MELICONI Speedy 100 plus Manuel utilisateur
5
Thank you for choosing MELICONI.
This simplified universal remote control contains all the main functions of most TV remote controls of
the brands listed on the back.
Before programming and using the remote control, fit the batteries.
Keep your Instructions and Code Booklet for future reference.
USING THE KEYS AND FUNCTIONS
FITTING THE BATTERIES
GB
SET-UP
Read these instructions carefully before programming your remote control!
To command your appliances, you must program your Speedy 100 plus as described in
paragraphs Aor Bbelow.
Visit out Internet site www.meliconi.com for interactive instructions for easy and fast remote
control programming.
Teletext keys:
to access Teletext
close Teletext and return to
normal viewing
Teletext page hold function
Light indicator.
P+ to select the next program or
to turn ON your TV.
ON/OFF to turn OFF your TV and, in some
cases, to turn ON your TV.
Control the volume using +/ -.
P- to select the previous program.
Key with additional TV functions.
Number key.
Mute key.
Before programming and using the remote control, fit the batteries.
The remote control requires 2 new AAA/LR03 alkaline batteries. Insert the batteries as shown.
• The batteries must be changed once a year.
• Change the batteries if the light indicator starts to flash during use.
The batteries are low.
• When you remove the batteries, fit the new ones within 5 minutes or
you may have to reprogram your remote control.
• Make a note of the code for your TV on the adhesive label supplied
inside the battery cover. This note will be handy if you have to
reprogram your remote control.
To select an external input terminal.
6
Identify and take note of the TV code which you have searched for following the code noting procedure
(see “PROGRAMMED CODE NOTING” section).
1. Make sure that your TV is ON.
2. In the Code Book, look for your TV brand and make a note of the corresponding TV code indicated to the
side (e.g. Philips 0025). If your TV brand is not listed, apply the global search described in paragraph B.
3. Hold down the and keys together until the light indicator at the top starts to flash indicating that
the remote control is programming.
4. Release the keys, Within 15 seconds, enter the brand code previously identified (e.g. 0025). The light
indicator flashes more quickly to indicate that the remote control is ready for the search.
5. Point the remote control at the TV. Press and release the key slowly several times. Stop when your TV
goes OFF (you may have to press the key dozens of times).
6. When your TV is off, press the key to confirm.
Three long flashes indicate that the operation has been completed correctly.
Additional check
Check that some of the other functions used on your original remote control are working correctly. If the
commands function incorrectly or erratically, you have probably entered a code for a similar but different
remote control. In this case, repeat the search procedure from point 3.
BRAND SEARCH PROGRAMMING MODE
A
NOTE: during the search operation, the light indicator flashes more quickly. The light indicator
stops flashing and the remote control leaves the programming mode in the following cases:
• if no keys are pressed for 12 seconds
• if the code search list is completed. In this case, switch to programming mode B
This operation may take up to an hour.
1. Make sure that the TV is ON.
2. Hold down the and keys together until the light indicator at the top starts to flash indicating that
the remote control is programming.
3. Release the keys. Within 15 seconds, enter the code 0000.
The light indicator flashes more quickly to indicate that the remote control is ready for the search.
4. Point the remote control at the TV. Press and release the key slowly several times. Stop when your TV
goes OFF (you may have to press the key over a hundred times).
5. When your TV is off, press the key to confirm. Three long flashes indicate that the operation has
been completed correctly.
Additional check
Check that some of the other functions used on your original remote control are working correctly.
If the commands function incorrectly or erratically, you have probably entered a code for a similar but
different remote control.
In this case, repeat the search procedure from point 2.
GLOBAL SEARCH REMOTE CONTROL PROGRAMMING
B
AV
AV
7
Identify and take note of the code which you have searched for following the code noting procedure
(see “PROGRAMMED CODE NOTING” section).
NOTE: during the search operation, the light indicator flashes more quickly. The light indicator
stops flashing and the remote control leaves the programming mode in the following cases:
• if no keys are pressed for 12 seconds.
• if the code search list is completed. In this case, visit www.meliconi.com
Always write down the 3-digit code for your remote control on the label inside the battery cover
after running the search and saving the code.
This may be useful if you need to reprogram your remote control in the event of accidental
cancellation or when you change used batteries.
To find the code for your remote control:
1. Hold down the and keys together until the light indicator at the top starts to flash indicating that
the remote control is programming.
2. Release the and keys. Then enter the code you noted down previously. Three flashes indicate
that the code has been saved correctly. If not, try the code entry procedure again from point 1.
PROGRAMMED CODE NOTING
1. Hold down the and keys until the light indicator at the top starts to flash.
2. Release the and keys and then press the key.
3. After a few seconds, the light indicator communicates the code you are looking for by flashing the three
numbers separately. Count the number of flashes for each code number. For example, for the code 1306,
the key flashes three, zero and six times to give:
= 1
= 3
= 0
= 6
4. Note this code on the label inside the battery cover, for rapid consultation.
1
-/--
RE-PROGRAMMING YOUR REMOTE CONTROL BY ENTERING THE CODE NOTED DOWN
8
TROUBLESHOOTING
PROBLEM
The TV does not respond and the light
indicator does not light up when you press a
key.
The TV or VCR does not respond but the
light indicator does light up.
The TV does not respond and the light
indicator flashes.
The remote control commands are not all
working correcting.
The code for your TV brand is not in the
Code Book.
SOLUTION
Check that the batteries are fitted correctly. If
necessary, replace them with 2 new 1.5 V
AAA/LR03 alkaline batteries.
Check that the batteries are new and that the
remote control is pointing at the appliance
without any obstacles in the way. If required,
reset the remote control code, following the
programming procedure A or B.
The batteries are low. Change them.
You may have used the wrong code. Reset
the remote control code, following the
programming procedure Aor B .
Set the remote control code, following the
global search programming procedure B.
WARRANTY: 2 years
The warranty ceases to be valid if the product is tampered with or
used incorrectly.
Remote control model Speedy 100 plus
Purchase date
If you have any queries about Speedy 100 plus:
•read this booklet carefully– this will help you to solve almost all problems
•consult our Internet site www.meliconi.com to answer all your queries more easily and quickly.
Agent's stamp
INFO LINE
Autres manuels MELICONI Télécommande
MELICONI
MELICONI GumBody Universal 5 web Manuel utilisateur
MELICONI
MELICONI GUMBODY FACILE SMART Manuel utilisateur
MELICONI
MELICONI CONTROL 2 Simple Manuel utilisateur
MELICONI
MELICONI pratico 6 Manuel utilisateur
MELICONI
MELICONI Speedy Mode d'emploi
MELICONI
MELICONI TLC02 Manuel utilisateur
MELICONI
MELICONI Personal 6+ Manuel utilisateur
MELICONI
MELICONI MYCRO Manuel utilisateur
MELICONI
MELICONI FACILE Manuel utilisateur
MELICONI
MELICONI TLC04 Manuel utilisateur
MELICONI
MELICONI GumBody Personal 1 Manuel utilisateur
MELICONI
MELICONI personal 4 Manuel utilisateur
MELICONI
MELICONI Speedy 210 combo Manuel utilisateur
MELICONI
MELICONI Personal 3 plus Manuel d'installation et d'exploitation
MELICONI
MELICONI Smart4 Manuel utilisateur
MELICONI
MELICONI TLC03+ Manuel utilisateur
MELICONI
MELICONI TLC05 Manuel utilisateur
MELICONI
MELICONI CONTROL 4 Plus Manuel utilisateur
MELICONI
MELICONI Personal 1+ Manuel utilisateur
MELICONI
MELICONI Algo 2.1 Manuel utilisateur
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
