Ledj ALU ZOOM PAR 64 Manuel utilisateur

www.prolight.co.uk

ALU QUAD PAR 64

Order code: LEDJ113

USER MANUAL

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modifications to this equipment are not

subject to warranty.

Alu Quad Par 64 Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modification to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Only use the equipment indoors.

• Do not expose to flammable sources, liquids or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualified engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature fluctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualified

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

You should find inside the LEDJ carton the following items:

1, Alu Quad Par 64 Unit 2, Instruction manual

Technical Specifications:

DMX channels: 3/5/7 or 8 selectable

Power supply: 240V

18 Ultra Bright 8W Quad colour LEDs (12 x RGBW, 6 x RGBA)

Power consumption: 163W

Beam angle: 25 degrees

Built-in microphone

3 push button LED display

Dimensions: 300 x 270 x 220mm

Weight: 4.3Kgs

Operating modes: 1, Static colour mode

2, Built-in programmes

3, Sound active

Overview:

Alu Quad Par 64 Technical specifications

4, DMX

5, Master/slave

Identification:

1, DMX input

2, DMX output

3, LED display

4, Power cable

5, Fuse (2A/240V)

6, Mode button

7, Down button

8, Up button

Setup

Operating Instructions

The Alu Quad Par 64 is a DMX-512 controllable, full RGBW/RGBA colour mixing Par Can made up

of high efficiency and super bright 8W LEDs. There are two four colour groups (RGBW and RGBA)

whose intensity can be controlled individually allowing the creation of an unlimited range of

colours.

The Alu Quad Par 64 will operate in Stand-alone, Master/Slave, Sound activated and

DMX-512 control modes.

Operations:

There are 5 different operation modes to choose from:

1) Static colour mode 2) Built-in programme mode 3) Sound active mode

4) DMX mode 5) Master/slave

1). Static colour mode

By pressing the “MODE” button under the LED display, the LED display will show “C01”, then you

can select one of the 30 static colours using the “UP” and “DOWN” buttons.

2). Built-in programme mode

Press the MODE button until the LED display shows “P01”, now use the “UP” and “Down”

buttons to select one of the 6 built-in programmes. For the built-in programme list, please see the

built-in programme chart over leaf.

3). Sound active

Press the MODE button until the LED display shows “S01”, the unit will then run in Sound Active

mode. Select the sensitivity level from 00 - 99 via the “UP” and “Down” buttons.

Please note: The higher the value the more sensitive it will be and is set to “S50” as default.

4). DMX mode

To access any of the 4 DMX channel modes, press the MODE button until the LED display

shows “3CH”, now use the “UP” and “Down” buttons to select either the 3, 5, 7 or 8 channel

DMX modes. The DMX values and functions are as follows over leaf.

To set the units address, press the MODE button to show “001” on the LED display. Now use the

“UP” and “Down” buttons to set the desired address from “001” to “512”.

5) Master/slave mode

To set the unit into slave mode, set the slave units address to “001”. The slave unit(s) will now

follow in sequence with the master unit.

To set the unit as a master simply use any of the above modes.

Alu Quad Par 64 Setup

Alu Quad Par 64 DMX Charts

DMX Charts

3 channel DMX chart

5 channel DMX chart

7 channel DMX chart

CHANNEL VALUE FUNCTION

0-7

8-255

Blackout

30 preset static colours

0-255 Master dimmer 0-100%

1-5

6-10

11-255

Sound mode

Strobe (slow to fast)

CHANNEL VALUE FUNCTION

0-255 Red 0-100%

Green 0-100%

Blue 0-100%

Amber 0-100%

White 0-100%

0-255

CHANNEL VALUE FUNCTION

0-255 Red 0-100%

Green 0-100%

Blue 0-100%

Amber 0-100%

White 0-100%

0-255

Master dimmer 0-100%

60-255

1-5

6-10

11-255

Sound mode (7 colours)

Strobe (slow to fast)

Alu Quad Par 64 DMX Charts

DMX Charts

8 channel DMX chart

Built-in programme chart

CHANNEL VALUE FUNCTION

0-255 Red 0-100%

Green 0-100%

Blue 0-100%

Amber 0-100%

Red 0-100%

0-255

Green 0-100%

60-255

70-255

0-255

Blue 0-100%

White 0-100%

MODE OPERATION

5 colour change, every 3 seconds

30 colour change, every 3 seconds

5 colour fade, in every 3 seconds

30 colour fade, every 3 seconds

five colour change via sound

30 colour change via sound

P01

P02

P03

P04

P05

P06

Alu Quad Par 64 DMX setup

DMX-512:

• DMX (Digital Multiplex) is a universal protocol used as a form of communication between

intelligent fixtures and controllers. A DMX controller sends DMX data instructions form the

controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have

a data “out” terminal).

DMX Linking:

• DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all fixtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX fixtures try to use the

shortest cable path possible. The order in which fixtures are connected in a DMX line does not

influence the DMX addressing. For example; a fixture assigned to a DMX address of 1 may be

placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a

fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to

address 1 to that unit, no matter where it is located in the DMX chain.

DATA Cable (DMX cable) requirements (for DMX operation):

• The Alu Quad Par 64 can be controlled via DMX-512 protocol. The DMX address is set on the

back of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for

data input/output (figure 1).

Figure 1

Also remember that DMX cable must be daisy chained and cannot be split.

Further DMX cables can be purchased

from all good sound and lighting suppliers

or Prolight dealers.

Please quote:

CABL10 – 2M

CABL11 – 5M

CABL12 – 10M

Alu Quad Par 64 DMX setup

Notice:

• Be sure to follow figures 2 & 3 when making your own cables. Do not connect the cable’s shield

conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer

casing. Grounding the shield could cause a short circuit and erratic behaviour.

Special Note: Line termination:

• When longer runs of cable are used, you may need to use a terminator on the last unit to

avoid erratic behaviour.

Using a cable terminator (part number CABL90) will decrease the possibilities of erratic

behaviour.

5-Pin XLR DMX Connectors:

• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin

XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin

XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the

correct cable conversion.

Termination reduces signal transmission problems

and interferance. it is always advisable to connect a

DMX terminal, (resistance 120 Ohm 1/4 W) between

pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.

Technical Specifications

Weight & Dimensions

• Length…..............................................................................................................................300mm

• Width....................................................................................................................................270mm

• Height………....................................................................………...…………………………..220mm

• Weight……………………………………….............................................................................4.3kgs

Power

• AC input……………………………………..................................................AC 120V/240V, 50/60Hz

Fuse

• Main……………………………………………….....................................20mm Glass 2A Fast Blow

Control & Programming

• Data input…………………………………...........................……...Locking 3-pin XLR male socket

• Data output…………………………………….......................….Locking 3-pin XLR female socket

• Protocols…………………………………………......................................................DMX-512 USITT

• DMX channels…………………………………..............................................3/5/7 and 8 selectable

Alu Quad Par 64 Specifications

Autres manuels pour ALU ZOOM PAR 64

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Ledj Projecteur

Ledj

Ledj Q Colour LEDJ210 Manuel utilisateur

Ledj

Ledj STAR18 Manuel utilisateur

Ledj

Ledj LEDJ01 Manuel utilisateur

Ledj

Ledj Slimline 7T3 Manuel utilisateur

Ledj

Ledj Slimline 5Q5 Manuel utilisateur

Ledj

Ledj Stage Wash 18 Manuel utilisateur

Ledj

Ledj Omni WA-36 Manuel utilisateur

Ledj

Ledj ALU ZOOM PAR 64 Manuel utilisateur

Ledj

Ledj Quad illuminator Manuel utilisateur

Ledj

Ledj Spectra Led Flood (Exterior) Manuel utilisateur

Ledj

Ledj LEDJ286 Manuel utilisateur

Ledj

Ledj STAGE COLOUR 24 TRI Manuel utilisateur

Ledj

Ledj Slimline 229 Manuel utilisateur

Ledj

Ledj LEDJ01 Manuel utilisateur

Ledj

Ledj LEDJ98 Manuel utilisateur

Ledj

Ledj Slimline 36 RGBW Manuel utilisateur

Ledj

Ledj PERFORMER 54 RGBW Manuel utilisateur

Ledj

Ledj Q Batten LEDJ300 Manuel utilisateur

Ledj

Ledj Xterior Wash 131 Manuel utilisateur

Ledj

Ledj INTENSE 12D4 CW Manuel utilisateur

Ledj

Ledj Stage Par Quad MKII Manuel utilisateur

Ledj

Ledj Spectra Par 6HEX10 Manuel utilisateur

Ledj

Ledj Performer 18 Quad Zoom Manuel utilisateur

Ledj

Ledj Eco LED 64 Manuel utilisateur

Manuels Projecteur populaires d'autres marques

VIZULO

VIZULO Micro Martin Guide de l'utilisateur

EuroLite

EuroLite LED IP FL-100 SMD Manuel utilisateur

Cooper Wheelock

Cooper Wheelock XB12 Manuel utilisateur

Allen + Roth

Allen + Roth 17624-000 Manuel utilisateur

ADJ

ADJ 4 STAGE PAK Manuel utilisateur

Cooper Lighting

Cooper Lighting EGL91SW233 Manuel utilisateur

Max

Max 37496 Manuel utilisateur

BEGA

BEGA 85 143 Manuel utilisateur

Beamz

Beamz 151.226 Manuel utilisateur

EuroLite

EuroLite LED IP FL-8 Manuel utilisateur

Perel

Perel ELS3 Manuel utilisateur

Perel

Perel ELS3WD Manuel utilisateur

LumX

LumX LM 36130 Manuel utilisateur

Xtricity

Xtricity 4-80053 Manuel utilisateur

Stahl

Stahl 6521/4 Series Manuel utilisateur

Ecosense

Ecosense EcoSpec Manuel utilisateur

Ayrton

Ayrton minipanel FX Manuel utilisateur

Commercial Electric

Commercial Electric TPAR2-PC-4K-BZ Manuel utilisateur