Lightolier 1004ICVN Instructions d'utilisation

INSTRUCTION SHEET NO.

IS:1004ICV

B1204 Page 1 of 4

INSTALLATION PROCEDURE FOR LOW VOLTAGE

INSULATED CEILING FRAME-IN-KIT 1004ICV, 1004ICVN

1. FRAME-IN (Fig. A)

Locate fixture along joist and line up bottom edge of HINGED

MOUNTING BAR with the bottom of joist and fasten in place.

Fig. A

Frame-In

Fig. B

Wire-In

Fig. C

Swing-Up

Fig. D

Close-In

Fig. E

Snap-On

Fig. F

Push-Up

For suspended ceilings:

•Rotate HINGED BAR ENDS to position shown

and fully extend bars.

•Crimp bottom of edge of CHANNEL to prevent

rotation of HINGED BAR ENDS.

•Bend NON-HINGED end of mounting bar at

featured hole location and extend out.

•Position notched area of MOUNTING BARS onto

T-BAR and lock by bending TAB underneath

T-BAR BEAD as shown.

•For suspended ceiling, make certain that bottom

of Mounting Frame is no higher than 1” above

ceiling line.

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations.

To assure full compliance with local codes and regulations, check with your local electrical inspector before

installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

LIGHTOLIER a GENLYTE company.

631 Airport Road, Fall River, MA 02720

NEW CONSTRUCTION

NOTE: I.C. Frame-in Kit may be used in direct contact with insulation.

WARNING: USE ONLY WITH LIGHTOLIER REFLECTOR TRIMS MARKED WITH I.C. LAMPING INFORMATION. USE OF OTHER

MANUFACTURERS’ TRIMS VOIDS THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD

HINGED MOUNTING BAR

5 5/8”

6”

CENTER LINE OF

APERTURE OPENING

Fig. G

Note: Integral nail version available

TAB

T-BAR

HINGED BAR ENDS

CHANNEL

TAB

BEND AT TAB

BEND AT HOLE

FOR JOIST SPACING LESS THAN 16” ON CENTER (TO 12” ON CENTER):

•MOUNTING BAR CHANNELS can be shortened and used as

nailing legs in tight spaces. Simply remove INNER BAR from

holed CHANNEL, bend CHANNEL at appropriate point and

use extra screw to secure it to the joist. (Fig. G)

INSTRUCTION SHEET NO.

IS:1004ICV

B1204 Page 3 of 4

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations.

To assure full compliance with local codes and regulations, check with your local electrical inspector before

installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

LIGHTOLIER a GENLYTE company.

631 Airport Road, Fall River, MA 02720

8. LAMPING (Fig. H)

1. Make sure that power is OFF when lamping or relamping.

Remove LAMP RING from TRIM by pulling straight down.

2. Remove LAMP SHIELD from LAMP RING.

3. Place LAMP SHIELD on back of LAMP (MR-16) and insert both

between LAMP SPRINGS until face of lamp sits firmly on GLASS LAMP

GUARD (Fig. J).

WARNING: RISK OF FIRE. LAMP SHIELD MUST BE INSTALLED.

4. Attach SOCKET to bi-pin prongs on LAMP.

5. Insert LAMP RING with LAMP SHIELD, LAMP and GLASS LAMP

GUARD back into TRIM.

FEMALE CONNECTORS

(ATTACHED TO FIXTURE WIRES)

MALE CONNECTORS

(ATTACHED TO SOCKET WIRES)

MR16 SOCKET

LAMP SPRING

Fig. H

LAMP SHIELD

INSULATING SLEEVING

GLASS LAMP GUARD

SOCKET

LAMP RING

Fig. J

NOTE: 1. LOW VOLTAGE FIXTURES should be

dimmed only with special dimmers intended

specifically for that purpose. Use Lightolier

Lytemode, Scenist, Crescendo VA, Neptune VA,

Precision VA, Easyset VA, Sunrise VA, Radiant

VA or equivalent products by others or variable

autotransformers or electronic dimmers

intended for use with low voltage fixtures.

2. Low voltage fixtures may produce audible

sound which may be objectionable in acousti-

cally critical areas.

LAMP

WARNING: 1. LAMP MANUFACTURERS REQUIRE THE GLASS LAMPGUARD BE IN PLACE BEFORE ENERGIZING LAMP, AND THAT GREAT

CARE MUST BE TAKEN THAT LAMP IS FULLY COOLED BEFORE RELAMPING. AVOID FINGER MARKS ON INSIDE OF LAMP FOR THEY MAY

CAUSE SHORT LAMP LIFE AND POSSIBLE BREAKAGE. 2. USE ONLY REFLECTOR TRIMS

PROVIDED BY LIGHTOLIER INC. USE OF OTHER

MANUFACTURER'S REFLECTOR TRIMS VOIDS THE UNDERWRITERS LABORATORIES

LISTING AND COULD CONSTITUTE A FIRE HAZARD.

9. TRANSFORMER REPLACEMENT (Fig. K)

1. Make sure power is off.

2. Remove REFLECTOR TRIM from ceiling.

3. Remove SCREW and lift TRANSFORMER off bracket.

4. Remove J-BOX COVER by removing wing nut.

5. Unsplice primary leads in J-BOX.

6. Remove primary leads from J-BOX cover and clip attached to side

of housing.

7. Cut secondary (red) leads 6" to 8" from TRANSFORMER and dis-

card faulty transformer.

8. Install new TRANSFORMER:

(WARNING: RISK OF FIRE. Transformer contains fixture thermal

protector. Replace as shown and described below. Use only

replacement transformer obtained from LIGHTOLIER.)

a. Splice secondary (red) leads to socket leads.

b. Attach TRANSFORMER to BRACKET with SCREW, making

sure that the side of transformer that has the wire leads is

facing the housing wall (Fig.L)

c. Put primary leads through clip and bushing in the J-BOX

COVER.

e. Wire primary leads to supply leads.

f. Replace J-BOX COVER.

g. Install REFLECTOR TRIM.

Fig. K

ROTO CLIPS

JUNCTION BOX

MAX. OF (6) #12 AWG BRANCH

CIRCUIT CONDUCTORS SUITABLE

FOR AT LEAST 90° C PERMITTED

IN JUNCTION BOX.

TRANSFORMER

PRIMARY: 120V, 60HZ

SECONDARY: 110V, 50W LOAD

SCREW

SECONDARY

(RED) LEADS

PRIMARY

LEADS

CLIP

INSTRUCTION SHEET NO.

IS:1004ICV

B1204 Page 4 of 4

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations.

To assure full compliance with local codes and regulations, check with your local electrical inspector before

installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

LIGHTOLIER a GENLYTE company.

631 Airport Road, Fall River, MA 02720

APERTURE

HOLE

TRANSFORMER

WIRE LEADS

HOUSING

WALL

Fig. L

Ce manuel convient aux modèles suivants

Autres manuels Lightolier Luminaire

Lightolier

Lightolier STA 1'x4' 2 LAMP Manuel utilisateur

Lightolier

Lightolier Calculite 7790QD Manuel utilisateur

Lightolier

Lightolier QVS2GPFLV317 Manuel utilisateur

Lightolier

Lightolier LP100 Manuel utilisateur

Lightolier

Lightolier SL103A Manuel utilisateur

Lightolier

Lightolier Calculite Matrix 4X9 Manuel utilisateur

Lightolier

Lightolier IS-CTS3_FLNGLSS Mode d’emploi

Lightolier

Lightolier Lytecaster 1101FEL Manuel utilisateur

Lightolier

Lightolier Calculite ProSpec PA1H3870 Manuel utilisateur

Lightolier

Lightolier 4X4 MATRIX SERIES Manuel utilisateur

Lightolier

Lightolier ProSpec 26030W Manuel utilisateur

Lightolier

Lightolier Coffaire II CFH1GPF Manuel utilisateur

Lightolier

Lightolier QVS2GPFOS232 Manuel utilisateur

Lightolier

Lightolier BOWSHIELD “ADA” WALL BRACKET SERIES Mode d’emploi

Lightolier

Lightolier LL4MF8LX254 Manuel utilisateur

Lightolier

Lightolier QHE2GPFOP228 Manuel utilisateur

Lightolier

Lightolier CORD AND PLUG CONNECTOR Instructions d'utilisation

Lightolier

Lightolier Lytespan 8113 Manuel utilisateur

Lightolier

Lightolier Calculite ProSpec PA1P3075 Manuel utilisateur

Lightolier

Lightolier CCLRD01 Mode d’emploi

Lightolier

Lightolier ProSpec 26238 Manuel utilisateur

Lightolier

Lightolier REFLECTOR TRIM Manuel utilisateur

Lightolier

Lightolier SW STRIP Manuel utilisateur

Lightolier

Lightolier Lytecaster 1124 Manuel utilisateur

Manuels Luminaire populaires d'autres marques

Emos

Emos CLASSIC ZY1431T Manuel utilisateur

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuel utilisateur

Hedler

Hedler C 12 silent Manuel utilisateur

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuel utilisateur

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuel utilisateur

Lightmaxx

Lightmaxx Shaft 5R Manuel utilisateur

Triarch

Triarch 31083 Manuel utilisateur

Philips

Philips 32614 Series Manuel utilisateur

IKEA

IKEA TIVED Manuel utilisateur

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuel utilisateur

Martin

Martin MAC 250 Krypton Manuel utilisateur

Cooper Lighting

Cooper Lighting Halo L3232E Manuel utilisateur

Stageline

Stageline ODW-2410RGBW Manuel utilisateur

Light Sky

Light Sky Tornado Series Manuel utilisateur

ArtFox

ArtFox Beam 15R extreme Manuel utilisateur

GLG

GLG multispot 330 Manuel utilisateur

Home Accents Holiday

Home Accents Holiday TY052-1924-1 Manuel utilisateur

SELF Electronics

SELF Electronics FLEX Manuel utilisateur