stop Bits: 1

Parity: None

Table des matières

Autres manuels Monoprice Changer

Monoprice

Monoprice Blackbird Manuel utilisateur

Monoprice

Monoprice Blackbird 36633 Manuel utilisateur

Monoprice

Monoprice 36737 Manuel utilisateur

Monoprice

Monoprice HD-140E3-3D 1x4 Pro Series Manuel utilisateur

Monoprice

Monoprice DRM-1712F+ Manuel utilisateur

Monoprice

Monoprice 33416 Manuel utilisateur

Monoprice

Monoprice 38295 Manuel utilisateur

Monoprice

Monoprice HD-411E3 Manuel utilisateur

Monoprice

Monoprice 611680 Manuel utilisateur

Monoprice

Monoprice 31056 Manuel utilisateur

Monoprice

Monoprice Blackbird 33418 Manuel utilisateur

Monoprice

Monoprice 24740 Manuel utilisateur

Monoprice

Monoprice Blackbird 36632 Manuel utilisateur

Monoprice

Monoprice BLACKBIRD 44556 Manuel utilisateur

Monoprice

Monoprice Blackbird 39671 Manuel utilisateur

Monoprice

Monoprice 15261 Manuel utilisateur

Monoprice

Monoprice PID 11752 Manuel utilisateur

Monoprice

Monoprice 38161 Manuel utilisateur

Monoprice

Monoprice 24280 Manuel utilisateur

Monoprice

Monoprice Blackbird 33417 Manuel utilisateur

Monoprice

Monoprice 36653 Manuel utilisateur

Monoprice

Monoprice 30919 Manuel utilisateur

Monoprice

Monoprice HDX-401E Manuel utilisateur

Monoprice

Monoprice Blackbird Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur