MELICONI FACILE Manuel utilisateur
Thank you for choosing Meliconi.
The spare FACILE remote control can be used for all the main functions
for TVs of the makes listed at the back of the pack.
Keep your Instructions Booklet and Code Booklet for future reference.
USING THE BUTTONS AND FUNCTIONS
Light indicator.
Confirm button.
To select the next (P+)
or previous (P-)
channel or program.
These buttons can
also be used to move
up and down
in the MENU.
Mute button.
Additional colour button
or function.
TV ON/OFF button.
Fastext functions
or access to the
brightness and colour
controls, directly or
using the SHIFT button.
Teletext buttons:
to access Teletext
to close Teletext and
return to normal
viewing Teletext page
hold function.
Number keys.
To access your MENU.
To move within the MENU,
use the +/- and P +/-
or SHIFT buttons together
with +/- P +/- depending
on the model of your
original remote control.
Control the volume using +/ -.
These buttons can also be
used to move to the right
and left in the MENU.
To select an external terminal.
Used to access additional
commands and to program
the remote control.
The functions described above are only operative
if your appliance also has them.
GB Use
SHIFT
SET-UP
Read these instructions
carefully before programming
your remote control!
MAKE SEARCH PROGRAMMING MODE
A
1.Make sure that the TV is ON.
2.In the code book enclosed, look for
the make of your TV and make a note
of the code indicated at the side
(e.g. Philips 001) or the code for the
make indicated by the arrow.
3.Hold down the SHIFT and ON/OFF
buttons together until the light
indicator at the top starts to flash
indicating that the remote control is
programming.
4.Release the buttons,
within 15 seconds, enter the make
code previously identified (e.g. 001).
The light indicator flashes
more quickly to indicate
that the remote control
is ready for the search.
5.Point the remote control at the TV.
Press and release one of
the most frequently-used
keys several times STOPPING
when the appliance responds
correctly to the command.
6.When the TV responds correctly,
press SHIFT to confirm.
Three flashes indicate that the
operation has been completed
correctly.
Additional check
Check that some of the other functions
used on your original remote control are
working correctly. If the commands
function incorrectly or erratically, you
have probably entered a code for a
similar but different remote control.
In this case, repeat the search
procedure from point 3.
Identify and take note of the TV
code which you have searched for
following the code noting procedure
(see “NOTING THE PROGRAMMED
CODE” section).
0
0
1
SHIFT
NOTE : THE LIGHT INDICATOR
STOPS FLASHING
The remote control leaves the
programming mode and the light
indicator stops flashing:
•if no buttons are pressed for 15
seconds
•if an invalid make code is entered
•if the code search list is completed.
In this case, go back to point 3 or
switch to programming mode C.
FITTING THE BATTERIES
Before programming and using the remote control, fit the batteries.
The remote control requires 2 new AAA/LR03 alkaline batteries.
Insert the batteries as shown.
•The batteries must be changed once a year.
•Change the batteries if the light indicator starts to
flash during use, this indicates that the batteries are
low and should be changed.
•When you remove the batteries, fit the new ones
within 5 minutes or you may have to reprogram your
remote control.
•Make a note of the codes for your TV on the
adhesive label inside the battery cover. This note will
be handy if you have to reprogram your control.
To program the Facile remote
control, follow the indications
in section A , Bor C.
Additional check
Check that some of the other
functions used on your original remote
control are working correctly.
If the commands function incorrectly
or erratically, you have probably
entered a code for a similar but
different remote control.
In this case, repeat the search
procedure from point 2.
1.Make sure that the TV is ON.
2.Hold down the SHIFT
and ON/OFF buttons together
until the light indicator at the
top starts to flash indicating
that the remote control is
programming.
3.Release the buttons.
Within 15 seconds,
enter the code 000.
The light indicator flashes more
quickly to indicate that the remote
control is ready for the search.
4.Point the remote control at the TV.
Press and release one of the
most frequently used keys
several times STOPPING when
the appliance responds correctly
to the command.
5.When the TV responds correctly,
press SHIFT to confirm.
Three flashes indicate that
the operation has been
completed correctly.
Identify and make a note of the
code which you have searched
for following the code noting procedure
(see “NOTING THE PROGRAMMED
CODE” section).
NOTE : THE LIGHT INDICATOR
STOPS FLASHING
The remote control leaves the
programming mode and the light
indicator stops flashing:
•if no buttons are pressed
for 15 seconds
•if the code search list is completed.
1.Make sure that the TV is ON.
2.In the code book enclosed,
look for the make of your TV
and make a note of the first
code indicated BENEATH
the make previously identified
(e.g. Philips 103).
3.Hold down the SHIFT
and ON/OFF buttons together
until the light indicator at the top
starts to flash indicating that the
remote control is programming.
4.Release the buttons.
Within 15 seconds, enter the
code previously identified
(e.g. 103). Three flashes indicate
that the code has been saved
correctly. If not, try the code entry
procedure again from point 3.
Additional check
Point the remote control at the TV.
Check that the appliance responds
correctly to the commands sent.
If there is no response or the appliance
only responds partially or incorrectly,
it is probable that you have used
the wrong code. In this case, try the
procedure again from point 3.
This time, however, use the
NEXT CODE in the list (e.g. 111).
Make a note of the TV code
used to program the remote control
on the adhesive label supplied;
stick the label inside the battery cover,
for rapid consultation.
NOTE : THE LIGHT INDICATOR
STOPS FLASHING
The remote control leaves the
programming mode and the light indicator
stops flashing:
•if no buttons are pressed
for 15 seconds.
•if an invalid make code is entered.
DIRECT CODE ENTRY
B
1
0
3
GLOBAL SEARCH REMOTE CONTROL PROGRAMMING
C
This operation may take up to 30 minutes.
SHIFT
0
0
0
SHIFT
SHIFT
Count the number of flashes for
each code number.
For example, for the code 306, the
button flashes three, zero and six
times to give:
= 3
= 0
= 6
4.Note this code on the label
inside the battery cover,
for rapid consultation.
NOTING THE PROGRAMMED CODE
To find the code for your remote control:
1.Hold down the SHIFT and ON/OFF
buttons together until the light
indicator at the top starts to flash.
2.Release the SHIFT and ON/OFF
buttons and then press and release
the 1-/-- button.
3.After a few seconds, the light
indicator communicates the
code you are looking for by flashing
the three numbers separately.
USING THE ADDITIONAL COMMANDS WHICH DO NOT
APPEAR ON THE KEYPAD
Although not indicated on the keypad, some buttons can be used for
additional commands.
1.Use your Facile remote control to find them by pressing the following buttons one by one:
2.The most frequently used additional commands like MENU SCROLL –COLOUR-
BRIGHTNESS and NORMALISATION are located as follows:
normalisation
OK
1-/--
SHIFT
Always write down the 3-digit code for your remote control on the label
inside the battery cover after running the search and saving the code.
This may be useful if you need to reprogram your remote control in the
event of accidental cancellation or when you change used batteries.
If you forget to write down the code or use the remote control programming
procedures Aor C... don’t worry!
menu (up) +
menu (down) +
menu (right) +
menu (left) +
P
+
P
-
+
-
P
+
P
-
+
-
SHIFT
SHIFT
SHIFT
SHIFT
SHIFT
SHIFT
SHIFT
SHIFT
menu (up)
menu (down)
menu (right)
menu (left)
brightness (-) red
brightness (+) green
color (-) yellow
color (+) blue
brightness (-) + red
brightness (+) + green
color (-) + yellow
color (+) + blue
1-/--
2-
MENU
OK AV
COLOURED
BUTTONS
NOTE :
You cannot use the additional commands unless these were already available on your
original remote control.
REV RIV TUPO CANCEL –+–+–+
TP OFF TP ON FULL EXP EXP ALTO
TIME ORA MEM F MEM TOT TOP BOT I-II
XXX *MENU MENU ●015 014 014 ●015 AV 027 028 027
MIX 10 11
030 058 059
Original remote control / GumBody
additional functions symbols or numbers
▼
▼▼
▼
▼
▼
■❙❙
▼
▼
..
▼ ▼
▼ ▼
3.FOR THE LESSER-USED FUNCTIONS, refer to the code book appendix.
Find the symbol table corresponding to the code you saved to program the remote control.
Locate the additional function you require and note down the symbol or number which
appears below it. EXAMPLE: XXX CODE TABLE
There are 4 ways to enable the additional commands:
A - TV function example:
(a – CANCEL ORA)
A symbol appears beneath the function.
a) the symbol is on your remote control.
(b - brightness +)
b) the symbol is not on your remote control. Find it as indicated
in the drawing. Every symbol is allocated a colour button.
Press the button to transmit the function to the TV. The commands stops when you
release the button.
B - TV function example:
(a – FULL TOT)
A symbol against a grey background appears beneath the
function.
a) the symbol is on your remote control.
(b - sleep)
b) the symbol is not on your remote control. Find it as indicated
in the drawing.
Press SHIFT and the button at the same time. The corresponding function is transmitted to the TV
and stops when you release the button.
C – TV function example:
EXP BOT
A number appears beneath the function (028).
Press and hold down SHIFT.
Type in the number, holding down the last digit (8).
The function is transmitted to the TV and stops when you release
the two buttons (SHIFT+ 8).
D – TV function example:
contrast +
Both a symbol and a number are displayed beneath the function.
You can apply the command using either the symbol or the
number.
If the symbol is not on the remote control, use the number
following the example Cabove.
INFO-LINE
If you have any queries about Facile:
•read this booklet carefully, this will help you to solve almost all problems
•consult our Internet site www.meliconi.it to answer all your queries more easily and quickly.
WARRANTY: 2 years
Tampering or improper product use will void this
guarantee.
Type of remote control Facile
Remote control model GumBody
Purchase date
Agent’s stamp
TROUBLESHOOTING
PROBLEM
The TV does not respond and the light
indicator does not light up when you
press a button.
The TV or VCR does not respond but the
light indicator lights up.
The light indicator flashes.
The remote control commands are not all
working correcting.
The code for your TV make is not in the
Code Book.
SOLUTION
Try some of the other frequently used buttons.
If the problem persists, check that the
batteries are fitted correctly.
If necessary replace them
with 2 new 1.5 V AAA/LR03
alkaline batteries.
Check that the batteries are new
and that the remote control is
pointing at the appliance without any
obstacles in the way. If required,
reset the remote control code,
following the programming
procedure Aor Bor C.
The batteries are low. Change them.
You may have used the wrong
code. Reset the remote control code,
following the programming
procedure Aor Bor C.
Set the remote control code,
following the global search
programming procedure C.
Table des matières
Autres manuels MELICONI Télécommande
MELICONI
MELICONI GumBody Universal 5 web Manuel utilisateur
MELICONI
MELICONI TLC05 Manuel utilisateur
MELICONI
MELICONI GUMBODY UNIVERSAL 3-300 Manuel utilisateur
MELICONI
MELICONI LOGIC12 Manuel utilisateur
MELICONI
MELICONI Personal 4+ Manuel utilisateur
MELICONI
MELICONI SPEEDY 110 Manuel utilisateur
MELICONI
MELICONI TLC03+ Manuel utilisateur
MELICONI
MELICONI FULLY 8 Manuel utilisateur
MELICONI
MELICONI TLC02 Manuel utilisateur
MELICONI
MELICONI GUMBODY UNIVERSAL 5 SMART Manuel utilisateur
MELICONI
MELICONI pratico 6 Manuel utilisateur
MELICONI
MELICONI TLC04 Manuel utilisateur
MELICONI
MELICONI pratico 6 Manuel d'installation et d'exploitation
MELICONI
MELICONI Personal 2 plus Manuel utilisateur
MELICONI
MELICONI Fully 8.1 Manuel utilisateur
MELICONI
MELICONI Speedy Mode d'emploi
MELICONI
MELICONI GumBody DIGITAL 2 SMART Manuel utilisateur
MELICONI
MELICONI CONTROL 4 Plus Manuel utilisateur
MELICONI
MELICONI Speedy 210 combo Manuel utilisateur
MELICONI
MELICONI Colibri 2 Manuel utilisateur
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
