LaserLiner EvolutionCross-Laser 8P PowerBright Manuel utilisateur

EvolutionCross-Laser 8P PowerBright

Bedienungsanleitung

Operating instructions

Gebruiksaanwijzing

Mode d´emploi

3-8

3-10

11-18

19-26

27-34

4H 4V 1D

EvolutionCross-Laser 8P PowerBright

Optional: max. 50 m range

EvolutionCross-Laser 8P PowerBright

Warranty: The warranty period is 2 years from the date of purchase.

The warranty covers all material or manufacturing defects occurring during

this time. The following are excluded from warranty: Damage due

to improper use (e.g. operation with wrong type of current/voltage,

connection to unsuitable power source, fall onto hard surface, etc.) or

improper storage, normal wear and tear, and defects which only insignifi-

cantly impair the value or suitability for use. Any tampering by unauthorised

persons will render this warranty void. In the event that you need to claim

warranty, please take the complete device together with all information and

the invoice to one of our dealers or send it in to Umarex-Laserliner.

Note: This is a precision instrument which must be handled with care.

Avoid impacts and jarring. Store and transport the instrument in its case!

Turn off the unit when it is not in use! Clean with a soft cloth and glass

cleaner.

High-precision cross-line laser with 8 super-bright laser lines,

plumb laser and additional slope function.

The 4 horizontal laser diodes project a homogeneous 360° laser line, the 4 verti-

cal laser lines are aligned at right angles to one another. Special high-performance

laser diodes project extremely visible laser lines. Manual mode can be used to set

slopes by means of a motor. The laser cross at the top and the plumb laser allow

a plumb line to be drawn from the ceiling to the floor. Electronic positioning

motors controlled by temperature-stable sensors for automatic alignment,

2.5° self-levelling range. The pivoted housing can be turned with a vernier

adjustment mechanism and horizontal circle to permit exact positioning of laser

lines. Precision 1 mm/10 m. RX-Ready: The laser receiver, which is available as

an optional extra, can detect laser lines in a range of up to 50 m.

General safety instructions

Caution: Do not look directly into the beam. Lasers must be kept out of

reach of children. Never intentionally aim the

device at people. This is a quality laser measu-

ring device and is 100% factory adjusted within

the stated tolerance. For reasons of product

liability, we must also draw your attention to

the following: Regularly check the calibration before use, after transport and

after extended periods of storage. We also wish to point out that absolute

calibration is only possible in a specialist workshop. Calibration by yourself is

only approximate and the accuracy of the calibration will depend on the care

with which you proceed.

ENGLISH

Laser radiation!

Do not stare into the

beam or observe it directly

with optical instruments.

Class 2M laser

< 5 mW · 635-650 nm

EN 60825-1:2007-10

EvolutionCross-Laser 8P PowerBright

91011

1516

Laser emitting window

Battery compartment

Continuous horizontal

360° laser line

Knob for precision adjustment

5/8” thread (underside)

Window for plumb laser

(underside)

Adjustable feet with removable

rubber caps

Tripod adapter

Vertical laser line/

slope function: set the slope

LED Hand receiver mode

Hand receiver mode

Vertical laser line/

slope function: set the slope

Status indicator/

low battery charge LED

ON/OFF button

Automatic mode (auto)/slope

function (slope) LED indicator

Horizontal laser lines/ slope

function: activate/deactivate

(press and hold for 3 seconds);

axis switch-over

ENGLISH

EvolutionCross-Laser 8P PowerBright

Anti-shake function

The automatic sensor continuously levels the devices, even if they are in motion.

This makes device alignment easier, as it enables the laser to be set to a

required height by means of a crank tripod or a wall bracket, for example.

It also means that the laser can be used on vibrating surfaces and in windy

conditions. IMPORTANT: Precision is adversely affected during the set-up phase.

Note: If the unit is placed at an excessive angle (out of its 2,5° range),

the lasers will blink. If this should be the case, align the unit roughly with

the levelling feet (7) or place it on a more level surface.

Setting up

• Press the „ON/OFF“ switch (14).

• The automatic sensor aligns the device without any need for

operator intervention. To accomplish this, two electronic sensors

are used to detect the X and Y axes. The working angle ist ±

2,5°. During the set-up phase, the auto LED (15) flashes rapidly.

When levelling is complete, the auto LED lights up continuously.

• Switch the lasers on using the H slope, V1 or V2 buttons (press

briefly). Maximum visibility of the laser line is obtained when

hand receiver mode is switched off (button 11, indicator

light 10 off).

Attention: Only insert rechargeable batteries into the charger – risk of

explosion! Used batteries must not be disposed of with regular domestic

waste; instead, they can be deposited at a collection point for batteries or

hazardous waste.

Battery (NiMH) charging

• Charge the batteries (NiMH) fully before using the laser unit. Insert only

rechargeable (i.e. secondary) batteries into the charging unit. Be sure that the

batteries are marked with the label „RECHARGEABLE“.

• Insert the rechargeable batteries into the charger and connect the charger to the

mains power supply. Observe the charger operating instructions. As soon as the

rechargeable batteries are charged up, disconnect the charger from the mains

power supply.

• Insert the rechargeable batteries (NiMH) into the laser unit. Do this by opening the

battery compartment (2) and inserting the batteries according to the symbols. If

the status indicator (13) flashes, the rechargeable batteries need to be replaced.

ENGLISH

EvolutionCross-Laser 8P PowerBright

(16)

(9,12)

± 2,5°

auto

slope

3 sec

(16)

(9,12)

± 2,5°

autoslope

3 sec

Manual Slope function

This function deactivates the automatic sensor, which enables slopes to be

set. Press the H slope button and hold it down for 3 seconds until the auto

LED starts to flash very rapidly. The V1, V2 buttons are used to re-adjust the

slope by means of a motor. The H slope button (pressed briefly) is used to

switch over between axes. IMPORTANT: Since the automatic sensor is not

active, horizontal and/or

ENGLISH

EvolutionCross-Laser 8P PowerBright

(16)

slope

3 sec

auto LED status indicator

Automatic mode (auto) Slope function (slope)

auto auto auto auto

Continuous Rapid Every second Very rapid

OK Set-up phase X axis Y axis

TIP: Switch the required laser lines on before you activate the slope function.

Positioning laser lines

The top section of the laser unit can be turned on the plinth to align the

lasers approximately. The vernier adjustment mechanism (4) can be used to

position the lasers precisely. The freely rotatable horizontal circle (3) makes

it easy to turn the device to the required angle. Simply set the scale to zero,

then rotate the device to the angle you want.

Manual re-adjustment:

Steeper slopes can be set using the angle plate, which is available as an

optional extra (product ref. 080.75). To this end you need to use a crank

tripod, such as the 300 cm professional crank tripod, product ref. 080.34.

TIP: Allow the device to align itself automatically and set the angle plate to

the zero position. Next, deactivate the automatic sensor by pressing the H

slope button (and holding for 3 seconds). Finally, incline the device to the

angle you require.

ENGLISH

EvolutionCross-Laser 8P PowerBright

16 ENGLISH

Preparing the calibration check:

It is possible for you to check the calibration of the laser. To do this, position

the device midway between 2 walls, which must be at least 5 metres apart.

Switch the device on (Laser cross ON). The best calibration results are achie-

ved if the device is mounted on a tripod. 1. Mark point A1 on the wall.

2. Turn the device

through 180° and

mark point A2.

You now have a

horizontal reference

between points A1

and A2.

Checking the vertical line: Position the device about 5 m from a wall. Fix a

plumb bob with a line of 2.5 m length on the wall, making sure that the bob

can swing freely. Switch on the device and align the vertical laser to the plumb

line. The precision is within the specified tolerance if the deviation between the

laser line and the plumb line is not greater than ± 1.5 mm.

Checking the horizontal line:

Position the device about 5 m from a wall and

switch on the cross laser. Mark point B on the wall.

Turn the laser cross approx. 2.5 m to the right and

mark point C. Check whether the horizontal line

from point C is level with point B to within ± 2 mm. Repeat the process by

turning the laser to the left.

Performing the calibration check:

3. Position the device as near as possible to the wall at the height of

point A1.

4. Turn the device

through 180° and

mark point A3. The

difference between

points A2 and A3 is

the tolerance.

Note: If points A2 and A3 are more than 2 mm / 10 m, the device is in

need of calibration. Contact your authorised dealer or else the UMAREX-

LASERLINER Service Department.

2,5 m

< 2 mm = OK

A2 A2

< 2 mm / 10 m = OK

EvolutionCross-Laser 8P PowerBright

17ENGLISH

Working with the laser receiver RX (optional):

For levelling over longer distances or in conditions of bright light, use the

laser receiver RX. Switch on with button D; control lamp A will light up.

IMPORTANT: Set the laser unit to hand receiver mode (button 11).

The laser lines now pulsate at a high frequency (5 kHz) and become darker.

The pulsation allows the laser receiver to detect the laser lines.

Now move the receiver field (F) of the laser receiver through the laser lines

upwards and downwards (horizontal laser line) and/or sideways (vertical laser

line) until the centre LED (G) lights up. Now mark the horizontal and/or

vertical reference dimension.

Adjust the sensitivity of the laser receiver with button B.

The sound can be switched on or off with button E.

Power indicator

Switch accuracy

short range / long range

Sensitivity indicator light

RX 51:

Close range max. 15 m green –

Long range max. 50 m red

ON / OFF switch

Sound ON / OFF

Receiver field for laser beam

LED’s for Laserindication

(front, side, backside)

Universal mount

Battery compartment (backside)

RX 51

Note: The light intensity of the laser lines is greatest at their midpoints and

less toward their ends. Therefore at line ends the distance range for the

laser receiver is reduced somewhat. An even distribution of brightness can

be achieved by switching on all 4 horizontal laser lines. When this is done

the maximum range for laser reception is remains constant.

EvolutionCross-Laser 8P PowerBright

18 ENGLISH

Note: Regularly check the calibration before use, after transport and after

extended periods of storage

Technical data

Self-levelling range ± 2,5°

Precision + 1 mm / 10 m

Working range with laser receiver RX 51 max. 50 m

Laser wavelengths, line lasers / plumb laser 635 nm / 650 nm

Laser class/line laser output power 2M / < 5 mW

Laser class/plumb laser output power 2 / ÷1 mW

Power supply ECL 8P 3 x type AA

Battery/rechargeable battery life ca 5 Std. / ca. 8 h

Power supply laser receiver RX 51 1 x 9V Block

Weight ECL 8P (incl. battery) 1,3 kg

Dimensions (W x H x D) 195 x 130 x 130 mm

Operating temperature 0°C ... + 50°C

Storage temperature -10°C ... + 70°C

Article-No. (ECL)

EvolutionCross-Laser 8P PowerBright RX 048.200A

Subject to technical alterations 06/2009

Universal mount (optional):

The laser receiver RX can be fitted on measuring

staffs with the universal mount. The Flexi measuring

staff (Art. No. 080.50) is always recommended when

measuring from floor heights. It also allows you

to determine heights directly without any need for

calculation.

Autres manuels pour EvolutionCross-Laser 8P PowerBright

Table des matières

Autres manuels LaserLiner Instrument de mesure

LaserLiner

LaserLiner GreenLine-Laser 2 P Manuel utilisateur

LaserLiner

LaserLiner DistanceMaster 100 Manuel utilisateur

LaserLiner

LaserLiner RangeXtender G 30 Manuel utilisateur

LaserLiner

LaserLiner SmartVision-Laser Manuel utilisateur

LaserLiner

LaserLiner AutoControl-Master ACM Manuel utilisateur

LaserLiner

LaserLiner ThermoMaitre Manuel utilisateur

LaserLiner

LaserLiner ClimaCheck Manuel utilisateur

LaserLiner

LaserLiner MultiMeter-Pocket Manuel utilisateur

LaserLiner

LaserLiner AirMonitor PURE Manuel utilisateur

LaserLiner

LaserLiner RangeXtender RX 30 Manuel utilisateur

LaserLiner

LaserLiner ThermoInspector Manuel utilisateur

LaserLiner

LaserLiner DistanceMaster Vision Manuel utilisateur

LaserLiner

LaserLiner LaserMeter X20 Manuel utilisateur

LaserLiner

LaserLiner CenterScanner Plus TX Manuel utilisateur

LaserLiner

LaserLiner DistanceMaster Compact Manuel utilisateur

LaserLiner

LaserLiner SensoLite 110 Manuel utilisateur

LaserLiner

LaserLiner CompactPlane-Laser 3D Manuel utilisateur

LaserLiner

LaserLiner WoodTester Manuel utilisateur

LaserLiner

LaserLiner VideoFlex HD Manuel utilisateur

LaserLiner

LaserLiner Quadrum Manuel utilisateur

LaserLiner

LaserLiner CondenseSpot Manuel utilisateur

LaserLiner

LaserLiner LaserRange-Master T4 Pro Manuel utilisateur

LaserLiner

LaserLiner SuperSquare Manuel utilisateur

LaserLiner

LaserLiner CoatingTest-Master Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur