Ledj Eco LED 64 Manuel utilisateur

www.prolight.co.uk

Eco LED 64

(order code: LEDJ32)

USER MANUAL

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modifications to this equipment are not

subject to warranty.

LEDJ Eco LED 64 SAFETY

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modification to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Only use the equipment indoors.

• Do not expose to flammable sources, liquids or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualified engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature fluctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualified

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

LEDJ Eco LED 64 INTRODUCTION

Introduction

CONTROL FEATURES

• 6 channel DMX-512 Eco LED 64 Can

• Static/Dimmer/Strobe

• Individual control of Red, Green and Blue LEDs

Features

• 177 LEDs: - Red (60), Green (60), and Blue (57)

• Ultra Bright 10mm LEDs

• RGB colour mixing

• Built-in colour change programmes

• Power consumption: 32W

• Master/Slave mode

• Programmable from Any universal DMX-512 controller

Options

DMX Channel Summary

LEDJ Eco LED 64 OVERVIEW

Product Overview

Identificaion:

1) DMX in

2) DMX out

3) Fuse

4) Sensitivity control

5) Dip switches

Setup

Operating Instructions

The Eco LED-64 is a DMX-512 controllable, full RGB colour mixing Par Can made up of high

efficiency and super bright LED’s. There are three colour groups (red, blue and green) whose

intensity can be controlled individually allowing the creation of an unlimited range of colours.

The Eco LED-64 will operate in stand-alone, master/slave, sound activated and DMX-512

control.

LEDJ Eco LED 64 MASTER/SLAVE

Operation modes

Strobe Mode

To set the unit in strobe mode, set dip switch 1 to ON and all others to the OFF position. Now use

the sensitivity control to adjust the speed.

Fade mode

To set the unit in fade mode, set dip switch 2 to ON and all others to the OFF position. Now use

the sensitivity control to adjust the speed.

7 Colour Chase mode

To set the unit in 7 colour chase mode, set dip switch 3 to ON and all others to the OFF

position. Now use the sensitivity control to adjust the speed.

5 Colour Chase mode

To set the unit in 5 colour chase mode, set dip switch 4 to ON and all others to the OFF

position. Now use the sensitivity control to adjust the speed.

Red and Green Colour Chase Mode

To set the unit in red and green colour chase mode, set dip switch 5 to ON and all others to the

OFF position. Now use the sensitivity control to adjust the speed.

Static Colour Selection

To select a static colour, use any of the dip switches listed below;

Dip switch 6set to ON, obtains static Red

Dip switch 7set to ON, obtains static Green

Dip switch 8set to ON, obtains static Blue

Now use the sensitivity control to adjust the brightness.

Note: You can have any combination of switches 6, 7 and 8 to obtain any static colour mix.

Sound Activation

The Eco LED 64 Can has a built-in microphone which enables it to operate in Sound to Light

mode. Set the sensitivity control to the desired level, and the Eco LED 64 Can will change colour

to the beat of the music. Set dip switch 9 to ON and all others to the OFF position to activate

Sound Mode.

Master/Slave mode

Use any of the above modes to set the master unit. To set the unit(s) in slave mode set dip switch

10 to the ON position and all others to OFF.

Note: When all of the dip switches are set to OFF, the unit will automatically run in a RGB

colour chase. Use the sensitivity control to adjust the speed.

LEDJ Eco LED 64 CONTROL OPTIONS

Daisy Chain Connection

1) Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin

connector of the first fixture

2) Connect the end of the cable coming from the first fixture which will have a (female) 3 pin

connector to the input connector of the next fixture consisting of a (male) 3 pin connector.

Proceed to connect from the output as stated above to the input of the following fixture

and so on.

DMX Control Mode

Operating in a DMX control mode environment gives the user the greatest flexibility when it comes

to customising or creating a show. In this mode you will be able to control each individual trait of

the fixture and each fixture independently. The Eco LED 64 uses 6 channels of control.

Enable the DMX control by setting dip switch No: 10 to the ON position. Use dip switches 1 – 9 to

address each fixture accordingly.

Setting the DMX address

The DMX mode enables the use of a universal DMX controller. Each fixture requires a “start

address” from 1- 511. A fixture requiring one or more channels for control begins to read the data

on the channel indicated by the start address. For example, a fixture that occupies or uses 7

channels of DMX and was addressed to start on DMX channel 100, would read data from

channels: 100,101,102,103,104,105 and 106. Choose a start address so that the channels used

do not overlap. E.g. the next unit in the chain starts at 107.

POWER

LINE

INPUT FROM DMX CONTROLLER

(OPTIONAL) Use 3 pin XLR DMX cable

Continue

FUSE

POWER

FUSE

POWER

FUSE

POWER

FUSE

ON ON ON ON

IN OUT IN OUT IN OUT IN OUT

LEDJ Eco LED 64 CONTROL OPTIONS

Set the start address using the group of dip switches located usually on the back of the fixture.

Each dip switch has an associated value. Adding the value of each switch in the ON position will

provide the start address. Determining which switches to toggle ON given a specific start address

can be accomplished in the following manner. By subtracting the largest switch value possible

from the selected start address until zero is achieved.

EXAMPLE STARTING ADDRESS

Address 10

Pin NO: 4 = 8

Pin NO: 2 = 2

Total = 10

Address 24

Pin NO: 5 = 16

Pin NO: 4 = 8

Total = 24

DMX address using

simple maths

233 - (128 = 105,Turn on dip No: 8

105 - (64) = 41,Turn on dip No:7

41 - (32) = 9,Turn on dip No: 6

9 - (8) = 1,Turn on dip No: 4

1 - (1) = 0,Turn on dip No:1

You will most likely use the first available

number which maybe Number 1.This

number was selected for

example purposes

DIP SWITCH (DMX VALUE)

128

256

LEDJ Eco LED 64 DMX SET UP

DMX-512:

• DMX (Digital Multiplex) is a universal protocol used as a form of communication between

intelligent fixtures and controllers. A DMX controller sends DMX data instructions form the

controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have

a data “out” terminal).

DMX Linking:

• DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all fixtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX fixtures try to use the

shortest cable path possible. The order in which fixtures are connected in a DMX line does not

influence the DMX addressing. For example; a fixture assigned to a DMX address of 1 may be

placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a

fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to

address 1 to that unit, no matter where it is located in the DMX chain.

DATA Cable (DMX cable) requirements (for DMX operation):

• The Eco LED 64 can be controlled via DMX-512 protocol. The DMX address is set on the back

of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for data

input/output (figure 1).

Figure 1

Also remember that DMX cable must be daisy chained and cannot be split.

Further DMX cables can be purchased

from all good sound and lighting suppliers

or Prolight dealers.

Please quote:

CABL10 – 2M

CABL11 – 5M

CABL12 – 10M

Notice:

• Be sure to follow figures 2 & 3 when making your own cables. Do not connect the cable’s shield

conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer

casing. Grounding the shield could cause a short circuit and erratic behaviour.

Special Note: Line termination:

• When longer runs of cable are used, you may need to use a terminator on the last unit to

avoid erratic behaviour.

Using a cable terminator (part number CABL90) will decrease the possibilities of erratic

behaviour.

5-Pin XLR DMX Connectors:

• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin

XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin

XLR connectors in to a 3-pin line a cable adaptor must be used. The chart below details the

correct cable conversion.

Termination reduces signal transmission problems

and interferance. it is always advisable to connect a

DMX terminal, (resistance 120 Ohm 1/4 W) between

pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.

LEDJ Eco LED 64 DMX SET UP

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Ledj Projecteur

Ledj

Ledj Stage Wash 36 Manuel utilisateur

Ledj

Ledj STAGE COLOUR 24 TRI Manuel utilisateur

Ledj

Ledj Omni WA-36 Manuel utilisateur

Ledj

Ledj Q Batten LEDJ300 Manuel utilisateur

Ledj

Ledj LEDJ98 Manuel utilisateur

Ledj

Ledj ALU ZOOM PAR 64 Manuel utilisateur

Ledj

Ledj Quad illuminator Manuel utilisateur

Ledj

Ledj Intense 9HEX10 Manuel utilisateur

Ledj

Ledj Slimline 229 Manuel utilisateur

Ledj

Ledj Performer 18 Quad Zoom Manuel utilisateur

Ledj

Ledj LEDJ280 Manuel utilisateur

Ledj

Ledj LEDJ252B Manuel utilisateur

Ledj

Ledj Q Colour LEDJ210 Manuel utilisateur

Ledj

Ledj ALU ZOOM PAR 64 Manuel utilisateur

Ledj

Ledj Q Pix Batten LEDJ97 Manuel utilisateur

Ledj

Ledj Spectra Led Flood (Exterior) Manuel utilisateur

Ledj

Ledj INTENSE 12D4 CW Manuel utilisateur

Ledj

Ledj Stage Par Quad MKII Manuel utilisateur

Ledj

Ledj STAGE WASH U.V. 36 LEDJ106 Manuel utilisateur

Ledj

Ledj Slimline 7T3 Manuel utilisateur

Ledj

Ledj Slimline 36 RGBW Manuel utilisateur

Ledj

Ledj STAR18 Manuel utilisateur

Ledj

Ledj UV 100W COB Flood LEDJ185 Manuel utilisateur

Ledj

Ledj PERFORMER 54 RGBW Manuel utilisateur

Manuels Projecteur populaires d'autres marques

VIZULO

VIZULO Micro Martin Guide de l'utilisateur

EuroLite

EuroLite LED IP FL-100 SMD Manuel utilisateur

Cooper Wheelock

Cooper Wheelock XB12 Manuel utilisateur

Allen + Roth

Allen + Roth 17624-000 Manuel utilisateur

ADJ

ADJ 4 STAGE PAK Manuel utilisateur

Cooper Lighting

Cooper Lighting EGL91SW233 Manuel utilisateur

Max

Max 37496 Manuel utilisateur

BEGA

BEGA 85 143 Manuel utilisateur

Beamz

Beamz 151.226 Manuel utilisateur

EuroLite

EuroLite LED IP FL-8 Manuel utilisateur

Perel

Perel ELS3 Manuel utilisateur

Perel

Perel ELS3WD Manuel utilisateur

LumX

LumX LM 36130 Manuel utilisateur

Xtricity

Xtricity 4-80053 Manuel utilisateur

Stahl

Stahl 6521/4 Series Manuel utilisateur

Ecosense

Ecosense EcoSpec Manuel utilisateur

Ayrton

Ayrton minipanel FX Manuel utilisateur

Commercial Electric

Commercial Electric TPAR2-PC-4K-BZ Manuel utilisateur