Lantech IPGS-0204DSFP Manuel utilisateur

IPGS-0204DSFP

4 10/100/1000T + 2 Dual Speed SFP Industrial Switch w/4 PoE 802.3 at/af Injectors

Quick Installation Guide

Introduction

The Lantech IPGS-0204DSFPis a cost-effective solution, which meets the high reliability requirements demanded by

industrial applications. Besides, the equipment meets IEEE 802.3at standard, the switch can provides 30 Watts output per

PoE port for Powered Devices. The switch supports wide operating temperature, range from -40°C to 75°C.

The IPGS-0204DSFP is designed to meet the demands of Industrial environments, comes packaged in a robust IP30

housing and has been tested extensively to meet Industrial EMI and EMC standards. Rigorous mechanical testing has

also been undertaken to comply with free fall, shock and vibration stability test requirements.

With voltage boost design, the IPGS-0204DSFP can work from 24V input power source and boost the voltage to 48VDC

to feed the PoE power over Ethernet cable for any vehicles that usually has 24V power source. The slim compact design

is able to fit in variety of cabinets and space.

Housing Dimension

Installation package

This unit can be installed by din-rail mounted or wall-mounted. Din-rail brackets and wall-mounted bracket are included.

Power and alarm relay connection

The PWR1 and PWR2 can be redundant with each other or you can use one of them to supply the switch.

The middle contact was designed for alarm relay connection.

Dip switch function

The SFP speed can be selected by switching the DIP switch.

LED indicator

Speed

ON –1000M speed is detected.

OFF –10M or 100M speed is detected

PWR1

ON -- when V1+, V1- is connected

ON –port 6 SFP fiber is detected

OFF –port 6 SFP fiber is not

detected.

Flashing –port 6 SFP fiber is active

LNK /ACT

ON—TX link is detected

OFF –TX port is not detected

Flashing –TX port is active

Din Rail Bracket x 1

6 pin Terminal Block x1

PWR2

ON -- when V2+, V2- is connected

FAULT

ON –

connect only PW1 or PW2.

OFF-

both PW1 and PW2 are connected

ON –port 5 SFP fiber is detected

OFF –port 5 SFP fiber is not detected.

Flashing –port 5 SFP fiber is active

1,2,3,4

ON—PD is detected on designated

port.

OFF –no PD is detected

Recommendation for Shielded network cables

STP cables have additional shielding material that is used to reduce external interference. The

shield also reduces the emission at any point in the path of the cable. Our recommendation is

to deploy an STP network cable in demanding electrical environments. Examples of

demanding indoor environments are where the network cable is located in parallel with

electrical mains supply cables or where large inductive loads such as motors or contactors are

in close vicinity to the camera or its cable. It is also mandatory to use an STP cable where the

power device (like IP camera) is used outdoors or where the network cable is routed outdoors.

Table des matières

Autres manuels Lantech Changer

Lantech

Lantech LES-2400-RPS Manuel utilisateur

Lantech

Lantech LGS-1104 Manuel utilisateur

Lantech

Lantech IPGS-5 Series Manuel utilisateur

Lantech

Lantech IPGS-5008T Series Manuel utilisateur

Lantech

Lantech TES-R6616XFT Manuel utilisateur

Lantech

Lantech IPGS-0016 Manuel utilisateur

Lantech

Lantech IPES-0208CA-12V Manuel utilisateur

Lantech

Lantech IPES-0008A Series Manuel utilisateur

Lantech

Lantech IPES-5408T-43 Manuel utilisateur

Lantech

Lantech IPES/IES-5416DFT Series Manuel utilisateur

Lantech

Lantech LGS-2424C Manuel utilisateur

Lantech

Lantech IES-2208CA Manuel utilisateur

Lantech

Lantech IES-5416DF Series Manuel utilisateur

Lantech

Lantech IGC-0101DSFP Manuel utilisateur

Lantech

Lantech LPGS-2424C Series Manuel utilisateur

Lantech

Lantech IPES-0005B Series Manuel utilisateur

Lantech

Lantech IPWMR-3006 Manuel utilisateur

Lantech

Lantech IGS-2206C Manuel utilisateur

Lantech

Lantech IPES-3424DSFP-2P-PT Manuel utilisateur

Lantech

Lantech IPES-3408GSFP Manuel utilisateur

Lantech

Lantech IPES-5408T Manuel utilisateur

Lantech

Lantech 5 10/100TX w/ 4 PoE Injector Industrial... Manuel utilisateur

Lantech

Lantech IGS-2404 Manuel utilisateur

Lantech

Lantech IES-22812F-2P Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur