MELICONI EASY 300 Manuel utilisateur
EASY 300
Thank you for choosing a Meliconi remote control.
The EASY 300 remote control is designed to command a SONY digital television sets.
The MELICONI remote control reproduces infrared signals corresponding to the original; the functions that operate in radio
frequency (e.g. voice commands and pointers) are not supported.
The remote control has a permanent memory, so it does not lose its settings even if there are no batteries in it.
The remote control requires 2 new 1.5V AAA/LR03 alkaline batteries, not included in the
package. Insert with the correct polarity as shown in figure.
DO NOT use rechargeable batteries.
BATTERIES TEST: Press and hold the GUIDE button and check that the LED blinks
continuously until the button is released. If the light is off, the inserted batteries are low, therefore
they need replacement.
If problems are found to command the TV, or some functions do not produce the desired effect, please proceed as follow:
• Press and hold for at least 8 seconds the 2numeric button.
•Three final flashes indicate that the operation has been completed successfully.
• Now check if the remote control act properly.
If not, again repeat the procedure using the 3numeric button.
To restore the remote control and return to the initial condition, perform the procedure using the 1button.
To consult the key correspondence table between the Meliconi remote control and the functions of the original remote
control, go to www.cme.it , select the remote control model and click on "KEY CORRESPONDENCE TABLE".
ACTIVATION OF REMOTE CONTROL
Do not leave exhausted batteries inserted, as liquid may leak and damage the remote control
INSERTING THE BATTERIES
SAFETY WARNINGS
The remote control and batteries should not be exposed to excessive heat such as sunlight, fire
or the like.
The product is not a toy. Keep out of reach of children or domestic animals.
This remote control, after inserting the batteries, is normally ready for use as it is already set at the
factory with a specific code.
If problems are found to command the TV, or some functions do not produce the desired effect, to follow the instructions
to the chapter ACTIVATION OF REMOTE CONTROL.
Keep this booklet for future reference
Remote control for TV sets SONY ready to use
The EASY 300 remote control is equipped with Learn technology that can acquire and memorise signals from other infrared
remote controls. This feature is particularly useful in several cases.
➢To add or change a function connected to a button on the MELICONI remote control.
Having activated the remote control and checked it is working correctly, you may need to add or replace a function on one
of the MELICONI remote control buttons with another function you consider to be handier or more frequently used.
➢Assign some functions to some buttons to control other devices (example: volume +/- SOUNDBAR).
The EASY 300 remote control can learn up to a maximum of 16 signals coming from various original remote controls and
connect at will to the desired buttons.
Signals can also be learnt and set on all the buttons on the MELICONI remote control, except the button. Obviously the
preset functions are lost, but they can be restored using the procedure RESET THE REMOTE CONTROL.
The Learn operation can be repeated numerous times, and the signals captured are kept in the memory even if the batteries
are removed or go flat.
●POSITIONING THE REMOTE CONTROLS CORRECTLY.
•Check that the batteries in both remote controls (the original
and the MELICONI remote) are fully charged; if semi-charged
batteries are used the signal acquisition procedure may prove
difficult or fail completely.
•Position the original remote control in front of the MELICONI
remote control so the areas which emit the infrared signals are
opposite each other at a distance of approximately 2 cm.
●CAPTURING SIGNALS.
1. On the MELICONI remote control press and hold the and buttons until the LED lights up; release.
2. on the MELICONI remote control press the desired button to match the function to learn.
3. While the LED is flashing, press the button on the original remote to be captured, hold it down until the LED goes out and
then release it.
4. Three final flashes indicate that the operation has been completed successfully.
5. To capture other signals to connect to other buttons, repeat the procedure from point 2.
6. To end the procedure, press the button.
Reached the number of records available, the dedicated memory becomes full, preventing further use.
To free memory use one of the following procedures in relation to the data that you want to delete:
• Use LEARN FUNCTION on a previously learnt key (overwrite key)
• RESET THE REMOTE CONTROL
If necessary it is possible to completely reset the remote control and bring it back to the initial conditions.
WARNING : All user settings, included keys learnt by LEARN FUNCTION, will be lost. Operate as follows:
•On the MELICONI remote control press and hold the e .
•Two final flashes indicate that the operation has been completed successfully.
RESET THE REMOTE CONTROL
LEARN FUNCTION
IMPORTANT! To obtain technical assistance, it is essential to indicate the BRAND and MODEL of the appliance you intend
to control and the name of the MELICONI remote control you are using.
●IF THE REMOTE CONTROL IS NEW AND YOU CAN NOT MAKE IT WORK
It is possible that the code set in the remote control is incorrect for the device that you want to control. Check that you have
carried out all the settings procedures correctly. If necessary repeat them, following all the steps indicated carefully.
Consult the website www.cme.it or contact the ASSISTANCE.
●IF THE REMOTE CONTROL IS NO LONGER ABLE TO CONTROL THE DEVICE
Disconnect the device from the electric socket and leave it without power for a few minutes; switch the device on again.
Remove the batteries from the remote control, press the ON/OFF button twice and insert NEW batteries.
Make sure that the remote control is pointing at the device without any obstacles between them.
If necessary try to the RESET THE REMOTE CONTROL and carry out a new activation.
●IF SOME FUNCTIONS ARE NOT AVAILABLE ON THE REMOTE CONTROL
If some of the MAIN functions are not available, you are probably using an incorrect code. Find and set a more suitable code
as described in the ACTIVATION OF REMOTE CONTROL chapter.
●HOW TO CHECK IF THE REMOTE CONTROL SENDS INFRARED SIGNALS
The human eye is not able to detect infrared signals; use a camera (even that of the mobile phone).
Aim the infrared LED located in front of the remote control (not the red LED above) and press and hold on the remote control
the button.
If you see through the camera, the LED light with short white / light blue flashes means that the remote control works and
emits infrared.
WARRANTY: 2 year Always keep your sales receipt as proof of the validity of the product’s warranty. The warranty is
voided if the product is tampered with or used improperly.
Meliconi SpA, Via Minghetti 10 - 40057 Cadriano di Granarolo Emilia, (BO) Italy
The symbol showing a wheelie bin with a cross through it which appears on the device indicates that at the
end of its useful life the product must be collected separately from other waste. Therefore, at the end of the
device’s life, you must take it to appropriate centres for the differentiated collection of electrical and electronic
waste, or return it to the retailer when purchasing a new device of equivalent type. Suitable differentiated
collection to allow subsequent recycling of the decommissioned device, with environmentally-compatible
treatment and disposal, help to prevent any negative effects on the environment and health and to promote
the recycling of the materials of which the device is made.
ATTENTION!
Most problems are caused by using insufficiently charged batteries.
We recommend checking and replace them as shown in the INSERTING THE BATTERIES chapter.
TROUBLESHOOTING (F.A.Q.)
ASSISTANCE
CAUTION: Batteries must not be disassembled, thrown into fire or released into the environment. Improper
use can cause damage to the environment and health. The symbol of the bins, indicating that the batteries
should be disposed of according to current regulations; inquire on collection of spent batteries and
accumulators in force in your country.
Table des matières
Autres manuels MELICONI Télécommande
MELICONI
MELICONI Universal 2 Manuel utilisateur
MELICONI
MELICONI CONTROL 5-500 PLUS Manuel utilisateur
MELICONI
MELICONI TLC03 Manuel utilisateur
MELICONI
MELICONI FACILE Manuel utilisateur
MELICONI
MELICONI Control 5 500 PLUS Manuel utilisateur
MELICONI
MELICONI Pratico 2 Manuel utilisateur
MELICONI
MELICONI TLC02 Manuel utilisateur
MELICONI
MELICONI TLC05 Manuel utilisateur
MELICONI
MELICONI Facile 5.1 LED Manuel utilisateur
MELICONI
MELICONI Speedy 210 combo Manuel utilisateur
MELICONI
MELICONI Algo 2.1 Manuel utilisateur
MELICONI
MELICONI Personal 3 plus Manuel d'installation et d'exploitation
MELICONI
MELICONI GumBody Universal 5 web Manuel utilisateur
MELICONI
MELICONI Control TV.1 Manuel utilisateur
MELICONI
MELICONI Personal 4+ Manuel utilisateur
MELICONI
MELICONI personal 4 Manuel utilisateur
MELICONI
MELICONI MYCRO Manuel utilisateur
MELICONI
MELICONI pratico 6 Manuel utilisateur
MELICONI
MELICONI Smart4 Manuel utilisateur
MELICONI
MELICONI CONTROL 4 Plus Manuel utilisateur
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
