Mitsubishi Lancer Evolution VII Manuel utilisateur

EXTERIOR – GENERAL 51-1

SECTION 51

EXTERIOR

CONTENTS

GENERAL

New servicing information now applies with the following changes and additions. Apart from the information below, servicing is

the same as the Lancer Evolution VII.

• Changes in the shape of the front bumper and addition of new components

• Addition of components due to changes in rear spoiler shape, and change in the positioning of double-sided adhesive tape

• Change in the shape of three diamond mark, EVOLUTION mark and LANCER mark, and change in the positioning of

EVOLUTION mark and LANCER mark.

Gene al .......................................................1

F ont bumpe ...........................................2

Adhesives................................................2

Front bumper ..........................................2

Rea spoile ...............................................4

Adhesive .................................................4

Rear spoiler ............................................

Ma ks ..........................................................6

EXTERIOR – FRONT BUMPER

51-2

F ont Bumpe

Adhesive

F ont bumpe

Removal and Installation

Removal p ocedu e

1. Side under cover

2. Centre under cover

3. Under cover centre bracket

4. Front under cover

• Splash shield installation clip

• Water spray hose connection (see Chapter 1 )

. Front bumper assembly

Section A-A

clip

Section B-B

clip

Section C-C

Application Brand

Three Diamond Mark Double-sided tape: Generic product (width 20 mm, thickness 0.8 mm)

fender

EXTERIOR – FRONT BUMPER 51-3

Double-sided tape: Gene ic tape

Width: 20 mm; Thickness 0.8 mm

Disassembly and Reassembly

Clip

Section A-A Section B-B

EXTERIOR – FRONT BUMPER, REAR SPOILER

51-4

Disassembly P ocedu e

1. Three diamond mark

2. Licence plate trim

3. Licence plate bracket

4. Licence plate bracket assembly

. Cover

6. Front air dam panel

7. Front bumper lower plate assembly

8. Front bumper lower reinforcement

assembly

9. Front bumper reinforcement assembly

10.Bumper net

11. Front bumper side cover

12. Bumper side net (LH)

13. Oil cooler duct

14. Bumper side net (RH)

• Water spray hose and nozzle

(see Chap. 1 )

1 . Front bumper side plate assembly

16. Front bumper upper reinforcement

assembly

17. Front bumper face

Disassembly se vice points

ARemoval of f ont bumpe side plate

Use the same procedure as that for removal of front bumper rivets

in previous model.

Reassembly se vice points

A Installation of f ont bumpe side plate

Use the same procedure as that for installation of front bumper

rivets in previous model.

Rea Spoile

Adhesive

AA

Application Brand

Rear Spoiler Double-sided tape : Generic product A (width mm, thickness 0.8 mm); B (width mm,

thickness 1.2 mm)

Double-sided tape removing agent : Sumitomo 3M 4000 double-sided tape remover (made

by Sumitomo 3M)

Primer : Sumitomo 3M 8107 parts primer (made by Sumitomo 3M)

EXTERIOR – REAR SPOILER 51-5

Rea Spoile

Removal and Installation

Removal p ocedu e

• Boot lid bumper

1. Cap

2. Rear spoiler

Double-sided tape: Gene ic p oducts A: width 5 mm, thickness 0.8 mm,

B: width 5 mm, thickness 1.2 mm

P ime : Sumitomo 3M 8107 PP pa ts p ime

Remarks :

The removal and installation service points are the same as those for the air dam, bumper moulding, wing and door moulding

in the previous model.

AA

EXTERIOR – MARKS

51-6

Ma ks

Removal and Installation

1. Three diamond mark

A2. LANCER mark

A 3. EVOLUTION mark

Installation se vice points

AInstallation of ma ks

1. Installation position

(2) LANCER ma k

Boot lid end line

EXTERIOR – MARKS 51-7

(3) EVOLUTION mark

2. Installation p ocedu e

(1) Remove grease from installation surface of the body, using unleaded

gasoline.

(2) Peel off the protective backing of the mark and apply it to the installation

position.

Caution

1) Pe fo m this ope ation in a dust-f ee envi onment at a oom tempe atu e

of 20 – 38°C.

2) If the oom tempe atu e is less than 20°C, then the ma k and body

(installation position) must be heated to 20 – 30°C.

3) The ma k must be p essed to eliminate any ai bubbles.

Boot lid end line

Table des matières

Autres manuels Mitsubishi Automobile

Mitsubishi

Mitsubishi LANCER 2012 Manuel utilisateur

Mitsubishi

Mitsubishi i-MiEV 2011 Manuel utilisateur

Mitsubishi

Mitsubishi ECLIPSE Manuel utilisateur

Mitsubishi

Mitsubishi Galant 1997 Manuel d'instructions

Mitsubishi

Mitsubishi LANCER 2014 SERIES Guide de l'utilisateur

Mitsubishi

Mitsubishi Lancer Family Guide de l'utilisateur

Mitsubishi

Mitsubishi MIRAGE 2014 Guide de l'utilisateur

Mitsubishi

Mitsubishi Lancer Evolution-VII Manuel d'instructions

Mitsubishi

Mitsubishi 1989-1993 GALANT Manuel utilisateur

Mitsubishi

Mitsubishi Outlander 2007 Manuel utilisateur

Mitsubishi

Mitsubishi ASX 2016 Manuel utilisateur

Mitsubishi

Mitsubishi 2005 Outlander Guide de l'utilisateur

Mitsubishi

Mitsubishi Pick-Up 1987 Manuel utilisateur

Mitsubishi

Mitsubishi Outlander Sport 2019 Guide de l'utilisateur

Mitsubishi

Mitsubishi 2013 Outlander Manuel utilisateur

Mitsubishi

Mitsubishi 2009 Lancer RalliArt Manuel utilisateur

Mitsubishi

Mitsubishi LANCER Manuel utilisateur

Mitsubishi

Mitsubishi Lancer Evolution-VI Manuel d'instructions

Mitsubishi

Mitsubishi OUTLANDER Manuel utilisateur

Mitsubishi

Mitsubishi Galant Manuel utilisateur

Mitsubishi

Mitsubishi ECLIPSE Manuel utilisateur

Mitsubishi

Mitsubishi i-Miev 2012 Manuel utilisateur

Mitsubishi

Mitsubishi LANCER Manuel utilisateur

Mitsubishi

Mitsubishi PAJERO IV Manuel utilisateur

Manuels Automobile populaires d'autres marques

Toyota

Toyota 2000 Tundra Manuel utilisateur

CITROËN

CITROËN DS4 DSign Manuel utilisateur

Lexus

Lexus 2015 CT 200h Manuel utilisateur

Cadillac

Cadillac CTS 2008 Manuel utilisateur

Mercedes-Benz

Mercedes-Benz M-class ML 55 AMG Manuel utilisateur

Porsche

Porsche Boxster S Manuel utilisateur

GMC

GMC 2010 Savana 1500 Cargo Manuel utilisateur

KIAM

KIAM SPORTAGE 2014 Manuel de la liste des pièces

GMC

GMC 2013 Terrain Instructions de montage

GMC

GMC T-Series 1999 Manuel utilisateur

Mercury

Mercury 1998 Mystique Manuel utilisateur

Mercury

Mercury 2007 Mariner Manuel utilisateur

Mazda

Mazda 2007 Mazdaspeed 3 Mode d’emploi

Mazda

Mazda 2014 CX-5 Manuel utilisateur

GMC

GMC Chevrolet Express 2022 Manuel utilisateur

GMC

GMC 1997 Jimmy Manuel utilisateur

Chevrolet

Chevrolet 2012 Malibu Manuel utilisateur

Cadillac

Cadillac 2010 Escalade Manuel utilisateur