Lenovo 7D7Y Manuel utilisateur

Service Guide for DM120S, DM240S, and

DM600S

Machine Types: 7Y58, 7Y59, 7Y43, 7D7Y, 7D7X, 7D7Z

Second Edition (September 2021)

L M TED AND RESTR CTED R GHTS NOT CE: f data or software is delivered pursuant to a General Services

Administration (GSA) contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-

05925.

Contents

Chapter 1. Hot-swapping a disk drive in a

DM240S or DM120S disk shelf. . . . . . 1

Chapter 2. Hot-swapping a disk

drive in a DM600S disk shelf . . . . . . . 5

Chapter 3. Hot-swapping a power

supply . . . . . . . . . . . . . . . . . 11

Chapter 4. Replacing a fan module in

a DM600S disk shelf . . . . . . . . . . 15

Chapter 5. Replacing a drive drawer

in a DM600S disk shelf . . . . . . . . . 17

Removing the cable chains . . . . . . . . . . 18

Removing a drive drawer . . . . . . . . . . . 23

nstalling a drive drawer. . . . . . . . . . . . 25

Attaching the cable chains . . . . . . . . . . 28

Chapter 6. Hot-swapping or

replacing an IOM12 module . . . . . . 33

Chapter 7. Hot-removing disk

shelves with IOM12 modules . . . . . 37

Chapter . Monitoring disk shelf

LEDs . . . . . . . . . . . . . . . . . . 43

Operator display panel LEDs. . . . . . . . . . 43

OM12 module LEDs . . . . . . . . . . . . . 44

Power supply LEDs . . . . . . . . . . . . . 44

Fan LEDs on DM600S disk shelves . . . . . . . 45

Disk drive LEDs . . . . . . . . . . . . . . . 46

Appendix A. Contacting Support . . . 49

Appendix B. Notices. . . . . . . . . . 51

Trademarks . . . . . . . . . . . . . . . . 52

Index . . . . . . . . . . . . . . . . . . 53

ii Service Guide for DM120S, DM240S, and DM600S

Chapter 1. Hot-swapping a disk drive in a DM240S or DM120S

disk shelf

You can hot-swap a failed disk drive in a DM240S or DM120S disk shelf—nondisruptively replace a disk

drive in a system that is powered on and serving data ( /O is in progress). When a disk drive fails, the system

logs a warning message to the system console indicating which disk drive has failed. n addition, the

attention (amber) LED on the operator display panel and the attention (amber) LED on the failed disk drive

illuminate.

Before you begin

• The disk drive that you are installing must be supported by the DM240S or DM120S disk shelf.

Lenovo Press

• All other components in the system must be functioning properly; if not, contact technical support.

• The disk drive you are removing must be failed.You can verify the disk drive is failed by running the

storage disk show -broken command. The failed disk drive appears in the list of failed disk drives. f it does

not, you should wait, and run the command again.

Note: t can take up to several hours for the disk drive to appear in the list of failed disk drives.

• f you are replacing a self-encrypting disk (SED), you must follow the instructions for replacing an SED in

the Disks and Aggregates Power Guide. The instructions describe additional steps you must perform

before and after replacing an SED.

ONTAP 9 Disks and Aggregates Power Guide

About this task

• You should take steps to avoid electrostatic discharge (ESD):

– Keep the disk drive in the ESD bag until you are ready to install it.

– Open the ESD bag by hand or cut the top off with a pair of scissors.

Attention: Do not insert a metal tool or knife into the ESD bag.

– Always wear an ESD wrist strap grounded to an unpainted surface on your storage enclosure chassis.

f a wrist strap is unavailable, touch an unpainted surface on your storage enclosure chassis before

handling the disk drive.

• You should take steps to handle disk drives carefully:

– Always use two hands when removing, installing, or carrying a disk drive to support its weight.

Attention: Do not place hands on the disk drive boards exposed on the underside of the disk drive

carrier.

– You should place disk drives on cushioned surfaces, and never stack disk drives on top of each other.

– You should be careful not to bump disk drives against other surfaces.

• Disk drives should be kept away from magnetic devices.

Attention: Magnetic fields can destroy all data on the disk drive and cause irreparable damage to the disk

drive circuitry.

• Best practice is to have the current version of the Disk Qualification Package (DQP) installed before hot-

swapping a disk drive. Having the current version of the DQP installed allows your system to recognize

and utilize newly qualified disk drives; therefore, avoiding system event messages about having non-

current disk drive information. You also avoid the possible prevention of disk partitioning because disk

drives are not recognized. The DQP also notifies you of non-current disk drive firmware.

Lenovo Data Center Support

• Best practice is to have the current versions of disk shelf ( OM) firmware and disk drive firmware on your

system before adding new disk shelves, shelf FRU components, or SAS cables. Current versions of

firmware can be found on the Lenovo Support Web site.

Lenovo Data Center Support

• Disk drive firmware is automatically updated (nondisruptively) on new disk drives with non current

firmware versions.

Note: Disk drive firmware checks occur every two minutes.

• f needed, you can turn on the disk shelf's location (blue) LEDs to aid in physically locating the affected

disk shelf:

storage shelf location-led modify -node node_name -shelf-name shelf_name -led-status on

A disk shelf has three location (blue) LEDs: one on the operator display panel and one on each OM12

module. Location LEDs remain illuminated for 30 minutes. You can turn them off by entering the same

command, but using the off option.

• f needed, you can refer to the Monitoring disk shelf LEDs section for information about the meaning and

location of disk shelf LEDs on the operator display panel and FRU components.

The video for this task is available at:

• Youtube: https://www.youtube.com/playlist?list=PLYV5R7hVcs-Bl5q5uq V0US3rLklB5GOP

• Youku: https://list.youku.com/albumlist/show/id_51948223

Step 1. f you want to manually assign disk ownership for the replacement disk drive, you need to disable

disk ownership automatic assignment if it is enabled; otherwise, go to the next step.

Note: You need to manually assign disk ownership if disk drives in the stack are owned by both

controllers in an HA pair.

Note: You manually assign disk ownership and then reenable disk ownership automatic

assignment later in this procedure.

a. Verify if disk ownership automatic assignment is enabled: storage disk option show

f you have an HA pair, you can enter the command at the console of either controller.

f disk ownership automatic assignment is enabled, the output shows “on” (for each controller)

in the “Auto Assign” column.

b. f disk ownership automatic assignment is enabled, you need to disable it:

storage disk option modify -node node_name -autoassign off

You need to disable disk ownership automatic assignment on both controllers in an HA pair.

Step 2. Properly ground yourself.

Step 3. Unpack the new disk drive, and set it on a level surface near the disk shelf.Save all packaging

materials for use when returning the failed disk drive.

Note: Lenovo requires that all returned disk drives be in a ESD-rated bag.

Step 4. Physically identify the failed disk drive from the system console warning message and the

illuminated attention (amber) LED on the disk drive.

2Service Guide for DM120S, DM240S, and DM600S

Note: The activity (green) LED on a failed disk drive can be illuminated (solid), which indicates the

disk drive has power, but should not be blinking, which indicates /O activity. A failed disk drive has

no /O activity.

Step 5. Press the release button on the disk drive face, and then pull the cam handle to its fully open

position to release the disk drive from the mid plane.

When you press the release button, the cam handle on the disk drive springs open partially.

Note: Disk drives in a DM120S disk shelf are arranged horizontally with the release button located

on the left of the disk drive face. Disk drives in a DM240S disk shelf are arranged vertically with the

release button located at the top of the disk drive face.

The following illustrations show disk drives in a DM120S disk shelf:

Step 6. Slide out the disk drive slightly to allow the disk to safely spin down, and then remove the disk drive

from the disk shelf.A disk can take up to one minute to safely spin down.

Note: When handling a disk drive, always use two hands to support its weight.

Step 7. Using two hands, with the cam handle in the open position, insert the replacement disk drive into

the disk shelf, firmly pushing until the disk drive stops.

Note: Wait a minimum of 10 seconds before inserting a new disk drive. This allows the system to

recognize that a disk drive was removed.

Note: Do not place hands on the disk drive boards that are exposed on the underside of the disk

carrier.

Chapter 1.Hot-swapping a disk drive in a DM240S or DM120S disk shelf 3

Step 8. Close the cam handle so that the disk drive is fully seated into the mid plane and the handle clicks

into place.Be sure to close the cam handle slowly so that it aligns correctly with the face of the disk

drive.

Step 9. f you are replacing another disk drive, repeat Steps 3 through 8.

Step 10. Verify the disk drive's activity (green) LED is illuminated.When the disk drive's activity LED is solid

green, it means the disk drive has power. When the disk drive's activity LED is blinking, it means

the disk drive has power and /O is in progress.

Step 11. f you disabled disk ownership automatic assignment in Step 1, manually assign disk ownership,

and then reenable disk ownership automatic assignment if needed:

a. Display all unowned disks: storage disk show -container-type unassigned

b. Assign each disk: storage disk assign -disk disk_name -owner owner_name

You can use the wildcard character to assign more than one disk at once.

c. Reenable disk ownership automatic assignment if needed:

storage disk option modify -node node_name -autoassign on

You need to reenable disk ownership automatic assignment on both controllers in an HA pair.

Step 12. f you are instructed to return the failed part, follow all packaging instructions and use any

packaging materials that are provided.

4Service Guide for DM120S, DM240S, and DM600S

Chapter 2. Hot-swapping a disk drive in a DM600S disk shelf

You can hot-swap a failed disk drive in a DM600S disk shelf—nondisruptively replace a disk drive in a

system that is powered on and serving data ( /O is in progress). When a disk drive fails, the system logs a

warning message to the system console indicating which disk drive has failed. n addition, the attention

(amber) LED on the operator display panel, the attention LED on the drawer containing the failed disk, and

the attention LED on the failed disk drive (visible when the drawer is open) illuminate.

Before you begin

• The replacement disk drive must be supported by the DM600S disk shelf.

Lenovo Press

• All other components in the system must be functioning properly; if not, contact technical support.

• The disk drive you are removing must be failed.You can verify the disk drive is failed by running the

storage disk show -broken command. The failed disk drive appears in the list of failed disk drives. f it does

not, you should wait, and run the command again.

Note: t can take up to several hours for the disk drive to appear in the list of failed disk drives.

• f you are replacing a self-encrypting disk (SED), you must follow the instructions for replacing an SED in

the Disks and Aggregates Power Guide. The instructions describe additional steps you must perform

before and after replacing an SED.

ONTAP 9 Disks and Aggregates Power Guide

About this task

• You should take steps to avoid electrostatic discharge (ESD):

– Keep the disk drive in the ESD bag until you are ready to install it.

– Open the ESD bag by hand or cut the top off with a pair of scissors.

Attention: Do not insert a metal tool or knife into the ESD bag.

– Always wear an ESD wrist strap grounded to an unpainted surface on your storage enclosure chassis.

f a wrist strap is unavailable, touch an unpainted surface on your storage enclosure chassis before

handling the disk drive.

• You should take steps to handle disk drives carefully:

– Always use two hands when removing, installing, or carrying a disk drive to support its weight.

Attention: Do not place hands on the disk drive boards exposed on the underside of the disk drive

carrier.

– You should place disk drives on cushioned surfaces, and never stack disk drives on top of each other.

– You should be careful not to bump disk drives against other surfaces.

• Disk drives should be kept away from magnetic devices.

Attention: Magnetic fields can destroy all data on the disk drive and cause irreparable damage to the disk

drive circuitry.

• Best practice is to have the current version of the Disk Qualification Package (DQP) installed before hot-

swapping a disk drive. Having the current version of the DQP installed allows your system to recognize

and utilize newly qualified disk drives; therefore, avoiding system event messages about having non-

current disk drive information. You also avoid the possible prevention of disk partitioning because disk

drives are not recognized. The DQP also notifies you of non-current disk drive firmware.

Lenovo Data Center Support

• Best practice is to have the current versions of disk shelf ( OM) firmware and disk drive firmware on your

system before adding new disk shelves, shelf FRU components, or SAS cables. Current versions of

firmware can be found on the Lenovo Support Web site.

Lenovo Data Center Support

• Disk drive firmware is automatically updated (nondisruptively) on new disk drives with non current

firmware versions.

Note: Disk drive firmware checks occur every two minutes.

• f needed, you can turn on the disk shelf's location (blue) LEDs to aid in physically locating the affected

disk shelf:

storage shelf location-led modify -node node_name -shelf-name shelf_name -led-status on

A disk shelf has three location (blue) LEDs: one on the operator display panel and one on each OM12

module. Location LEDs remain illuminated for 30 minutes. You can turn them off by entering the same

command, but using the off option.

• f needed, you can refer to the Monitoring disk shelf LEDs section for information about the meaning and

location of disk shelf LEDs on the operator display panel and FRU components.

• The DM600S drive shelf consist of five drive drawers (drive drawer 1 at the top through drive drawer 5 at

the bottom) that each contain 12 drive slots.

• The following illustration shows how the drives are numbered from 0 to 11 in each drive drawer within the

shelf.

6Service Guide for DM120S, DM240S, and DM600S

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Lenovo Stockage

Lenovo

Lenovo ThinkCentre M70s Gen 2 Manuel utilisateur

Lenovo

Lenovo Storage DX8200D series Guide de l'utilisateur

Lenovo

Lenovo Secure Desktop Drive Manuel utilisateur

Lenovo

Lenovo ThinkSystem Heavy Duty Manuel utilisateur

Lenovo

Lenovo ThinkSystem DE Series Manuel utilisateur

Lenovo

Lenovo D1224 Manuel utilisateur

Lenovo

Lenovo ThinkSystem DM240N Manuel utilisateur

Lenovo

Lenovo ThinkStation P3 Tower Manuel utilisateur

Lenovo

Lenovo DE2000H Manuel

Lenovo

Lenovo ThinkPad Hard Disk Drive Manuel utilisateur

Lenovo

Lenovo S3500 Manuel utilisateur

Lenovo

Lenovo ThinkSystem DS Series Manuel d'utilisation

Lenovo

Lenovo ThinkServer TD350 Manuel utilisateur

Lenovo

Lenovo IBM Storwize V7000 Manuel utilisateur

Lenovo

Lenovo D1012 Manuel d'utilisation

Lenovo

Lenovo EMC2 px4-400r Manuel utilisateur

Lenovo

Lenovo ThinkServe LTO Manuel utilisateur

Lenovo

Lenovo S2200 Manuel utilisateur

Lenovo

Lenovo Lenovo Ultra Secure Memory Key Manuel utilisateur

Lenovo

Lenovo ThinkSystem Micro DataCenter 6U Acoustic Manuel utilisateur

Lenovo

Lenovo 41N3015 - 250GB Serial Ata Hard Disk Drive Manuel utilisateur

Lenovo

Lenovo IBM Half-high LTO Generation 4 Manuel utilisateur

Lenovo

Lenovo DM120S Manuel utilisateur

Lenovo

Lenovo S3200 Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur