Commercial Electric TPAR2-PC-4K-BZ Manuel utilisateur

TPAR2 TWIN HEAD

FLOOD LIGHT

USE AND CARE GUIDE

THANK YOU

We appreciate the trust and conﬁdence you have placed in Commercial Electric through the purchase of this LED

ﬂood light. We strive to continually create quality products designed to enhance your home. Visit us online to see our

full line of products available for your home improvement needs. Thank you for choosing Commercial Electric!

Questions, problems, missing parts? Before returning to the store,

call Commercial Electric Customer Service

8 a.m. - 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday

1-844-584-3776

HOMEDEPOT.COM

Model No. TPAR2-PC-4K-BZ

TPAR2-PC-4K-WH

Table of Contents.......................... 2

Safety Information........................ 2

Pre-Installation.............................. 3

Planning Installation............................ 3

Speciﬁcations....................................... 3

Tools Required...................................... 3

Hardware Included..............................

Package Contents................................ 4

Installation..................................... 5

Care & Cleaning.............................

Troubleshooting............................

Operation...................................... 9

Warranty.......................................... 11

TABLE OF CONTENTS

SAFETY INFORMATION

IMPORTANT

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE NATIONAL

ELECTRICAL CODE AND LOCAL BUILDING CODES BY A PERSON FAMILIAR WITH THE

CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

PRECAUTIONS

☐Please read and understand this entire

manual before attempting to assemble,

install, or operate this light ﬁxture.

☐This light ﬁxture requires a 120 Volt AC

power source.

☐Some codes require installation by a

qualiﬁed electrician.

☐This light ﬁxture must be properly

grounded.

☐Make sure connections are secure using

wire nuts, crimp-on lugs or other

approved connecting devices

☐This light ﬁxture should be installed

outdoors to a wall or eave.

WARNING:

breaker or fuse. Place tape over the circuit

light ﬁxture.

WARNING: Risk of ﬁre. Keep the ﬁxture at

least 3 in. (76mm) from combustible materials.

CAUTION: Burn hazard. Allow the light ﬁxture

to cool before touching.

NOTICE: Do not connect this ﬁxture to a

dimmer switch.

INFORMATION: The device is tested and found to comply with Part 15 of the FCC Rules. Operation is subject

to two conditions: (1) This device may not cause harmful interference and, (2) this device must accept any

interference received, including any interference that may cause undesired operation.

These limits are designed to provide reasonable protections against harmful interference when the equip-

ment is operated in a commercial environment.

PREINSTALLATION

PLANNING INSTALLATION

Before installing the light ﬁxture, ensure that all parts are present. Compare parts with the

Hardware Included and Package Contents sections. If any part is missing or damaged, do

not attempt to assemble, install, or operate this light ﬁxture.

SPECIFICATIONS

TOOLS REQUIRED

Wire strippers/

cutters

Circuit tester

Safety

goggles

Work

gloves

Silicone

sealant

Ladder

Phillips

screwdriver

Lumens (Light Output) 1500 Lumens

Watts (Power Consumption) 20 Watts LED

Replaces 75W Incandescent

Lumens/Watts (Efficacy) 100 Lumens per watt

Power Requirements (Input Voltage) 120V

Light Color (CCT) 4000 Kelvin (Bright White)

Dimmable Non-Dimming (Do not wire to dimming switch)

Operating Modes Switch-Controlled:

Flip switch to turn light ﬁxture ON and OFF.

3HOMEDEPOT.com

Please contact 1-844-584-3776 for further assistance.

PREINSTALLATION CONTINUED

PACKAGE CONTENTS

Part Description Quantity

ALight fixture 1

Mounting plate tightening screw (pre-installed)

Mounting plate bracket (pre-installed)

Hanger wire for hands-free installation (pre-installed)

HARDWARE KIT

NOTE: Hardware not shown to actual size.

AA BB CC DD EE

Part Description Quantity

AA #8-32 x 3/4" Philips head screw 2

BB Wire nut 3

CC Mounting plate with ground wire 1

DD 10-24 x 5/4 Philips head screw 1

EE Mounting screw cover plug 1

INSTALLATION

1FOR BEST RESULTS

☐Install light 8-15 feet above the ground.

☐Do NOT wire to dimming switch.

☐When mounting to a wall, make sure

the ﬁxture is 7 in. away from eave and

13 inches away from inside corner of

the exterior wall (ﬁg 2).

Wall Mount Eave Mount

1-1/2" 1-1/2"

Round Octagonal

NOTE:

Mounting plate bracket (C) mounts to standard

recessed junction boxes. Junction box must

be at least 1-1/2 inch deep for proper

installation. (fig 3).

(ﬁg 3).

(ﬁg 1).

(ﬁg 2).

2SHUT OFF ELECTRIC POWER OFF

☐Verify wall switch is in OFF position (ﬁg 4).

☐

the circuit breaker that supplies power

At the main electrical panel, turn off

to the junction box you are working on

(ﬁg 5).

☐For screw-in type fuses, unscrew the

fuse that supplies power to the junction box

you are working on (ﬁg 6). (ﬁg 4). (ﬁg 5). (ﬁg 6).

13 in. 13 in

7 in

5HOMEDEPOT.com

Please contact 1-844-584-3776 for further assistance.

(ﬁg 7).

INSTALLATION CONTINUED

☐Align the slots on the mounting plate

bracket (C) with the holes of the junction

box. Use two (2) or four (4) philips head

screws (AA) to attach the mounting plate

bracket (C) to the junction box.

☐For wall mount, the "TOP" arrow must

point upward.

☐For eave mount, the "TOP" arrow must

point toward the building.

4HANG FIXTURE FROM

MOUNTING PLATE

BRACKET

☐For hands free mounting, place the hanger

wire hook into the slot of the mounting plate

bracket (C) to support the fixture while

connecting the wires.

TIP: Ensure the light ﬁxture (A) can safely

hang onto the mounting plate bracket (C) to allow

use of both hands to make the wiring connections

(fig 8).

(ﬁg 8).

INSTALL THE

MOUNTING

PLATE TO THE

JUNCTION BOX

INSTALLATION CONTINUED

5MAKE THE ELECTRICAL

CONNECTIONS

☐

If necessary, strip 3/8" of insulation

from junction box and lighting fixture

wires (fig 10). Connect wires by twisting

the exposed wires together and using

the wire nuts (BB). Ensure no loose

wires.

Connect lighting fixture black wire to

junction box black wire (line), lighting

fixture white wire to junction box white

wire (common), the junction box ground

wire to the green lighting fixture ground

wire, which is attached to the mounting

plate (C)

(ﬁg 9).

Black (Line)

White

(Common)

Green (Ground)

Junction Box

Non-Dimming Wiring Diagram

TIP:

Hold stripped ends near each other and

align any frayed strands (do not twist wires).

Push the wires into wire nut (BB) and use

your ﬁngers to twist the wire nut clockwise

until tight. Check for tightness by pulling

wires.

7HOMEDEPOT.com

Please contact 1-844-584-3776 for further assistance.

(ﬁg 10).

(ﬁg 11).

(ﬁg 12).

INSTALLATION CONTINUED

6MOUNT THE LIGHT

FIXTURE

☐Verify the ﬁxture is ﬂush with the wall.

☐Once wiring is complete, align the

mounting screw hole in the light

fixture with the mounting screw hole

in the mounting plate bracket (C).

☐Tighten the mounting plate screw (B)

until the fixture (A) is firmly secured

against the wall or eave.

7CAULK AROUND THE

LIGHT FIXTURE

8INSTALL BULBS AND

AIM THE LAMP HEADS

☐After ﬁxture is securely mounted, install

two PAR halogen or LED bulbs (sold

separately) into the lamp heads.

☐Loosen the thumb screw on each lamp

head to allow rotation for aiming each

lamp head. Once aimed, tighten the

screws on each lamp head to fix the

desired angle.

☐From the breaker and switch, turn

power back ON to the light fixture to

verify light fixture illuminates.

WARNING: Risk of ﬁre. Keep the lamp heads

at least 12 in. from combustible materials.

CAUTION: Keep lamp heads 30° below

horizontal to prevent water damage and

electrical shock.

IMPORTANT INFORMATION: PAR Halogen/LED

bulbs are sold separately. If you need to

purchase please contact your retail store.

BNOTICE: Failure to properly caulk around the

back face of the light fixture and mounting surface

could lead to water damage and is not covered under

warranty.

NOTE: When attaching the light fixture (A) to a

surface mount junction box, caulk between the

mounting plate and junction box.

☐Caulk around the back face of the light fixture

shown in (fig 12) with silicone sealant

(not included).

☐Ensure the switch powering the light

fixture is turned to the ON position and

leave it ON at all times to ensure

automatic dusk-to-dawn operation.

SWITCH

CONTROLLED

OPERATION

DUSKTODAWN MODE

DUSK-TO-DAWN OPERATION

AUTOMATIC

NIGHTTIME ON

DAYTIME OFF

Light ﬁxture (A) includes integral photocell for dusk-to-dawn operation which

enables the light ﬁxture to automatically turn ON when dark outside and turn

OFF when the sun rises, thus saving you energy.

NOTE: If photocell is located in an area

under heavy shade, the photocell may not

detect enough light and may turn the light

ﬁxture on.

TIP: To test if the light ﬁxture and photocell

work properly, run power to the ﬁxture and

cover the photocell to turn ﬁxture ON.

Shine a light into the photocell to see if

ﬁxture turns OFF.

SWITCH CONTROLLED

Switch controlled operation enables the light fixture to

turn ON and OFF by flipping a switch that controls the

electricity to the junction box powering the fixture. The

light fixture will not turn ON and OFF automatically, but is

manually controlled.

(ﬁg 13).

(ﬁg 14).

9HOMEDEPOT.com

Please contact 1-844-584-3776 for further assistance.

CARE AND CLEANING

☐

appearance, clean the light ﬁxture with clear water and a soft, damp cloth only.

☐Do not use abrasive cleaners or cleaners that contain alcohol. Do not apply paints,

solvents, or any other chemicals on this light ﬁxture. They could cause a premature

deterioration of the ﬁnish and may void the warranty.

☐Do not spray the light ﬁxture with a hose or power washer.

TROUBLESHOOTING

Problem Possible Cause Solution

Light does not

turn ON

No power to the ﬁxture

Check if circuit breaker is tripped

Conﬁrm wall switch is On Verify

wiring to ﬁxture is correct (turn

Fixture is sensing daylight Cover photocell. Wait several

seconds until ﬁxture turns ON.

Light cycles

ON and OFF

continuously

Photocell light sensor is

sensing reﬂected light

Relocate light ﬁxture to a location

where there is no reﬂected light.

OR Cover photocell light sensor and

use the wall switch to turn the light

fixture ON and OFF

OR Cover the photocell light sensor

and use the wall switch to turn the

light fixture ON and OFF

Light stays ON

Photocell light sensor is in

a shaded area

Shine a flashlight into the light sensor

and wait a couple minutes. If the light

turns OFF, the fixture should be

moved to a location with enough light

in the daylight hours for the light

sensor to work.

Photocell light sensor is faulty

a ﬂashlight is shined on the light

sensor for a few minutes, then

the sensor may be faulty. Please

contact customer service.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Commercial Electric Projecteur

Commercial Electric

Commercial Electric POWERFLOOD X PWRFX110-PC-4K-BZ Manuel utilisateur

Commercial Electric

Commercial Electric FSXD30-MS-4K-BZ Manuel utilisateur

Commercial Electric

Commercial Electric TPAR-PC-BZ Manuel utilisateur

Commercial Electric

Commercial Electric PWRF20-4K-BZ Manuel utilisateur

Commercial Electric

Commercial Electric FSNX28-5CCT-BZ Manuel utilisateur

Commercial Electric

Commercial Electric FSNX50-PC-4K-BZ Manuel utilisateur

Commercial Electric

Commercial Electric POWERFLOOD X PWRFX70-PC-4K-BZ Manuel utilisateur

Commercial Electric

Commercial Electric PWRF50-PC-4K-BZ Manuel utilisateur

Commercial Electric

Commercial Electric 60205161 Manuel utilisateur

Commercial Electric

Commercial Electric FUSION FSN 15-4K-BZ Manuel utilisateur

Manuels Projecteur populaires d'autres marques

VIZULO

VIZULO Micro Martin Guide de l'utilisateur

EuroLite

EuroLite LED IP FL-100 SMD Manuel utilisateur

Cooper Wheelock

Cooper Wheelock XB12 Manuel utilisateur

Allen + Roth

Allen + Roth 17624-000 Manuel utilisateur

ADJ

ADJ 4 STAGE PAK Manuel utilisateur

Cooper Lighting

Cooper Lighting EGL91SW233 Manuel utilisateur

Max

Max 37496 Manuel utilisateur

BEGA

BEGA 85 143 Manuel utilisateur

Beamz

Beamz 151.226 Manuel utilisateur

EuroLite

EuroLite LED IP FL-8 Manuel utilisateur

Ledj

Ledj PERFORMER 36 RGB Manuel utilisateur

Perel

Perel ELS3 Manuel utilisateur

Perel

Perel ELS3WD Manuel utilisateur

LumX

LumX LM 36130 Manuel utilisateur

Xtricity

Xtricity 4-80053 Manuel utilisateur

Stahl

Stahl 6521/4 Series Manuel utilisateur

Ecosense

Ecosense EcoSpec Manuel utilisateur

Ayrton

Ayrton minipanel FX Manuel utilisateur