KROHNE OPTISOUND 3020 Manuel utilisateur

OPTISOUND 3020 Quick setup guide

Ultrasonic Level Transmitter

Foundation Fieldbus

Contents

OPTISOUND 3020 • Foundation Fieldbus

62690-EN-220310

Contents

1 For your safety ......................................................................................................................... 3

1.1 Authorised personnel ....................................................................................................... 3

1.2 Appropriate use................................................................................................................ 3

1.3 Warning about incorrect use............................................................................................. 3

1.4 General safety instructions............................................................................................... 3

1.5 EU conformity................................................................................................................... 3

1.6 NAMUR recommendations .............................................................................................. 4

2 Product description ................................................................................................................. 5

2.1 Conguration.................................................................................................................... 5

3 Mounting................................................................................................................................... 6

3.1 Mounting instructions ....................................................................................................... 6

4 Connecting to power supply................................................................................................... 7

4.1 Connection procedure...................................................................................................... 7

4.2 Wiring plan, single chamber housing................................................................................ 8

4.3 Wiring plan, double chamber housing .............................................................................. 8

5 Set up with the display and adjustment module PLICSCOM .............................................. 9

5.1 Insert display and adjustment module.............................................................................. 9

5.2 Setup steps ...................................................................................................................... 9

5.3 Menu schematic............................................................................................................. 12

6 Supplement ............................................................................................................................ 14

6.1 Technical data ................................................................................................................ 14

Information:

This quick setup guide enables quick setup and commissioning of

your instrument.

Youcanndfurtherinformationinthecorresponding,comprehensive

operating instructions as well as in the Safety Manual for instruments

withSILqualication.

Operating instructions OPTISOUND 3020 C - Foundation Field-

bus: Document-ID 51116

Editing status of the quick setup guide: 2022-03-07

1 For your safety

OPTISOUND 3020 • Foundation Fieldbus

62690-EN-220310

1 For your safety

1.1 Authorised personnel

All operations described in this documentation must be carried out

onlybytrained,qualiedpersonnelauthorisedbytheplantoperator.

Duringworkonandwiththedevice,therequiredpersonalprotective

equipment must always be worn.

1.2 Appropriate use

OPTISOUND3020Cisasensorforcontinuouslevelmeasurement.

Youcannddetailedinformationabouttheareaofapplicationin

chapter " Product description".

Operational reliability is ensured only if the instrument is properly

usedaccordingtothespecicationsintheoperatinginstructions

manual as well as possible supplementary instructions.

1.3 Warning about incorrect use

Inappropriateorincorrectuseofthisproductcangiverisetoapplica-

tion-specichazards,e.g.vesseloverllthroughincorrectmounting

oradjustment.Damagetopropertyandpersonsorenvironmental

contaminationcanresult.Also,theprotectivecharacteristicsofthe

instrument can be impaired.

1.4 General safety instructions

Thisisastate-of-the-artinstrumentcomplyingwithallprevailing

regulationsanddirectives.Theinstrumentmustonlybeoperatedina

technicallyawlessandreliablecondition.Theoperatorisresponsi-

ble for the trouble-free operation of the instrument. When measuring

aggressiveorcorrosivemediathatcancauseadangeroussituation

if the instrument malfunctions, the operator has to implement suitable

measures to make sure the instrument is functioning properly.

The safety instructions in this operating instructions manual, the na-

tionalinstallationstandardsaswellasthevalidsafetyregulationsand

accidentpreventionrulesmustbeobservedbytheuser.

Forsafetyandwarrantyreasons,anyinvasiveworkonthedevice

beyond that described in the operating instructions manual may be

carried out only by personnel authorised by the manufacturer. Arbi-

traryconversionsormodicationsareexplicitlyforbidden.Forsafety

reasons,onlytheaccessoryspeciedbythemanufacturermustbe

used.

Toavoidanydanger,thesafetyapprovalmarkingsandsafetytipson

thedevicemustalsobeobserved.

1.5 EU conformity

ThedevicefullsthelegalrequirementsoftheapplicableEUdirec-

tives.ByaxingtheCEmarking,weconrmtheconformityofthe

instrumentwiththesedirectives.

The EU conformity declaration can be found on our homepage.

1 For your safety

OPTISOUND 3020 • Foundation Fieldbus

62690-EN-220310

1.6 NAMUR recommendations

NAMUR is the automation technology user association in the process

industry in Germany. The published NAMUR recommendations are

acceptedasthestandardineldinstrumentation.

ThedevicefullstherequirementsofthefollowingNAMURrecom-

mendations:

• NE 21 – Electromagnetic compatibility of equipment

• NE43–Signallevelforfaultinformationfrommeasuringtransduc-

ers

• NE53–Compatibilityofelddevicesanddisplay/adjustment

components

For further information see www.namur.de.

2 Product description

OPTISOUND 3020 • Foundation Fieldbus

62690-EN-220310

2 Product description

2.1 Conguration

Thetypelabelcontainsthemostimportantdataforidenticationand

use of the instrument:

• Instrument type

• Articleandserialnumberdevice

• Article number documentation

• Technicaldata:Approvals,processtemperature,processtting/

material,signaloutput,voltagesupply,protection

Type label

3 Mounting

OPTISOUND 3020 • Foundation Fieldbus

62690-EN-220310

3 Mounting

3.1 Mounting instructions

The reference plane for the measuring range is the lower edge of the

transducer.

Make sure that a minimum distance from the reference plane - the

so-calleddeadzone,inwhichmeasurementisnotpossible-is

maintained.Theexactvalueofthedeadzoneisstatedinchapter"

Technical data".

Fig. 1: Minimum distance to the max. level

1 blocking distance

2 Reference plane

Mountthesensoratleast200mm(7.874in)awayfromthevessel

wall.

> 200 mm

Fig. 2: Mounting on round vessel tops

1 Reference plane

2 Vessel center or symmetry axis

Reference plane for

measuring range

Mounting

4 Connecting to power supply

OPTISOUND 3020 • Foundation Fieldbus

62690-EN-220310

4 Connecting to power supply

4.1 Connection procedure

Proceed as follows:

1. Unscrew the housing lid

2. Ifadisplayandadjustmentmoduleisinstalled,removeitbyturn-

ing it to the left

3. Loosencompressionnutofthecableglandandremoveblind

plug

4. Removeapprox.10cm(4in)ofthecablemantle,stripapprox.

1cm(0.4in)ofinsulationfromtheendsoftheindividualwires

5. Insert the cable into the sensor through the cable entry

6. Lifttheopeningleversoftheterminalswithascrewdriver(see

following illustration)

7. Insert the wire ends into the open terminals according to the wir-

ing plan

Fig. 3: Connection steps 6 and 7

8. Pressdowntheopeningleversoftheterminals,youwillhearthe

terminal spring closing

9. Check the hold of the wires in the terminals by lightly pulling on

them

10. Connect the shielding to the internal ground terminal, connect the

externalgroundterminaltopotentialequalisation

11. Tighten the compression nut of the cable entry gland. The seal

ring must completely encircle the cable

12. Screw the housing lid back on

Theelectricalconnectionisnished.

4 Connecting to power supply

OPTISOUND 3020 • Foundation Fieldbus

62690-EN-220310

4.2 Wiring plan, single chamber housing

I2C

Display

12 5678

Fig. 4: Wiring plan - single chamber housing

1 Voltage supply, signal output

4.3 Wiring plan, double chamber housing

I2C

Fig. 5: Wiring plan - double chamber housing

1 Voltage supply, signal output

Wiring plan

5 Set up with the display and adjustment module PLICSCOM

OPTISOUND 3020 • Foundation Fieldbus

62690-EN-220310

5 Set up with the display and adjustment

module PLICSCOM

5.1 Insert display and adjustment module

The display and adjustment module can be inserted into the sensor

andremovedagainatanytime.Itisnotnecessarytointerruptthe

voltagesupply.

Proceed as follows:

1. Unscrew the housing lid

2. Place the display and adjustment module in the desired position

ontheelectronics(fourpositionsin90°osetcanbeselected)

and turn to the right until it clicks into place.

3. Screw housing lid with inspection window tightly back on

Disassemblyiscarriedoutinreverseorder.

The display and adjustment module is powered by the sensor, an ad-

ditional connection is not necessary.

Fig. 6: Insert display and adjustment module in the single chamber housing

Note:

Ifyouintendtoretrottheinstrumentwithadisplayandadjustment

moduleforcontinuousmeasuredvalueindication,ahigherlidwithan

inspection glass is required.

5.2 Setup steps

1. Go to the menu " Basic adjustment"viathedisplayandadjust-

ment module.

Mount/dismount display

and adjustment module

Set parameters

5 Set up with the display and adjustment module PLICSCOM

OPTISOUND 3020 • Foundation Fieldbus

62690-EN-220310

▶Basicadjustment

Display

Diagnostics

Service

Info

2. Carry out the adjustment in the menu items " Min. adjustment"

and " Max. adjustment".

Max.adjustment

100.00 %

1.000 m(d)

2.000 m(d)

Min. adjustment

0.00 %

5.000 m(d)

4.000 m(d)

3. Select in the menu item " Medium" the medium of your applica-

tion,forexample"Aqueous solution".

Medium

Liquid

4. Select in the menu item " Application"thevessel,theapplication

andthevesselform,forexample,"Storage tank".

Vessel shape

Storage tank

The sensor measures the distance from the sensor to the medium

surface.Forindicationofthereallevel,anallocationofthemeasured

distance to the percentage height must be carried out.

Theactuallevelisthencalculatedonthebasisoftheseentered

values.Atthesametime,theoperatingrangeofthesensorislimited

frommaximumrangetotherequestedrange.

Parameter adjustment

Table des matières

Autres manuels KROHNE Émetteur

KROHNE

KROHNE OPTIBAR 5060 Schéma de câblage

KROHNE

KROHNE OPTIFLEX 2200 C Schéma de câblage

KROHNE

KROHNE PM 3050 Manuel utilisateur

KROHNE

KROHNE OPTISOUND 3010 C Manuel utilisateur

KROHNE

KROHNE OPTISOUND 3020 Quick Manuel utilisateur

KROHNE

KROHNE OPTISOUND 3010 C Manuel utilisateur

KROHNE

KROHNE OPTIBAR 5060 eDP Schéma de câblage

KROHNE

KROHNE OPTISOUND 3020 C Manuel utilisateur

KROHNE

KROHNE OPTIWAVE 400 Series Schéma de câblage

KROHNE

KROHNE DR 400 Series Schéma de câblage

KROHNE

KROHNE OPTISOUND 3030 C Manuel utilisateur

KROHNE

KROHNE OPTISOUND 3020 C Manuel utilisateur

KROHNE

KROHNE OPTISOUND 3010 C Manuel utilisateur

KROHNE

KROHNE OPTISOUND 3010 C Manuel utilisateur

KROHNE

KROHNE OPTIBAR DP 3050 Manuel utilisateur

KROHNE

KROHNE OPTIWAVE 6300 C Schéma de câblage

KROHNE

KROHNE OPTIWAVE 1010 Schéma de câblage

KROHNE

KROHNE OPTISOUND 3020 C Manuel utilisateur

KROHNE

KROHNE OPTITEMP TT 12 R Manuel utilisateur

KROHNE

KROHNE OPTIBAR P 1010 Schéma de câblage

KROHNE

KROHNE OPTIWAVE X400 Schéma de câblage

KROHNE

KROHNE OPTIWAVE X500 Schéma de câblage

KROHNE

KROHNE OPTIBAR DP 7060 Schéma de câblage

KROHNE

KROHNE OPTIWAVE 1010 Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur