Milwaukee MC730 Manuel utilisateur

Mount the bracket in the wall in upright position above the water

container (which contains a solution of pH reducing acid and

water).

Place the pump in vertical position (with the tubes below) on the

wall, above and centered with the “Mounting bracket“. Then go

down the pump until it is joined with the bracket.

Connect the pump to the MC122 pH controller (on the black and

white outlet). The pump will discharge 0,08 cL every 2 seconds.

Place the plug and B/W outlet far away from water!

Before servicing (maintenance) on the pump (e.g. changing

tube), please disconnect the equipment.

USER MANUAL

MC730

MILWAUKEE MC122 PH CONTROLLER

WITH MP815 DOSING PUMP

It is suggested to dissolve 10 cL of pH reducing acid in a 5L container of mineral water.

Depending on the volume of your tank and the brand of you pH reducing acid (if it is

more or less concentrated), this quantity will be balanced. It is better to dissolve more

than less. It is suggested to use an airstone on the bottom of your tank. The pump can

be attached directly to the container of the solution.

OPTIONALACCESSORIES:

M10004B pH 4.01 buffer solution, 20 ml sachet (25 pcs)

M10007B pH 7.01 buffer solution, 20 ml sachet (25 pcs)

SPECIFICATIONS

Smart Monitoring System

M10010B pH 10.01 buffer solution, 20 ml sachet (25 pcs)

M10000B Electrode rinse solution, 20 ml sachet (25 pcs)

MA9015 Electrode storage solution, 20 ml sachet (25 pcs)

WARRANTY:

These instruments are warranted from all defects in materials and manufacturing for a period of two years

from the date of purchase. The electrode is warranted for a period of 6 months.

If during this period, the repair or replacement of parts is required, where the damage is not due to negli-

gence or erroneous operation by the user, please return the parts to either dealer or our office and the repair

will be effected free of charge.

Note: We reserve the right to modify the design, construction and appearance of our products without ad-

vance notice.

www.milwaukeeinst.com

MC122 pH Meter

Range

0.0 to 14.0 pH

Resolution

0.1 pH

Accuracy

±0.2 pH (@25°C)

Setpoint

5.5 to 9.5 pH

Alarm / Output active when measure is

Power Socket higher/lower than selected

setpoint depending on

user selection

Power drivers 115VAC, 2A, 60Hz

or 230VAC, 1A, 50Hz

pH electrode MA911B/2 (included)

Environment

0 to 50°C, 95% RH

not condensing

Power supply 12 VDC (included)

Dimensions

148.5 x 82.5 x 32 mm

Weight

180 g

MP815 Peristaltic Dosing Pump

Adjustable dosing flow of 0,0 –2,2 l/h

(0,0 - 37 mL/min)

Maximum pressure: 2 bar

Made of Polipropilene (PP)

Peristaltic tube is Santoprene

Power supply: 240 VAC ± 10%

INSTALLATIONOF CONTROLLER:

Connect the supplied 240VAC/12VDC power adapter to the

meter and to the main line.

Connect the connection base (black and white outlet) to the

main line.

Connect the pH-electrode to the BNC socket on the bottom of

the meter.

Always remove the electrode protective cap before taking any

measurement. Make sure that the meter has been calibrated

before taking any measurements

Immerse the tip (2.5 cm) of the pH-electrode into the sample.

(for example it can float with the help of a piece of polystyrol).

Turn the instrument on by pressing the ON/OFF button.

The nature of the setpoint can be selected by setting the switch

to the desired position (ABOVE or BELOW).

Allow the reading to stabilize and the meter will start continuous

monitoring.

A blinking alarm will indicate when the measured pH value is

higher or lower than selected setpoint, depending on user

selection. When the alarm is activated, it also activates the

connection base and the auxiliary equipment.

The setpoint can be selected by adjusting the central front knob

to the desired value. The selectable range is from 5.5 to 9.5 pH.

CALIBRATION:

•Remove the protective cap from the electrode.

•Immerse the electrode tip into a new sachet of pH 7 calibration

solution and allow the reading to stabilize.

•Adjust the pH7 calibration trimmer (on the front) to display “7.0

pH”.

•Rinse the electrode with tap water and dry it with paper tissue.

•Open a new sachet of pH 4 calibration solution, immerse the

electrode tip into the sachet and allow the reading to stabilize.

•Adjust the pH4/10 calibration trimmer (on the front) to display

“4.0 pH”.

The calibration is now complete and the meter is ready to take

measurements.

It is suggested to recalibrate the meter at least once a month,

after a prolonged stocking time and after pH-electrode

replacement.

INSTALLATION OF THE

MP815 DOSING PUMP

Connect the rigid tube to the pump (aspiration –arrow upwards).

Fix the white filter on the other end of the tube, where the dis-

solved pH reducing acid will be drawn in –to prevent small ob-

jects entering the pump.

Connect the soft tube to the pump (impulsion –arrow down-

wards). The injection fitting will be placed at the end of this tube

only to inject into a piping. (This fitting has a thread that links it

to the piping.)

Autres manuels Milwaukee Instrument de mesure

Milwaukee

Milwaukee SMS510 Manuel utilisateur

Milwaukee

Milwaukee SM500 Manuel utilisateur

Milwaukee

Milwaukee C12 CMH Manuel utilisateur

Milwaukee

Milwaukee MW180 MAX Manuel utilisateur

Milwaukee

Milwaukee MW10 Manuel utilisateur

Milwaukee

Milwaukee MW102 Manuel utilisateur

Milwaukee

Milwaukee 2217-40 Manuel utilisateur

Milwaukee

Milwaukee MI 806 Manuel utilisateur

Milwaukee

Milwaukee PRO MI415 Manuel utilisateur

Milwaukee

Milwaukee MW13 Manuel utilisateur

Milwaukee

Milwaukee MW802 Manuel utilisateur

Milwaukee

Milwaukee pH600 Manuel utilisateur

Milwaukee

Milwaukee MI 404 Manuel utilisateur

Milwaukee

Milwaukee MI415 Manuel utilisateur

Milwaukee

Milwaukee pH 58 Manuel utilisateur

Milwaukee

Milwaukee SM100 Manuel utilisateur

Milwaukee

Milwaukee MAX MW160 Manuel utilisateur

Milwaukee

Milwaukee MC110 Manuel utilisateur

Milwaukee

Milwaukee MW102 Manuel utilisateur

Milwaukee

Milwaukee MA871 Manuel utilisateur

Milwaukee

Milwaukee M12 C4PLA Manuel utilisateur

Milwaukee

Milwaukee pH51 Manuel utilisateur

Milwaukee

Milwaukee MW14 Manuel utilisateur

Milwaukee

Milwaukee MI408 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur