M-system R80FST4NJ Manuel utilisateur

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7029 P. 1 / 7

INSTRUCTION MANUAL

DC VOLTAGE / CURRENT INPUT MODULE, 4 points

(4 points, non-isolated, tension clamp terminal block) MODEL

R80FST4NJ

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

DC voltage / current input module.....................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside a panel.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■GENERAL PRECAUTIONS

• Before you remove or mount the unit, turn off the power

supply and output signal for safety.

• DO NOT set the switches while the power is supplied.

The switches are used only for maintenance without the

power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 10 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■POWER UP

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for-

satisfying complete performance described in the data-

sheet.

INSTALLATION

■HOW TO MOUNT THE MODULE ON DIN RAIL

Confirm that the locking clamps of the extension power supply module

are set. Insert the module in parallel to the next one while aligning the

grooves of both modules (A & B in the above figure).

Maintain it perpendicularly to the rail.

More I/O modules can be added in the same manner.

R80FST4NJ

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7029 P. 2 / 7

• Protective Cover

The protective cover is to be attached over the connected I/O module

at the right end.

Align the hooks on the cover with the grooves of the module and slide it

straight until the hooks are latched.

When removing the cover, pull it out while squeezing the hooks inward.

Groove

Hook

■HOW TO UNMOUNT THE MODULE FROM DIN RAIL

Release the locking clamps and pull out straight the module.

Caution !

1) Be careful not to hurt your hand by pointed edges of the internal bus

connector.

2) I/O modules cannot hold tightly on the DIN rail by themselves without

power/network module.

Secure them to the position if necessary by using DIN rail end plates.

• Removing an intermediate module

R80FST4NJ

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7029 P. 3 / 7

COMPONENT IDENTIFICATION

■FRONT VIEW ■RIGHT VIEW

Input Connector

Internal Bus

Connector

Module Address

DIP SW

SW1

Status Indicator LED

Input Status

Indicator LEDs

Input

DIP SW

SW3

■LEFT VIEW

Terminal

DIP SW

RUN

Term

SW2

■STATUS INDICATOR LED / INPUT STATUS INDICATOR LED

LED OPERATION COLOR FUNCTION

RUN

Indicator LED

ON Red Upper communication: Stopping or abnormal

Internal communication: Abnormal

ON Green Upper communication: Normal

Internal communication: Normal

Blink

1 sec. sycle

– Input value error

(Exceeds the upper limit of usable range).

Blink

400 msec. cycle

– Input circuit abnormality (AD converter response failure)

OFF – Upper communication: Stopping or abnormal

Internal communication: Normal

Input Status

Indicator LED

OFF Red Input data in the range

ON Input value error

(Exceeds the upper limit of usable range).

Input circuit abnormality (AD converter response failure)

R80FST4NJ

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7029 P. 4 / 7

■OPERATING MODE SETTING

(*) factory default setting

Note) Be sure to unused SW 1-5 through 1-8 to OFF.

• Module Address Setting

Conﬁgurate the mosule address with DIP Switch.

0 - 15 are available for module address.

MODULE AD-

DRESS

SW1

1234

0(*) OFF OFF OFF OFF

1 ON OFF OFF OFF

2 OFF ON OFF OFF

3 ON ON OFF OFF

4 OFF OFF ON OFF

5 ON OFF ON OFF

6 OFF ON ON OFF

7 ON ON ON OFF

8 OFF OFF OFF ON

9 ON OFF OFF ON

10 OFF ON OFF ON

11 ON ON OFF ON

12 OFF OFF ON ON

13 ON OFF ON ON

14 OFF ON ON ON

15 ON ON ON ON

• Terminator Setting

Terminator SW2

Disabled (*) OFF

Enabled ON

• Input Setting

Input Setting

SW3

1234

Input 1 Input 2 Input 3 Input 4

DC voltage (*) OFF OFF OFF OFF

DC Current ON ON ON ON

R80FST4NJ

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7029 P. 5 / 7

■INPUT CONNECTOR TERMINAL ASSIGNMENT

PIN No. ID FUNCTION

1 Ai1 Input 1 (+)

2 AG1 Input 1 (–)

3 + Excitation supply (+)

4 – Excitation supply (–)

5 Ai2 Input 2 (+)

6 AG2 Input 2 (–)

7 + Excitation supply (+)

8 – Excitation supply (–)

9 Ai3 Input 3 (+)

10 AG3 Input 3 (–)

11 + Excitation supply (+)

12 – Excitation supply (–)

13 Ai4 Input 4 (+)

14 AG4 Input 4 (–)

15 + Excitation supply (+)

16 – Excitation supply (–)

R80FST4NJ

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7029 P. 6 / 7

PC CONFIGURATOR

The following parameters can be set with using PC Conﬁgurator Software (model: R80CFG)

Refer to the users manual for the R80CFG for detailed operation of the software program.

■CHANNEL INDIVIDUAL SETTING

ITEM SETTING RANGE DEFAULT VALUE

Unused setting CH enabled

CH disabled

CH enabled

Input type DC voltage -10 - +10 V DC -10 - +10 V DC

DC current -20 - +20 mA DC

Zero ﬁne adj. -320.00 - +320.00 (%) 0.00 (%)

Gain ﬁne adj. -3.2000 - +3.2000 1.0000

Zero base depends on input types*1-10.000 V

Full base depends on input types*110.000 V

Zero scaling -32,000 - +32,000 0

Full scaling -32,000 - +32,000 10,000

*1. For details, refer to the users manual of R80CFG

■CHANNEL BATCH SETTING

ITEM SETTING RANGE DEFAULT VALUE

Version no. – –

Simulate input Normal input

Simulated data

Normal input

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit : mm [inch]

115 [4.53]6 [.24]7 [.28] 6 [.24] 7 [.28]

DIN rail

(35mm wide)

(3 [.12]) (4 [.16])

24 [.94] 72 [2.83]

55 [2.17]

R80FST4NJ

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7029 P. 7 / 7

■CONNECTION DIAGRAM

Ai1

Ai2

Ai3

Ai4

AG1

AG2

AG3

AG4

DC voltage/ current input 1

DC voltage/ current input 2

DC voltage/ current input 3

DC voltage/ current input 4

CONNECTOR

INTERNAL BUS

INTERNAL POWER

EXC. SUPPLY

Input Connector

WIRING INSTRUCTIONS

■Tension clamp terminal block

Unit side connector: MC1,5/16-GF-3,5 (Phoenix Contact)

Applicable connector: FMC1,5/16-STF-3,5

(Phoenix Contact)

Applicable wire size: 0.2 − 1.5 mm2

Stripped length: 10 mm

Recommended solderless terminal

• AI0,25−10YE 0.25 mm2(Phoenix Contact)

• AI0,34−10TQ 0.34 mm2(Phoenix Contact)

• AI0,5−10WH 0.5 mm2(Phoenix Contact)

• AI0,75−10GY 0.75 mm2(Phoenix Contact)

• A1−10 1.0 mm2(Phoenix Contact)

• A1,5−10 1.5 mm2(Phoenix Contact)

Table des matières

Autres manuels M-system Unité de contrôle

M-system

M-system R7M-EC16B Manuel utilisateur

M-system

M-system R7C-EC8C Manuel utilisateur

M-system

M-system R3-PA8 Manuel utilisateur

M-system

M-system R3-NM3 Manuel utilisateur

M-system

M-system R3-NM1 Manuel utilisateur

M-system

M-system R3-NL1 Manuel utilisateur

M-system

M-system R7ML-EC8B Manuel utilisateur

M-system

M-system R30YV4 Manuel utilisateur

M-system

M-system R5-NE1 Manuel utilisateur

M-system

M-system R3-ND1 Manuel utilisateur

M-system

M-system R7HL-DC16B-R Manuel utilisateur

M-system

M-system R3-PA4 Manuel utilisateur

M-system

M-system R3-AR4 Manuel utilisateur

M-system

M-system R80ND2 Manuel utilisateur

M-system

M-system R7M-EA8 Manuel utilisateur

M-system

M-system R7D-EA16 Manuel utilisateur

M-system

M-system M8YC Manuel utilisateur

M-system

M-system R7ML-DC16A Manuel utilisateur

M-system

M-system 61F Manuel utilisateur

M-system

M-system R6-NP1 Manuel utilisateur

M-system

M-system R7M-EC8A Manuel utilisateur

M-system

M-system R7M-DC4G Manuel utilisateur

M-system

M-system R3-NMW1F Manuel utilisateur

M-system

M-system R3-NC3 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur