Lenovo ThinkSystem DM3000 series Manuel
Install hardwarePrepare for installation Cable storage Complete system setup
and configuration
1 2 3 4
Prepare for installation |Stage 1
You provide
In the box
Pre-setup
1. Unpack all boxes and inventory contents.
2. Complete the Cluster Configuration Worksheet.
Cluster Interconnect cables 10 GbE network cables
(order dependent)
Optical network cables
(order dependent)
Data and cluster
Interconnect cables Storage cables
mini-SAS HD to mini-SAS HD cables
Additional cables
Power
cables
Ethernet
cables
micro USB
console cable
Screwdriver Additional network cables ClientRack space
2U per chassis For connecting your storage system
to your network switch and
Microsoft® Windows® client
With a USB/serial connection
and access to a Web browser to
configure your storage system
DM3000x and DM5000x
Systems
Installation and Setup Instructions
Printed in China
(1P) P/N: SP47A24952
Install hardware |Stage 2
A
B
1
2
Unified configuration
1
2
AC AC
• Install the rail kits, as needed, and then install and
secure your system using the instructions included with the kit.
• Attach cable management devices (as shown).
• Place the bezel on the front of the system.
Install system in a rack
2
Rear view of the controllers
1
3Cable controller for cluster
4
2
2
3
1
Ethernet cables
Ethernet cables
Cluster interconnect cables
Power cables
4Connect both power cords
1
2
Retaining clipsRetaining clips
2
To data network
switches
3
To management
network switches
1
A
B
1
2
Ethernet configuration
10 GbE
network
cables
Optical
network
cables
OR
Cluster
Ethernet cables for use
with Ethernet configuration
Unified
configuration
For Unified configuration
For Ethernet configuration
DO NOT turn on the power supply switches.
Strap the cables to the cable
management arms. (not shown)
Connect port e0a to
port e0a and port e0b to port e0b.
Connect ports e0c and e0d OR ports e0e
and e0f to the data network switches.
Connect ports e0c and e0e OR ports e0d
and e0f to the data network switches.
Connect the wrench port (e0M)
on both controller modules to the
management subnet switches.
Connect the power cables to both power supplies.
• Use the retaining clips.
• Connect power cables to different power sources.
Cable storage |Stage 3
STOP HERE. If you have NO external storage, skip to stage 4, complete system setup and configuration.
Cabling a DM3000x or DM5000x series
with NO external storage
Cabling a DM3000x or DM5000x series
WITH external storage (DM120S or DM240S)
A
B
Connect the SAS ports of both controllers:
• Controller 1 0a to Controller 2 0b
• Controller 1 0b to Controller 2 0a
2
1
3
Connect the shelf-to-shelf ports
Connect each node to IOM A in the stack
Connect each node to IOM B in the stack
1
2
AC AC
IOM12
21
LNK L NK
43
LNK L NK
IOM12
21
LNK L NK
43
LNK L NK
IOM12
21
LNK L NK
43
LNK L NK
IOM12
21
LNK L NK
43
LNK L NK
IOM12
21
LNK L NK
43
LNK L NK
IOM12
21
LNK L NK
43
LNK L NK
2
AC
1
AC
1
2
AC AC
1
2
AC AC
First
shelf
IOMA
Last
shelf
IOMB
1
2
AC AC
Dual controller system
Storage cables
Storage cables Orient the cable connector
pull-tab in the correct direction,
then gently push the connector
into place until it clicks.
Note: To unplug a cable, gently pull
the tab to release the locking
mechanism.
Pull-tab
facing down
A
B
1
2
1Cable and configure your client
Complete system setup and configuration |Stage 4
If your system has one or more drive shelves, set the shelf IDs:
1. Power on the drive shelf, and then remove the end cap on the left of the shelf.
2. Press and hold the orange button until the first digit blinks, and then press the
button to advance the first digit (0-9) to the desired number. The first digit
continues to blink.
3. Press and hold the button until the second digit blinks, and then press the button
to advance the second digit (0-9) to the desired number. The first digit stops blinking,
and the second digit continues to blink. Each expansion shelf requires a unique shelf ID.
4. Press and hold the button until the second digit stops blinking, and then replace
the end cap on the shelf.
5. Wait about 10 seconds for both digits to start blinking again and for the LED to
illuminate, and then power-cycle the drive shelf to make the shelf ID take effect.
6. Repeat these steps for any remaining drive shelves.
2
3
4
Turn on the power
switches to both nodes
Configure your system using the Application Setup Wizard
A
B
1
2
Connect the client to the switch
on the management subnet:
a. Give the client a TCP/IP address
on the management subnet.
b. Set the console port on the client
to 115,200 baud with N-8-1 and flow
control off.
Connect the console cable to the client and
the console port on the controller module.
micro USB console cable
Ethernet cable
2
1
1
2
AC AC
1
2
AC AC
DM3000x or DM5000x system
Client
Management subnet 2
1
Log into System Manager, as described on the back of your system, and then complete the storage provisioning wizards
found under Applications in System Manager.
1. Assign an initial node management IP address to one of the
nodes If you have DHCP configured on your management
network, record the IP address assigned to the new controllers.
Otherwise,
a. Open a console session using PuTTY, a terminal server,
or the equivalent for your environment.
b. Enter the node management IP address when prompted.
2. Use System Manager Guided Setup to configure
your cluster.
a. Point your browser to the address you
assigned in step 1:
https://x.x.x.x.
b. Enter the data from your Cluster Configuration
Worksheet.
All other systems:
SAN or NAS optimized system:
HELPFUL LINKS
• Lenovo Data Center Support Web site (worldwide):
http://datacentersupport.lenovo.com
•Lenovo Data Center Support Web site (China):
http://support.lenovo.com.cn/EsWeb/
First Edition (September 2018)
© Copyright Lenovo 2018.
LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to
a General Services Administration (GSA) contract, use, reproduction, or disclosure is
subject to restrictions set forth in Contract No. GS-35F-05925.
LENOVO is a trademark of Lenovo.
Microsoft and Windows are trademarks of the Microsoft group of companies.
All other trademarks are the property of their respective owners.
© 2018 Lenovo.
2U12
2U24
Shelf ID
change
button
Shelf ID
change
button
Autres manuels pour ThinkSystem DM3000 series
2
Ce manuel convient aux modèles suivants
1
Autres manuels Lenovo Stockage
Lenovo
Lenovo V3700 V2 XP Manuel utilisateur
Lenovo
Lenovo IBM Storwize V7000 Manuel utilisateur
Lenovo
Lenovo DE4000H Manuel
Lenovo
Lenovo ThinkSystem DM3000 series Manuel d'utilisation
Lenovo
Lenovo 43R2018 - ThinkPad 160 GB External Hard... Manuel utilisateur
Lenovo
Lenovo Iomega ix2 Manuel utilisateur
Lenovo
Lenovo ThinkSystem DM7100F Manuel
Lenovo
Lenovo 43N3424 Manuel utilisateur
Lenovo
Lenovo ThinkPad Hard Disk Drive Manuel utilisateur
Lenovo
Lenovo Optical M10 Feuille d'instructions
Lenovo
Lenovo ThinkServe LTO Manuel utilisateur
Lenovo
Lenovo EZ Media & Backup Center Manuel utilisateur
Lenovo
Lenovo ThinkSystem DM5100F Manuel d'utilisation
Lenovo
Lenovo Beacon Manuel du propriétaire
Lenovo
Lenovo Lenovo Ultra Secure Memory Key Manuel utilisateur
Lenovo
Lenovo Storage DX8200D series Guide de l'utilisateur
Lenovo
Lenovo 3000 N100 Manuel utilisateur
Lenovo
Lenovo ThinkPad Hard Disk Drive Manuel utilisateur
Lenovo
Lenovo IBM Storwize V5000 Manuel utilisateur
Lenovo
Lenovo Storage N3310 Manuel utilisateur
Manuels Stockage populaires d'autres marques
Spectra Logic
Spectra Logic T-Series Spectra T50e Manuel utilisateur
Panasonic
Panasonic LKM-F931-1 Manuel utilisateur
Tabernus
Tabernus Enterprise Erase E2400 Manuel utilisateur
Rocstor
Rocstor COMMANDER 3F series Manuel utilisateur
HP
HP P9000 Manuel utilisateur
Western Digital
Western Digital Ultrastar Data60 Manuel utilisateur