Milwaukee SM500 Manuel utilisateur

Milwaukee

USER MANUAL

PORTABLE

ORP METER

MODEL: SM500

Smart ORP Meter

ISMIL500 11/01

SPECIFICATIONS:

SM500

RANGE ±1000 mV

RESOLUTION 1 mV

ACCURACY (@25°C) ±5 mV

ORP ELECTRODE MA921B/1 (included)

ENVIRONMENT 0 to 50°C, 95% RH max.

BATTERY TYPE 9V alkaline (included)

BATTERY LIFE approximately 300 hours of use

DIMENSIONS 145 x 80 x 40 mm

WEIGHT 220 g (with battery) meter only

OPTIONAL ACCESSORIES:

M10000B Electrode rinse solution, 20 ml sachet (25 pcs)

MA9015 Electrode storage solution, 220 ml bottle

MA9020 200-275 mV ORP solution, 220 ml bottle

MA921B/1 Platinum ORP electrode with 1 m cable

WARRANTY:

This instrument is warranted from all defects in materials and

manufacturing for a period of two years from the date of purchase.

The electrode is warranted for a period of 6 months.

If during this period, the repair or replacement of parts is required,

where the damage is not due to negligence or erroneous operation

by the user, please return the parts to either dealer or our office

and the repair will be effected free of charge.

Note: We reserve the right to modify the design, construction and

appearance of our products without advance notice.

Milwaukee

OPERATION:

• The meter is supplied complete with a 9V battery. Slide off

the battery compartment cover on the back of the meter.

Install the battery while paying attention to its polarity.

• Always remove the electrode protective cap before taking

any measurement. If the electrode has been left dry, soak

the tip in storage solution for a few

minutes to reactivate it.

• Connect the ORP electrode to the

BNC socket on the top of the meter.

• Immerse the tip (2.5 cm) of the ORP

electrode into the sample.

• Turn the instrument on by pressing

the ON/OFF key.

• Allow the reading to stabilize before

taking measurements.

• After use, switch the meter off and

store the electrode with a few drops

of storage solution in the protective

cap.

• The meter is factory calibrated. ORP

electrodes are inter-changeable and

no mV calibration is needed when

they are replaced.

MAINTENANCE:

• To correctly perfom a redox measurement, the surface of

the ORP electrode must always be clean. Use for this

purpose the M10000B rinse solution. If needed, brush the

Platinum tip with very fine abrasive paper.

• When not in use, the tip of the electrode should always be

kept moist and safe from any mechanical stress.

BATTERY REPLACEMENT:

When the battery becomes weak the meter will display "S".

When the low battery indicator appears, the battery has only

about 50 hours of working time left. A low battery will result in

unreliable measurements. It is recommended to replace the

battery immediately.

Battery replacement must only take place in a non hazardous

area using an alkaline 9V battery.

Turn the meter off, slide off the battery compartment cover at

the rear of the meter and replace the 9V battery with a new

one. Make sure the battery contacts are tight and secure, seat

the battery in its compartment and insert the cover again.

Autres manuels Milwaukee Instrument de mesure

Milwaukee

Milwaukee MW150 Manuel utilisateur

Milwaukee

Milwaukee MW102 Manuel utilisateur

Milwaukee

Milwaukee LDM 45 Manuel utilisateur

Milwaukee

Milwaukee MW102 Manuel utilisateur

Milwaukee

Milwaukee MA881 Manuel utilisateur

Milwaukee

Milwaukee M12 ICAV3 Manuel utilisateur

Milwaukee

Milwaukee M12 CLLP-301C Manuel utilisateur

Milwaukee

Milwaukee PRO MW801 Manuel utilisateur

Milwaukee

Milwaukee MI455 Manuel utilisateur

Milwaukee

Milwaukee 2205-20 Manuel utilisateur

Milwaukee

Milwaukee MW190 MAX Manuel utilisateur

Milwaukee

Milwaukee 3712 Manuel utilisateur

Milwaukee

Milwaukee pH54 Manuel utilisateur

Milwaukee

Milwaukee MW101 Manuel utilisateur

Milwaukee

Milwaukee M12 3632-20 Manuel utilisateur

Milwaukee

Milwaukee MW 14 Manuel utilisateur

Milwaukee

Milwaukee MA888 Manuel utilisateur

Milwaukee

Milwaukee C 12 IC AVD Manuel utilisateur

Milwaukee

Milwaukee MI406 Manuel utilisateur

Milwaukee

Milwaukee Heavy Duty 2270-20 Manuel utilisateur

Milwaukee

Milwaukee PH55 Manuel utilisateur

Milwaukee

Milwaukee MI407 Manuel utilisateur

Milwaukee

Milwaukee 2212-20 Manuel utilisateur

Milwaukee

Milwaukee MW101 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur