Milwaukee MC310 Manuel utilisateur

OPERATION:

• Connect the supplied 12

VDC power adapter to the

meter and to the mains.

• Make sure the meter has

been calibrated before tak-

ing any measurements (see

Calibration Procedure).

• Immerse the tip (4cm) of the

Conductivity probe into the

sample.

• Turn the instrument on by

pressing the ON/OFF key.

• Wait for thermal equilibrium to be reached and the meter will

start continuous monitoring.

• Set the BELOW / ABOVE alarm activation switch in the

desired position.

• A blinking alarm will indicate when the measured EC or TDS

value is lower/higher than the setpoint (in accordance the

BELOW / ABOVE switch).

SETPOINT:

• The setpoint can be selected

by adjusting the central front

knob to the desired value.

• The selectable range for

MC310 is from 1.0 to 5.0

mS/cm.

The selectable range for

MC410 and for MC410A is

from 700 to 1900 ppm.

CALIBRATION PROCEDURE:

• Clean the probe with alcohol and let it dry (if a

more thorough cleaning is required, brush the

metal pins with fine sandpaper and then rinse

with water).

• Open a sachet of suitable conductivity calibration

solution and immerse the probe, making sure that

metal pins are completely submerged.

Use M10039 (5.00 mS/cm) for MC310, M10442

(1500 ppm) for MC410 and M10032 (1382 ppm)

for MC410A.

• Turn the meter on by pressing the ON/OFF key.

• Wait until the reading stabilize for temperature variations, and

then adjust the EC/TDS calibration trimmer on the front panel

with the supplied screwdriver until the display shows: "5.0"

mS/cm for MC310, "1500" ppm for MC410 and "1380" ppm for

MC410A.

The calibration is now complete and the meter is ready for use.

The instrument should be re-calibrated at least once a month,

or when the probe is changed.

OPTIONAL ACCESSORIES:

M10039B 5.00 mS/cm cal. solution, 20 mL sachet (25 pcs)

M10442B 1500 ppm cal. solution, 20 mL sachet (25 pcs)

M10032B 1382 ppm cal. solution, 20 mL sachet (25 pcs)

MA812/2 Conductivity probe with 2 m cable

SPECIFICATIONS:

RANGE MC310 0.0 to 10.0 mS/cm

MC410 0 to 1990 ppm

RESOLUTION

MC310 0.1 mS/cm

MC410, MC410A 10 ppm

ACCURACY (@25°C) ±2% Full Scale

CONVERSION FACTOR

MC410 0.7

MC410A 0.5

SETPOINT

MC310 1.0 to 5.0 mS/cm

MC410, MC410A 100 to 1900 ppm

ALARM active when the measure is below/

above than the setpoint, in according

with the BELOW/ABOVE switch

TEMP.COMPENSATION Automatic, from 0 to 50°C

ENVIRONMENT 0 to 50°C; 95% RH max.

PROBE MA812/2 (included)*

POWER SUPPLY 12 VDC adapter (included)

DIMENSIONS 148.5 x 82.5 x 32 mm

WEIGHT 180 g (meter only)

(*) To be replace by technical personnel only

These instruments are warranted fromall defects in materialsand manufacturing fora period oftwo

yearsfrom the dateof purchase. The probes are warranted for a period of 6 months if during this

period, the repairor replacement of parts is required, where the damage is not due to negligence or

erroneous operation by the user, please return the parts to either dealer or our office and the repair

will be effected free of charge.

WARRANTY:

Note: We reserve the right to modify the design, construction and appearance of our products

without advance notice.

USER MANUAL

CONDUCTIVITY & TDS METERS

MODELS: MC310, MC410, MC410A

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Milwaukee Instrument de mesure

Milwaukee

Milwaukee MI 404 Manuel utilisateur

Milwaukee

Milwaukee C12 CMH Manuel utilisateur

Milwaukee

Milwaukee 2205-40 Manuel utilisateur

Milwaukee

Milwaukee MW802 Manuel utilisateur

Milwaukee

Milwaukee pH51 Manuel utilisateur

Milwaukee

Milwaukee MW306 MAX Manuel utilisateur

Milwaukee

Milwaukee M12 C4PLA Manuel utilisateur

Milwaukee

Milwaukee MC125 Manuel utilisateur

Milwaukee

Milwaukee pH600 Manuel utilisateur

Milwaukee

Milwaukee 2217-40 Manuel utilisateur

Milwaukee

Milwaukee PRO MI414 Manuel utilisateur

Milwaukee

Milwaukee SM700 Manuel utilisateur

Milwaukee

Milwaukee LDM 45 Manuel utilisateur

Milwaukee

Milwaukee MI 406 Manuel utilisateur

Milwaukee

Milwaukee MW190 Manuel utilisateur

Milwaukee

Milwaukee M12 SUB-SCANNER 2291-20 Manuel utilisateur

Milwaukee

Milwaukee MA882 Manuel utilisateur

Milwaukee

Milwaukee MW190 MAX Manuel utilisateur

Milwaukee

Milwaukee M12 CPL Manuel utilisateur

Milwaukee

Milwaukee L4 CLL Manuel utilisateur

Milwaukee

Milwaukee M12 AL Manuel utilisateur

Milwaukee

Milwaukee MW10 Manuel utilisateur

Milwaukee

Milwaukee MW101 Manuel utilisateur

Milwaukee

Milwaukee Mi170 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur