MegaLite Axis QD7 Manuel utilisateur

USER MANUAL

Table of Contents

Safety Information……………………………………...………………3

Specifications………………………………………...…………………4

Main Power Connection…………………………...…………………..5

DMX-512 Connection……………………………..…………………...5

Rigging the Fixture……………………………….…………………….6

Main Control Menu……………..…………………………………..….6

DMX Profile.................................................................................... 8

Cleaning & Maintenance...............................................................13

Parts List.......................................................................................13

Check that the unit has not been damaged during transport

Protection Against Fire

1. Maintain a minimum of 1 foot distance from any type of flame.

3. Replace fuse only with the specified type and rating.

4. Do Not install the unit to close to a heat source.

5. Make sure cable are properly secured away from unit movement.

6. Maximum surface operating temperature 104º.

Protection Against Fire

1. Disconnect power before lamp replacement or servicing.

2. For connection to main power supply proceed to page 6.

3. This unit must be earthed. (electronically grounded)

4. Do not expose unit to rain or moisture.

Protection Against Mechanical Hazards

1. Use safety chain when hanging unit.

2. Use quality clamps or bolts when positioning unit

3. Do not open unit risk of electrical shock.

Specifications

Part Numbers

Fixture Lamp Flight Case

1125- AXIS QD7 LOSRAM–12W RGBWLED P-1125 DUALCASE

Mechanical Specifications

Fixture Packaged for Shipping

Size: 10.5” x 96.5 x 12.5”

Weight: 12 lb

Pan: 540° Tilt: 270°

DMX Connectors: 3-pin and 5-pin XLR connectors

Thermal: Maximum ambient temperature 100° F

Maximum surface temperature 130° F

Fastening System: 1 Removable mount

Electrical Specifications

Power supply: Auto Switch100V-240V 50/60 HZ

Power consumption: Amps 1.45

Watts 106

Ballast: Electronic

LAMP: 7X 12W RGBW LED’s

10 ” ( with handles )

3.5 ”

9”

10.75 ”

LED Control: Individual control of each LED

Shutter: Electronic Lamp strobe of lamp 18 flash per second

Electromechanical Effects

10.5 ”

Size: 12.5” x 9” x 13.5”

Weight: 13.5lb

6.5 ”

3.75 ”

Main Power Connection

Caution!

1. Do not connect fixture to a dimmer system.

2. This unit must be earthed. (electronically grounded)

3. Replace fuse only with the specified type and rating.

The occupation of the connection-cable is as follows:

DMX-512 Connection

This device is equipped with a auto switching power supply that will allow you to work from 100V-240V 50/60Hz

The fixture is equipped with 3 pin and 5 pin XLR Sockets for DMX input and output. The sockets are wired in parallel.

Only use a shielded twisted pair cable designed for RS-485 and 3 pin or 5 pin XLR plugs and connectors in order to con-

nect the controller with the fixture or the fixture with another.

Caution!

At the last fixture the DMX signal needs to be terminated with a terminator. Solder a

120 Ohm resistor between the (-) and the (+) signal into a 3 pin or 5 pin XLR plug

and plug it in to the last fixture on the signal run. Pre-manufactured terminator plugs

are available for purchase from your Mega-Lite dealer (HOS-DMXT).

Cable (USA) Cable (EU) Pin 110V

Black Brown

White

Green

Light Blue

Yellow/Green

Live

Neutral

Ground

220V

110V

Connec-

220V

Connec-

DMX—input DMX—output

1. Shield

2. Signal (-)

3. Signal (+)

4. N/A

5. N/A

Rigging the fixture

Caution!

1. The installations must be carried out by an authorized dealer or trained professional.

2. Unit may cause severe injures if you have doubts concerning the safety do not install.

3. Unit is to be 24inches away from flammable materials (decoration material)

4. Use high quality installation equipment to hang unit.

When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experi-

ence including but not limited to calculating working loads, material being used and periodic safety inspections. If you

lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.

When rigging the unit always be secured with a secondary safety attachment. The installation location of the projector

has got to be built in the way that it can hold 10 times the weight for 1 hour with out any damage. Installation should be

checked at least one time a year by a skilled person.

Main Control

The control board on the fixture base is your interface to access and

control all the functions on the unit. Its LED display gives you a code

view of the options and functions. The following will explain each func-

tion and its options.

DMX

MASTER

SLAVE

SOUND

MENU ▲ ▼ ENTER 5718 Kenwick St

San Antonio TX 78238

800-460-MEGA

www.mega-lite.com

—DMX512—

ADDR:001

This function allows you to set your DMX Start Channel. First make sure you

have a proper DMX connection from your controller using the 3 or 5 pin XLR con-

nection. If there is no DMX connection the display will flash and read No DMX

ADDR:001. If there is proper DMX connection the display will be solid on and will

read DMX 515, there will also be a Green indicator light that will turn on.

To Set the DMX Start Channel press the ▲ then press Enter. Use the ▲ or ▼ to

select the desired DMX Start Channel and press Enter to confirm your setting.

>Work Mod

DMX 512

DMX 512= This mode will allow you to operate the fixture with a DMX con-

troller

Auto= This Function slows the unit to run a preset program

Sound= On Sound Mode the fixture will trigger the preset program with the

ambient audio sensitivity.

To Set the Desired operational mode press the ▲ then Press Enter. Use the ▲

or ▼ to select the desired DMX Start Channel and press Enter to confirm your

setting.

>Chan Mod

17CH

To set the desired operational channel mode press Enter. Use the ▲ or ▼ to

select the desired DMX profile operational mode from 6,17 or 37 and press Enter

to confirm your setting.

Note: Operational mode are located on Page 8 of the manual.

>Tool

DimmMod

>DimmMod

Smooth

This function will give you access to the Display Control press Enter. Use the ▲

or ▼ to select the desired display operational Mode from turn off in 60 second or

stay On, press Enter to confirm your setting.

>Display

60S

This function will give you access to the LED Dimming curve press Enter. Use

the ▲ or ▼ to select the LED dimming operational Mode from fast or smoth,

press Enter to confirm your setting.

>PT Sett

Xrevise

If you wish to fine adjust your Pan extreme position press Enter. Use the ▲ or

▼ to select the desired Pan extreme position, press Enter to confirm your setting.

>Xrevise

000

If you wish to fine adjust your Tilt extreme position press Enter. Use the ▲ or ▼

to select the desired Tilt extreme position, press Enter to confirm your setting.

>Yrevise

000

To invert the Pan position press Enter. Use the ▲ or ▼ for yes or no to invert,

press Enter to confirm your setting.

>Xreverse

To invert the Tilt position press Enter. Use the ▲ or ▼ for yes or no to invert,

press Enter to confirm your setting.

>Xreverse

To adjust the speed of Pan & Tilt position press Enter. Use the ▲ or ▼ for slow,

normal and fast, press Enter to confirm your setting.

>XYspeed

fast

To adjust press Enter. Use the ▲ or ▼ for Yes or No, press Enter to confirm

your setting.

>XYfbsti

yes

>Control

CH01

To access the control channels via display press Enter. Use the ▲ or ▼ to se-

lect the desired DMX Channel press Enter to access that function use the ▲ or

▼ to adjust the channel.

Note: Operational Channels are located on Page 10 of the manual.

>DmxLive

CH1

To view the status of every channel via display press Enter. Use the ▲ or ▼ to

select the desired DMX Channel press Enter to view the channel status.

>RGBWhit

WhitB

To adjust the white color balance Press Enter

If you wish to fine-tune the white color balance press Enter select On or Off press

Enter to confirm your setting.

>WhiteSW

To fine adjust the Red press Enter. Use the ▲ or ▼ to select the desired maxi-

mum intensity of the Red LED, press Enter to confirm your setting.

>WhitR

255

To fine adjust the Green press Enter. Use the ▲ or ▼ to select the desired max-

imum intensity of the Green LED, press Enter to confirm your setting.

>WhitG

255

To fine adjust the Blue press Enter. Use the ▲ or ▼ to select the desired maxi-

mum intensity of the Blue LED, press Enter to confirm your setting.

>WhitB

255

>Info

Version

Press Enter to see the current software version

>Reset

To reset the fixture press Enter. Use the ▲ or ▼ for Yes or No press Enter to

confirm your setting.

DMX Profile

Axis QD7 6 Ch Mode 1

1Pan Pan Course 0-255

2Tilt Tilt Course 0-255

3LED Color Red 0-255

4LED Color Green 0-255

5LED Color Blue 0-255

6LED Color White 0-255

Axis QD7 17 Ch Mode 2

DMX Channel Function Description Value

1Pan Pan Course 0-255

2Pan Fine Pan Fine 0-255

3Tilt Tilt Course 0-255

4Tilt Fine Tilt fine 0-255

Fast 0-84

5Pan/Tilt Speed Mid 85-170

Slow 171-255

6LED Color Red 0-255

7LED Color Green 0-255

8LED Color Blue 0-255

9LED Color White 0-255

Closed 0-31

Strobe (slow to fast) 32-95

10 Shutter Pulse (slow to fast) 96-159

Random Strobe (slow to fast) 160-223

Open 224-255

11 Dimmer Dimmer off to full 0-255

12 Color Fade Color Fade (slow to fast) 0-255

No Function 0-10

White 2700K 11-20

White 3200K 21-30

White 4300K 31-40

White 5600K 41-50

White 6500K 51-60

13 Color Preset White 8000K 61-70

Blue 1-Red 2,3,4,5,6,7 71-100

Blue 1-Green 2,3,4,5,6,7 101-130

Green1-Red 2,3,4,5,6,7 131-160

Red1-Blue 2,3,4,5,6,7 161-190

Green1-Blue 2,3,4,5,6,7 191-220

Red1-Green 2,3,4,5,6,7 221-255

No Function 0-10

Red Strobe (slow to fast) 11-20

Green Strobe (slow to fast) 21-30

Blue Strobe (slow to fast) 31-40

White Strobe (slow to fast) 41-50

All Strobe Chase (slow to fast) 51-60

14 Strobe Macro Random Strobe (slow to fast) 61-70

No Function 71-100

Red Strobe 2,3,4,5,6,7,(slow to fast) 101-130

Green Strobe 2,3,4,5,6,7,(slow to fast) 131-160

Blue Strobe 2,3,4,5,6,7,(slow to fast) 161-190

White Strobe 2,3,4,5,6,7,(slow to fast) 191-220

All Strobe 1,2,3,4,5,6,7,(slow to fast) 221-255

No Function 0-10

Color Chase Macro 1 11-40

Color Chase Macro 2 41-70

Color Chase Macro 3 71-100

15 Macros Color Chase Macro 4 101-130

Color Chase Macro 5 131-160

Color Chase Macro 6 161-190

Color Chase Macro 7 191-220

Color Chase Macro 8 221-255

16 Macros Speed Macro Speed (slow to fast) 0-255

No Function 0-79

All Motor Reset 80-99

17 Control Demo Program 1 100-150

Demo Program 2 151-200

Demo Program 3 201-250

No Function 251-255

Axis QD7 37 Ch Mode 3

Closed 0-19

Open 20-49

Strobe (fast to slow) 50-64

Open 65-69

Open Pulse (fast to slow) 70-84

Open 85-89

Closing Pulse (fast to slow) 90-104

Open 105-109

Random Strobe (fast to slow) 110-124

Open 125-129

Random Open Pulse (fast to slow) 130-144

1Shutter Open 145-149

Random Closing Pulse (fast to slow) 150-164

Open 165-169

Burst Pulse (fast to slow) 170-184

Open 185-189

Random Burst Pulse (fast to slow) 190-204

Open 205-209

Wave Strobe (fast to slow) 210-224

Open 225-229

Burst Strobe (fast to slow) 230-244

Open 245-255

2Dimmer Dimmer 0-244

Open 245-255

3Pan Pan 0-255

4Pan Fine Pan Fine 0-255

5Tilt Tilt 0-255

6Tilt Fine Tilt Fine 0-255

7Pan/Tilt Speed Pan/ Tilt Speed (fast to slow) 0-255

Lamp Control 0-9

8Control Fixture Reset 10-14

Lamp Control 15-248

Single LED Control 249-255

Table des matières

Autres manuels MegaLite Équipement d'éclairage

MegaLite

MegaLite cobra 1500 Manuel utilisateur

MegaLite

MegaLite N-E Color FX9 Manuel utilisateur

MegaLite

MegaLite Deco Vintage Scoop Q32 Manuel utilisateur

MegaLite

MegaLite outshine ww100 Manuel utilisateur

MegaLite

MegaLite TUFFBABYVW-42 Manuel utilisateur

MegaLite

MegaLite 44010- Vazt UV50 Manuel utilisateur

MegaLite

MegaLite DECO Cove Q18 Manuel utilisateur

MegaLite

MegaLite Drama LED Q170 Manuel utilisateur

MegaLite

MegaLite Drama Profile VW2 Manuel utilisateur

MegaLite

MegaLite HELIUS M Manuel utilisateur

MegaLite

MegaLite Framebot 600 Manuel utilisateur

MegaLite

MegaLite XWITCH Manuel utilisateur

MegaLite

MegaLite N-E Color FX18 Manuel utilisateur

MegaLite

MegaLite DECO TENTACLE Manuel utilisateur

MegaLite

MegaLite Axis LED Manuel utilisateur

MegaLite

MegaLite EB1 Manuel utilisateur

MegaLite

MegaLite Linebot Q480 Manuel utilisateur

MegaLite

MegaLite AXIS 250 Manuel utilisateur

MegaLite

MegaLite Pro Color Cannon 3000 Manuel utilisateur

MegaLite

MegaLite DECO Driver CV4 Manuel utilisateur

MegaLite

MegaLite baby color Q70 IR Manuel utilisateur

MegaLite

MegaLite Pro Color Strip Manuel utilisateur

MegaLite

MegaLite Deco Flex C Manuel utilisateur

MegaLite

MegaLite IDOL-LITE P24 Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur