Milwaukee MC125 Manuel utilisateur

USER MANUAL

MC125

PRO Digital pH/ORP

Controller

SPECIFICATIONS

pH ORP

Range 0.0 to 14.0 pH ±1000 mV

Resolution 0.01 pH 1 mV

Accuracy

(@25°C) ±0.2 pH ± 5 mV

Setpoint 4 to 8 pH -200 to 600 mV

Electrode

(included) MA911B/2 MA921B/2

Alarm & Output

Power Socket

active when measurement is

higher/lower than the setpoint

depending on user selection

Environment 0 to 50°C, 95% RH max.

Power Supply 12 VDC (included)

Power Drivers 115VAC, 2A, 60Hz or 230VAC, 1A, 50Hz

Dimensions 148.5 x 82.5 x 32 mm

Weight 200 g (meter only)

OPTIONAL ACCESSORIES

M10004B pH 4.01 buer solution, 20 ml sachet (25pcs)

M10007B pH 7.01 buer solution, 20 ml sachet (25pcs)

M10010B pH 10.01 buer solution, 20 ml sachet

(25pcs)

M10000B Electrode rinse solution, 20 ml sachet

(25pcs)

MA9015 Electrode storage solution, 20 ml sachet

(25pcs)

CERTIFICATION

Milwaukee Instruments conform to the CE

European Directives.

Disposal of Electrical & Electronic

Equipment. Do not treat this product

as household waste. Hand it over to the

appropriate collection point for the recycling

of electrical and electronic equipment.

Please note: proper product prevents potential

negative consequences for human health and the

environment. For detailed information, contact your

local household waste disposal service or go to

www.milwaukeeinstruments.com (USA & CAN) or

www.milwaukeeinst.com.

RECOMMENDATION

Before using this product, make sure it is entirely

suitable for your specific application and for the

environment in which it is used. Any modification

introduced by the user to the supplied equipment

may compromise the meter’s performance. For your

and the meter’s safety do not use or store the meter in

hazardous environment. To avoid damage or burn, do

not perform any measurement in microwave ovens.

WARRANTY

This instrument is warranted against defects in

materials and manufacturing for a period of 2years

from the date of purchase. Probe is warranted for

6 months. This warranty is limited to repair or free

of charge replacement if the instrument cannot be

repaired. Damage due to accidents, misuse, tampering

or lack of prescribed maintenance is not covered by

warranty. If service is required, contact your local

Milwaukee Instruments Technical Service. If the repair

is not covered by the warranty, you will be notified of

the charges incurred. When shipping any meter, make

sure it is properly packaged for complete protection.

We reserve the right to modify the design,

construction and appearance of our products

without advance notice.

ISTMC125_07_20

RoHS

COMPLIANT

SATISFACTION

GUARANTEED Distributor in AustraliaPacific Sensor Technologies Pty LtdUnit 4, 3 Neutron Place Rowville, VIC 3178 Australia1300 662 720 | [email protected]www.pacificsensortech.com.au

OPERATION

yConnect the supplied 12 VDC power adapter to the

meter and to the mains line.

yConnect the pH and ORP electrode to the BNC

socket of the meter.

yAlways remove the electrode protective caps

before taking any measurement. If the electrodes

have been left dry, soak the tip (bottom 2.5 cm)

in rinse solution (M10000B) for a few minutes to

reactivate them.

yMake sure that the meter has been calibrated

before taking any measurements (see Calibration

Procedure).

yImmerse the tip (2.5 cm) of the electrodes into the

samples.

yTurn the instrument on by pressing the ON/OFF key.

yAllow the reading to stabilize and the meter will

start continuous monitoring.

yA blinking alarm LED will indicate when the

measured pH value is higher or lower than the

setpoint depending on user selection.

yWhen the alarm LED is blinking, there is power in

the output power socket.

Note: The output power contact has no protection

fuse inside the meter. It is recommended to protected

it outside, against failure.

SETPOINT

yThe setpoint can be selected by adjusting the knob

to the desired value.

yThe selectable range for MC125 is from 4 to 8 for pH

and from -200 to 600 mV for ORP.

yThe nature of the setpoint can be selected by

setting the proper switch to the desired position

(ABOVE or BELOW).

CALIBRATION PROCEDURE

yRemove the protective cap from the pH electrode.

yImmerse the electrode tip into a new sachet of

pH 7calibration solution and allow the reading to

stabilize.

yAdjust the pH7 calibration trimmer (on the front) to

display “7.00 pH”.

yOpen a new sachet of pH 4 calibration solution and

use a small quantity to rinse the electrode.

yImmerse the electrode tip inside the pH 4 sachet

and allow the reading to stabilize.

yAdjust the pH4/10 calibration trimmer (on the front)

to display “4.00 pH”.

yThe calibration is now complete and the meter is

ready to take measurements.

yIt is suggested to recalibrate the meter at least once

a month, after prolonged warehousing time and

after pH electrode replacement.

INSTALLATION PROCEDURE

Autres manuels Milwaukee Instrument de mesure

Milwaukee

Milwaukee MW190 MAX Manuel utilisateur

Milwaukee

Milwaukee 3421 Manuel utilisateur

Milwaukee

Milwaukee MI 413 Manuel utilisateur

Milwaukee

Milwaukee 2280-20 Manuel utilisateur

Milwaukee

Milwaukee MA872 Manuel utilisateur

Milwaukee

Milwaukee LDM 30 Manuel utilisateur

Milwaukee

Milwaukee MW301 Manuel utilisateur

Milwaukee

Milwaukee M12 3622-20 Manuel utilisateur

Milwaukee

Milwaukee MW803 Manuel utilisateur

Milwaukee

Milwaukee MW700 Manuel utilisateur

Milwaukee

Milwaukee MC110 Manuel utilisateur

Milwaukee

Milwaukee MA871 Manuel utilisateur

Milwaukee

Milwaukee MI415 Manuel utilisateur

Milwaukee

Milwaukee Mi 180 Manuel utilisateur

Milwaukee

Milwaukee SM101 Manuel utilisateur

Milwaukee

Milwaukee MW500 Manuel utilisateur

Milwaukee

Milwaukee 2205-40 Manuel utilisateur

Milwaukee

Milwaukee PRO MW801 Manuel utilisateur

Milwaukee

Milwaukee MW105 MAX Manuel utilisateur

Milwaukee

Milwaukee 2205-20 Manuel utilisateur

Milwaukee

Milwaukee LDM 30 Manuel utilisateur

Milwaukee

Milwaukee CALIBRATION 2238-20 Manuel utilisateur

Milwaukee

Milwaukee MI 411 Manuel utilisateur

Milwaukee

Milwaukee MC310 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur