Ledj Stage Wash 36 Manuel utilisateur

www.prolight.co.uk

Stage Wash 36

Order code: LEDJ102

USER MANUAL

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modications to this equipment are not

subject to warranty.

Stage Wash 36 Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modication to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualied engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature uctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualied

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

Stage Wash 36 Technical specications

Introduction

CONTROL FEATURES

• DMX channels: 3 & 6 selectable

• Blackout/Dimmer/Strobe

• Individual control of Red, Green and Blue LEDs

Product Overview

Setup

Operating Instructions

The Stage Wash 36 is a DMX-512 controllable, full RGB colour mixing wash made up of high

efciency and super bright 1W LED’s. There are three colour groups (red, green and blue) whose

intensity can be controlled individually allowing the creation of an unlimited range of colours.

This unit will operate in Stand-alone, Master/Slave, Sound activated and DMX-512 control modes.

Features

• 36 x 1W LEDs: - Red (12), Green (12), and Blue (12)

• Ultra bright 1W LEDs

• Sound control via internal microphone

• Colour change speed and strobe effect adjustable via control panel

• Multi-colour changes

• RGB Colour mixing

• Master/Slave functions

• Sound activated

• Rugged compact housing

• Consumption: 49W

• Beam angle: 40 degrees

• Lamp life: 100,000 hours

• Power supply: AC 110 - 240V, 50Hz/60Hz

• Dimensions: 300 x 255 x 125mm

• Weight: 3.7Kgs

LED Display

Down

Button

Operation:

There are 7 different operation modes to choose from:

1) Static colour mode 3) Colour fade mode 5) Sound Active mode 7) DMX modes

2) Colour change mode 4) Auto Run mode 6) Master/Slave mode

1, Static colour mode

Mode button - By pressing the “MODE” button under the LED display, the LED display will show

“CL2”, you can then select one of the 7 static colours using the “UP” and “DOWN” buttons.

The Colour options are:

1, RED, 2, Green, 3, Blue, 4, Yellow, 5, Cyan 6, Purple, 7, White

2, Colour change mode

Mode button - Press the MODE button until the LED display shows “J92”, then you can select

the colour change speed using the “UP” and “DOWN” buttons.

The speed settings are from 01-99 (01 = slow, 99 = fast)

3, Colour fade mode

Mode button - Press the MODE button until the LED display shows “F99”, then you can select

the fade speed using the “UP” and “DOWN” buttons.

The speed settings are from 01-99 (01 = slow, 99 = fast)

4). Auto run mode

Mode button - Press the MODE button until the LED display shows “A--”, now the unit will run in

the Auto Run mode. The run speed can be pre-set by selecting the individual speed in the Colour

fade and Colour change modes

5). Sound Active mode

Mode button - Press the MODE button until the LED display shows “S31”, then you can select

the Sound sensitivity levels using the “UP” and “DOWN” buttons.

The sensitivity settings are from 00-31 (00 =low, 31 = high)

6). Master/Slave mode

Link the units together using a 3-pin DMX cable, then press the MODE button to select one of the

above modes. On the Slave units press the mode button until the LED display shows “SLA”. The

Slave units will then follow in sequence with the Master unit.

7). DMX Addressing mode

This unit has two DMX operation modes. Please see the next page for the DMX chart.

To access the 3 channel DMX mode, press the MODE button until the LED display shows “001.”

To access the 6 channel DMX mode, press the MODE button until the LED display shows “001”

Stage Wash 36 Operation

DMX Value/Function

3 Channel DMX Chart

6 Channel DMX chart

Detailed instructions for 6 channel DMX mode.

1). When using channel 1, 2 and 3, for colour mixing you can use channel 5 for the strobe effect.

2). When channel 6 is set to 0-31 and channel 5 is set to 0, you can then use channel 4 to obtain

Colour mixing. ( in this mode channel 1, 2 and 3 have no function)

3). When the value of channel 6 is between 32-223, you can use channel 5 to adjust the speed for

Colour mixing or Colour changing.

4). When the value of channel 6 is between 224-255, you can use channel 5 to adjust the sound

sensitivity to the desired level.

Channel

Value

000-255

Function

RED (0 - 100%)

GREEN (0 - 100%)

BLUE (0 - 100%)

Channel

Value

000-255

0-7

8-255

0-16

17-255

0-31

32-95

96-159

160-223

224-255

Function

RED (0 - 100%)

GREEN (0 - 100%)

BLUE (0 - 100%)

No function

Colour macro mixing

No function

Strobe/Speed Adjustment/Sound Sensitivity Adjustment

No function

Colour mixing

RGB colour change

7 colour change

Sound activation

DMX-512:

• DMX (Digital Multiplex) is a universal protocol used as a form of communication between

intelligent xtures and controllers. A DMX controller sends DMX data instructions form the

controller to the xture. DMX data is sent as serial data that travels from xture to xture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have

a data “out” terminal).

DMX Linking:

• DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all xtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX xtures try to use the

shortest cable path possible. The order in which xtures are connected in a DMX line does not

inuence the DMX addressing. For example; a xture assigned to a DMX address of 1 may be

placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a

xture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to

address 1 to that unit, no matter where it is located in the DMX chain.

DATA Cable (DMX cable) requirements (for DMX operation):

• The Stage Wash 36 can be controlled via DMX-512 protocol. The DMX address is set on the

back of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for

data input/output (gure 1).

Figure 1

Also remember that DMX cable must be daisy chained and cannot be split.

Stage Wash 36 DMX Set up

Further DMX cables can be purchased

from all good sound and lighting suppliers

or Prolight dealers.

Please quote:

CABL10 – 2M

CABL11 – 5M

CABL12 – 10M

Notice:

• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield

conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer

casing. Grounding the shield could cause a short circuit and erratic behaviour.

Special Note: Line termination:

• When longer runs of cable are used, you may need to use a terminator on the last unit to

avoid erratic behaviour.

Using a cable terminator (part number CABL90) will decrease the possibilities of erratic

behaviour.

5-Pin XLR DMX Connectors:

• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin

XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin

XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the

correct cable conversion.

Termination reduces signal transmission problems

and interferance. it is always advisable to connect a

DMX terminal, (resistance 120 Ohm 1/4 W) between

pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.

Stage Wash 36 DMX Set up

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Ledj Projecteur

Ledj

Ledj Stage Par Quad MKII Manuel utilisateur

Ledj

Ledj Slimline 229 Manuel utilisateur

Ledj

Ledj Spectra Led Flood (Exterior) Manuel utilisateur

Ledj

Ledj Slimline 9Q8 Manuel utilisateur

Ledj

Ledj Slimline 7T3 Manuel utilisateur

Ledj

Ledj LEDJ01 Manuel utilisateur

Ledj

Ledj Q Batten LEDJ300 Manuel utilisateur

Ledj

Ledj 19T3 Manuel utilisateur

Ledj

Ledj HEX Par 7 Manuel utilisateur

Ledj

Ledj LEDJ280 Manuel utilisateur

Ledj

Ledj Spectra Led Flood (Exterior) Manuel utilisateur

Ledj

Ledj Slimline 5Q5 Manuel utilisateur

Ledj

Ledj Q Pix Batten LEDJ97 Manuel utilisateur

Ledj

Ledj Xterior Wash 131 Manuel utilisateur

Ledj

Ledj Performer 18 Quad Zoom Manuel utilisateur

Ledj

Ledj Slimline 36 RGBW Manuel utilisateur

Ledj

Ledj LEDJ01 Manuel utilisateur

Ledj

Ledj Eco LED 64 Manuel utilisateur

Ledj

Ledj LEDJ98 Manuel utilisateur

Ledj

Ledj Omni WA-36 Manuel utilisateur

Ledj

Ledj ALU ZOOM PAR 64 Manuel utilisateur

Ledj

Ledj ALU ZOOM PAR 64 Manuel utilisateur

Ledj

Ledj STAGE COLOUR 24 TRI Manuel utilisateur

Ledj

Ledj Stage Wash 18 Manuel utilisateur

Manuels Projecteur populaires d'autres marques

VIZULO

VIZULO Micro Martin Guide de l'utilisateur

EuroLite

EuroLite LED IP FL-100 SMD Manuel utilisateur

Cooper Wheelock

Cooper Wheelock XB12 Manuel utilisateur

Allen + Roth

Allen + Roth 17624-000 Manuel utilisateur

ADJ

ADJ 4 STAGE PAK Manuel utilisateur

Cooper Lighting

Cooper Lighting EGL91SW233 Manuel utilisateur

Max

Max 37496 Manuel utilisateur

BEGA

BEGA 85 143 Manuel utilisateur

Beamz

Beamz 151.226 Manuel utilisateur

EuroLite

EuroLite LED IP FL-8 Manuel utilisateur

Perel

Perel ELS3 Manuel utilisateur

Perel

Perel ELS3WD Manuel utilisateur

LumX

LumX LM 36130 Manuel utilisateur

Xtricity

Xtricity 4-80053 Manuel utilisateur

Stahl

Stahl 6521/4 Series Manuel utilisateur

Ecosense

Ecosense EcoSpec Manuel utilisateur

Ayrton

Ayrton minipanel FX Manuel utilisateur

Commercial Electric

Commercial Electric TPAR2-PC-4K-BZ Manuel utilisateur