Ledj STAR18 Manuel utilisateur
LEDJ Tri LED Matrix Table Cloth - STAR18
USER MANUAL
www.prolight.co.uk
LEDJ Tri LED Matrix Table Cloth Safety
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOUR INITIAL START-UP!
CAUTION!
Keep this equipment away from rain,
moisture and liquids.
SAFETY INSTRUCTIONS
Every person involved with the installation, operation & maintenance of this
equipment should:
- Be competent
- Follow the instructions of this manual
CAUTION! TAKE CARE USING THIS EQUIPMENT!
HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!
Before your initial start-up, please make sure that there is no damage caused during
transportation. Should there be any, consult your dealer and do not use the
equipment.
To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
Please note that damages caused by user modifications to this equipment are not
subject to warranty.
LEDJ Tri LED Matrix Table Cloth Safety
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused
by the non-observance of this manual or any unauthorised modification to the
equipment.
• Never let the power-cable come into contact with other cables. Handle the power-cable
and all mains voltage connections with particular caution!
• Never remove warning or informative labels from the equipment.
• Do not open the equipment and do not modify the equipment.
• Do not connect this equipment to a dimmer-pack.
• Do not switch the equipment on and off in short intervals, as this will reduce the
system’s life.
• Only use the equipment indoors.
• Do not expose to flammable sources, liquids or gases.
• Always disconnect the power from the mains when equipment is not in use or before
cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the
power-cable.
• Make sure that the available voltage is between 220v/240v.
• Make sure that the power-cable is never crimped or damaged. Check the equipment and
the power-cable periodically.
• If the equipment is dropped or damaged, disconnect the mains power supply immediately.
Have a qualified engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic temperature fluctuation (e.g. after
transportation), do not switch it on immediately. The arising condensation might damage
the equipment. Leave the equipment switched off until it has reached room temperature.
• If your product fails to function correctly, discontinue use immediately. Pack the unit
securely (preferably in the original packing material), and return it to your Prolight dealer
for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be carried out by a qualified
technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.
• WARRANTY; One year from date of purchase.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual,
the product may suffer damage and the warranty becomes void.
Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,
lamp failure etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and property.
You should find inside the carton the following items:
1, Tri LED Matrix Table Cloth 2, Instruction manual 3, Controller 4, SD card
Technical Specifications:
DMX channels: 2
DMX, sound active and auto run modes
72 Ultra Bright Tri-colour LEDs
Hanging tabs on 3 sides
Fire retardent material
Power consumption: 25W
Power supply: 240V
Dimensions: 2.2 x 1M
Weight: 4Kgs
Overview:
LEDJ Tri LED Matrix Table Cloth Technical Specifications
Order code: STAR18
DMX IN DMX OUT SIGNAL DC OUT
DIPSWITCHES
MIC SENS
www.prolight.co.uk
POWER
SUPPLY
ON
OFF
Operations:
There are three operating modes to choose from;
1, Auto run 2, Sound Active 3, DMX
NOTE: Before use, please insert the supplied SD card and follow the instructions below.
Auto run mode
To set the Matrix table cloth in auto run mode, set all dip switches to the off position and use the
“SENSITIVITY/SPEED” control to set the desired running speed. The Matrix table cloth will now
run through all of its in-built programmes.
Sound active mode
To set the Matrix table cloth into sound active mode, set dip switch “10” to the ON position and
all others to the OFF position. Now use the “SENSITIVITY/SPEED” control to set the desired
sensitivity level.
DMX mode
DMX Control Mode
Operating in a DMX control mode environment gives the user the greatest flexibility when it comes
to customising or creating a show. In this mode you will be able to control each individual trait of the
cloth and each cloth independently. The Tri LED Matrix Table Cloth uses 2 channels of
control.
Use dip switches 1 – 9 to address each cloth accordingly.
Setting the DMX address
The DMX mode enables the use of a universal DMX controller. Each cloth requires a “start address”
from 1- 511. A cloth requiring one or more channels for control begins to read the data on the
channel indicated by the start address. For example, a cloth that occupies or uses 7 channels
of DMX and was addressed to start on DMX channel 100, would read data from channels:
100,101,102,103,104,105 and 106. Choose a start address so that the channels used do not
overlap. E.g. the next unit in the chain starts at 107.
DMX chart:
LEDJ Tri LED Matrix Table Cloth Operations
Channel
1
2
Value
0-9
10-255
10-239
Function
Blackout
Sound Active
Pattern selector
0-9 Blackout
0-255 Speed (slow to fast)
Notes
CH1 0-9 Blackout
240-255 Auto run
Further DMX cables can be purchased from all
good sound and lighting suppliers or Prolight
dealers.
Please quote:
CABL10 – 2M
CABL11 – 5M
CABL12 – 10M
DMX Control Mode
Operating in a DMX control mode environment gives the user the greatest flexibility when it comes
to customising or creating a show. In this mode you will be able to control each individual trait of
the fixture and each fixture independently.
Setting the DMX address
The DMX mode enables the use of a universal DMX controller. Each fixture requires a
“start address” from 1- 511. A fixture requiring one or more channels for control begins to read the
data on the channel indicated by the start address. For example, a fixture that occupies or uses 7
channels of DMX and was addressed to start on DMX channel 100, would read data from
channels: 100,101,102,103,104,105 and 106. Choose a start address so that the channels used
do not overlap. E.g. the next unit in the chain starts at 107.
DMX-512:
• DMX (Digital Multiplex) is a universal protocol used as a form of communication between
intelligent fixtures and controllers. A DMX controller sends DMX data instructions form the
controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the
DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have
a data “out” terminal).
DMX Linking:
• DMX is a language allowing all makes and models of different manufactures to be linked together
and operate from a single controller, as long as all fixtures and the controller are DMX compliant.
To ensure proper DMX data transmission, when using several DMX fixtures try to use the
shortest cable path possible. The order in which fixtures are connected in a DMX line does not
influence the DMX addressing. For example; a fixture assigned to a DMX address of 1 may be
placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a
fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to
address 1 to that unit, no matter where it is located in the DMX chain.
DATA Cable (DMX cable) requirements (for DMX operation):
• The LEDJ Tri LED Matrix Table Cloth can be controlled via DMX-512 protocol. The DMX
address is set on the back of the unit. Your unit and your DMX controller require a standard
3-pin XLR connector for data input/output (figure 1).
Figure 1
Also remember that DMX cable must be daisy chained and cannot be split.
LEDJ Tri LED Matrix Table Cloth DMX Set Up
Notice:
• Be sure to follow figures 2 & 3 when making your own cables. Do not connect the cable’s shield
conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer
casing. Grounding the shield could cause a short circuit and erratic behaviour.
Special Note: Line termination:
• When longer runs of cable are used, you may need to use a terminator on the last unit to
avoid erratic behaviour.
Using a cable terminator (part number CABL90) will decrease the possibilities of erratic
behaviour.
5-Pin XLR DMX Connectors:
• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin
XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin
XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the
correct cable conversion.
Termination reduces signal transmission problems
and interferance. it is always advisable to connect a
DMX terminal, (resistance 120 Ohm 1/4 W) between
pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.
LEDJ Tri LED Matrix Table Cloth DMX Set Up
LEDJ Tri LED Matrix Table Cloth Dip Switch Reference Chart
DMX Dip Switch Quick Reference Chart
Dip Switch Position
Table des matières
Autres manuels Ledj Projecteur
Ledj
Ledj Xterior Wash 131 Manuel utilisateur
Ledj
Ledj Slimline 9Q8 Manuel utilisateur
Ledj
Ledj LEDJ98 Manuel utilisateur
Ledj
Ledj Q Pix Batten LEDJ97 Manuel utilisateur
Ledj
Ledj PERFORMER 36 RGB Manuel utilisateur
Ledj
Ledj Eco LED 64 Manuel utilisateur
Ledj
Ledj INTENSE 12D4 CW Manuel utilisateur
Ledj
Ledj Slimline 36 RGBW Manuel utilisateur
Ledj
Ledj PERFORMER 54 RGBW Manuel utilisateur
Ledj
Ledj Q Colour Manuel utilisateur
Ledj
Ledj LEDJ280 Manuel utilisateur
Ledj
Ledj Q Colour LEDJ210 Manuel utilisateur
Ledj
Ledj LEDJ286 Manuel utilisateur
Ledj
Ledj Spectra Par 6HEX10 Manuel utilisateur
Ledj
Ledj HEX Par 7 Manuel utilisateur
Ledj
Ledj Intense 9HEX10 Manuel utilisateur
Ledj
Ledj Slimline 5Q5 Manuel utilisateur
Ledj
Ledj Q Batten LEDJ300 Manuel utilisateur
Ledj
Ledj Stage Par Quad MKII Manuel utilisateur
Ledj
Ledj LEDJ252B Manuel utilisateur
Manuels Projecteur populaires d'autres marques
VIZULO
VIZULO Micro Martin Guide de l'utilisateur
EuroLite
EuroLite LED IP FL-100 SMD Manuel utilisateur
Cooper Wheelock
Cooper Wheelock XB12 Manuel utilisateur
Allen + Roth
Allen + Roth 17624-000 Manuel utilisateur
ADJ
ADJ 4 STAGE PAK Manuel utilisateur
Cooper Lighting
Cooper Lighting EGL91SW233 Manuel utilisateur
